Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
Page 5
INPUT SELECT ① ② EXIT : END AUTO TUNING MANUAL TUNING CH ALLOCATION LANGUAGE ENGLISH AV1 OUTPUT AV COLOUR AUTO EXIT : END MENU: RETURN...
Page 6
AUTO INSTALLATION LANGUAGE ENGLISH COUNTRY AUTO TUNING ENGLISH EXIT : END MENU: RETURN AUTO INSTALLATION LANGUAGE ENGLISH COUNTRY AUTO TUNING EXIT : END MENU: RETURN AUTO INSTALLATION LANGUAGE ENGLISH COUNTRY AUTO TUNING EXIT : END AUTO INSTALLATION LANGUAGE ENGLISH COUNTRY AUTO TUNING AUTO TUNING EXIT : END...
Page 7
AUTO TUNING MANUAL TUNING CH ALLOCATION LANGUAGE AUTO TUNING ENGLISH AV1 OUTPUT MANUAL TUNING AV COLOUR CH ALLOCATION AUTO LANGUAGE ENGLISH AV1 OUTPUT AV COLOUR EXIT : END MENU: RETURN AUTO EXIT : END MENU: RETURN AUTO TUNING MANUAL TUNING AUTO TUNING CH ALLOCATION LANGUAGE...
Page 8
NICAM AUTO BASS TREBLE BALANCE RESET AUTO EXIT : END MENU: RETURN N I C A M S T N I C A M M 1 N I C A M / M 2 N I C A M O F F AUTO TUNING MANUAL TUNING S T E R E O...
Page 9
Reading Marker 1 Marker 1 Marker 2 Marker 2 Marker 3 Marker 3 Jump Title Chapter Time Marker 1 Marker 2 Marker 3 Jump C D B A Title Marker 1 Chapter Marker 2 Time Marker 3 Jump Title Chapter Time...
Page 10
Play Mode Mode : Off – – – Repeat : Off – – – – – – Play Mode Program Playback Repeat : Off Play Mode Play Mode Mode : Program Mode : Program Repeat : Off – – – Repeat : Off –...
Page 11
Play Mode Mode : Off – – – Repeat : Off – – – – – – Program Playback 00:15:25 01:41:39 Title 1/3 Chapter 2/24 1/1 Eng Dolby Digital 1/2 Eng 00:08:32 00:51:03 Track 3/15 ® ® ® 3, 4, 5, and 6 ( ally 3.1.1, 4.1.2, 5.0.2, 5.0.5, 5.1.1, 5.2.1, 6.0 at Home Theater 3/15 00:00:00...
Page 12
B A C D B A C D / ovie-01.DIVX ovie-01 Select Files ovie-02 Repeat :Off View DivX(R) VOD Rental Folder-1 Select Files older-1 Select iles ovie-03 :Off This rental has 5 views left. Folder-2 older-2 Repeat :Off Repeat :Off ovie-04 Do you want to use one ovie-05...
Page 13
Parental E.B.L. Menu : Off : Off : Off : êìëëäàâ Parental Menu E.B.L. Night Mode : Off : English : Off : Off QSound TV Screen Subtitle Set Password : On : 4:3 : êìëëäàâ Digital Out : Bitstream Subtitle Set Password : English...
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES PERFORM A SAFETY CHECK AFTER SERVICING As for the places which need special attentions, they are indicated with the labels or seals on the Confirm that the screws, parts and wiring which cabinet, chassis and parts.
WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD MT PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector.
DISC REMOVAL METHOD AT NO POWER SUPPLY Remove the Back Cabinet and Angle Deck. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) Slide the Belt Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1) Take out the Disc from the DVD Deck.
TABLE OF CONTENTS • GREEN PRODUCT PROCUREMENT • LEAD-FREE SOLDER • OWNER'S MANUAL SERVICING NOTICES ON CHECKING ..............A1-1 HOW TO ORDER PARTS ................... A1-1 IMPORTANT ......................... A1-1 WHEN REPLACING DVD DECK ................A1-2 DISC REMOVAL METHOD AT NO POWER SUPPLY ..........A1-3 PARENTAL CONTROL - RATING LEVEL ..............
GENERAL SPECIFICATIONS LCD Size / Visual Size 15.0 inch / 380.1 mmV System LCD Type Color TFT LCD Number of Pixels 1024(H) x 768(V) View Range Left/Right 70/70 degree Up/Down 65/60 degree < Bright Dot 0 (Sorted Products) Zero Bright Dot Ratio Color System PAL / SECAM Speaker...
Page 21
Timer Back-up (at Power Off Mode) more than G-11 Remote Unit RC-PT Control Glow in Dark Remocon Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BF h ,44-BB h ,45-BA h ,45-BC h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs...
GENERAL SPECIFICATIONS T'TEXT Keys TEXT / TV Reveal / Skip Sub Page / Search+ Reveal / Search- Reveal Display Cancel HOLD Angle Marker F.T.B / Skip+ Skip- Slow+ / Blue Slow- / Red Play Mode/Yellow Green/Pause Normal F/T/B(Expand) F/T/B(Expand) / Normal Quick View Sub Page / Quick View Up/CH Up...
Page 23
GENERAL SPECIFICATIONS Wide Mode (AUTO/4:3/16:9) Reset TV Setting HD Zoom Picture Scroll (Vertical Position) PFC(Power Factor circuit) Freeze frame HD-Ready Plug and Play Scart Spec Scart1 AV in AV out Yes (Tuner/Monitor) S-Video in RGB in Scart2 AV in AV out S-Video in RGB in PC Monitor Input...
Page 24
Height (cm) Container Stuffing 1006 Sets/40' container w/Pallet w/Wrapping G-18 Material Cabinet Cabinet Front PC+ABS 94V0 NON-HALOGEN Cabinet Rear PS 94V0 NON-DECABROM Non-Halogen Eyelet G-19 Environment Environmental standard requirement Green procurement of TOSHIBA Pb- Free Phase3(PHASE3A) Measures for Whisker WEEE A3-5...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: POWER PCB AND TUER PCB (Refer to Fig. 1-3) AND P.C. BOARDS Disconnect the following connector: (CP501 and CP8101). Remove the 6 screws (1). CAUTION Remove the Power PCB in the direction of arrow (A). Be careful not to remove the FFC cable forcibly, Remove the screw (2).
DISASSEMBLY INSTRUCTIONS 1-5: DVD DECK (Refer to Fig. 1-5) Short circuit the position shown in Fig. 1-5 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. Remove the 4 screws (1). Remove the DVD Deck in the direction of arrow (A).
DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DVD DECK PARTS Check Hook NOTE Check Hook Check Hook 1. Disassemble only the DVD DECK PARTS parts listed here. Minute adjustments are needed if the disassembly is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y.
Page 28
DISASSEMBLY INSTRUCTIONS NOTE Traverse Ass'y When installing the Rack Feed Ass'y, push both ends to Check Hook align the teeth as shown Fig. 2-2-B. Then install it. In case of the Gear Motor installation, check if the value Check Hook of the Fig.
DISASSEMBLY INSTRUCTIONS When IC starts moving back and forth easily after REMOVAL AND INSTALLATION OF desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 3-3.) REMOVAL NOTE Put Masking Tape (cotton tape) around the Flat Package...
Page 30
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 3-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition.
SERVICING FIXTURES AND TOOLS Ref. No. Part No. Parts Name Remarks JG176 Up-Date Disc JG176 APJG176142 Up-Date Disc Up-Date of the Firmware RE-WRITE FOR DVD FIRMWARE Turn on the power, and set the DVD mode. Confirm that the "No Disc" will be appeared on the screen. Press both VOL.
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0".
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE FUNCTION FUNCTION OSD H POSI V POSI Read and perform these adjustments when repairing the OSD V POSI V POSI MAX circuits or replacing electrical parts or PCB assemblies. R DRIVE(N) V POSI MIN CAUTION R CUTOFF(N) BACKLIGHT CENTER G DRIVE(N)
Page 35
ELECTRICAL ADJUSTMENTS 2-2: CONTRAST MAX Receive the monoscope pattern. (RF Input) Using the remote control, set the brightness and contrast to normal position. Activate the adjustment mode display of Fig. 1-1 and press the channel button (35) on the remote control to select "CONTRAST MAX".
Page 36
ELECTRICAL ADJUSTMENTS 2-3: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (TUNER/AV/DVD) TUNER CVBS S(Y/C) FUNCTION STEP NO. OSD H POSI OSD V POSI R DRIVE(N) R CUT OFF(N) G DRIVE(N) G CUT OFF(N)
Page 37
ELECTRICAL ADJUSTMENTS 2-4: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment item is set correctly referring below. (TUNER/AV) AV1(SCART1) AV2(RCA) AV2(RCA) AV1(SCART1) TUNER CVBS CVBS S(Y/C) 576i 576i 480i 576i 480i 576i 480i 576i...
TROUBLESHOOTING GUIDE (LCD SECTION) POWER DOES NOT TURN ON Change F501. Is F501 broken? Check IC501 and peripheral Is there voltage at pin circuit. 6 of IC501 21V? Is R510 broken? Change R510. Change MAIN PCB.
Page 40
TROUBLESHOOTING GUIDE THE PICTURE APPEARS, BUT THE AUDIO DOES NOT APPEARS. (AT RF MODE) Connect CD301. Is CD301 connected? Is there signal at pins Change SP301 and SP302. 1 and 4 of CD301? Is there signal at pins 2 Check IC301 and peripheral and 4 of IC301? circuit.
Page 41
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR Is CD7005,CD7006 Does backlight shine? Connected CD7005,CD7006 connected ? Check IC7001 and Is the signal pin 16 peripheral circuit. and18 of IC7001 ? Is the voltage at pin Check F7001. 20 of IC7001 12V ? Is CD7204 connected? Connected CD7204.
Page 42
TROUBLESHOOTING GUIDE THE COLOR DOES NOT APPEAR Is setting of color Adjust the color. normal? Is the color signal Receive the color signal. received? Change MAIN PCB.
Page 43
TROUBLESHOOTING GUIDE (DVD SECTION) DOES NOT DISPLAY DVD PICTURE Does this display Check the disc. logo picture? Is there signal at pins Check pins 8 and 10 of 149 and 151 of CP8501 and peripheral circuit. IC4001? Does IC4001 gets P.CON+3.3V and Change IC4001.
Page 44
TROUBLESHOOTING GUIDE DISC DOES NOT EJECT Check pins 138 and 139 Does OSD appear Is remote key set of IC4001 and peripheral on the screen? effectively? circuit. Does this eject disc at Check IC4001 and Is there signal at pins 4 change DVD DECK? peripheral circuit.
Page 45
TROUBLESHOOTING GUIDE DOES NOT PLAY DVD Change DVD DECK. Is the voltage between Does CD2001 connect Does this display JG017 and JG018 less with CP2301 correctly? "INCORRECT DISC"? than 0.6V? Connect CD2301. Does this display Change IC4001. reading mark? Change DVD DECK. Does disc rotate? Change IC4001.
Page 46
TROUBLESHOOTING GUIDE DOES NOT PLAY CD Change DVD DECK. Is the voltage between Does CD2001 connect Does this display JG019 and JG018 less with CP2301 correctly? "INCORRECT DISC"? than 0.6V? Connect CD2301. Does this display Change IC4001. reading mark? Change DVD DECK. Does disc rotate? Change IC4001.
Page 47
TROUBLESHOOTING GUIDE NO SOUND DVD/CD ANALOG AUDIO Is there signal at pins 113, 114, 115 and Change IC4001. 116 of IC4001? Check pins 1 and 7 of IC8501 Is there signal at pins 1 and peripheral circuit. and 7 of IC8501? Does CD8501 connected? Connected CD8501.
Page 80
WAVEFORMS AUDIO/VIDEO 200μs 1.0V 200μs 1.0V 10μs 200mV 10μs 100mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
DVD DECK EXPLODED VIEW CD2001 M2602 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y. PCB640 (SW PCB ASS'Y) CD2301 Applying positions AA for the grease are displayed for this section. NOTE: CLASS MARK...