1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. TV DVD Combo
  5. 15DLV77C
  6. Service manual

Toshiba 15DLV77C Service Manual

15-inch diagonal lcd tv/dvd combination
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
15-inch Diagonal LCD TV/DVD
COMBINATION
The above model is classified as a green product (*1), as indicated by the underlined serial number.
This Service Manual describes replacement parts for the green product. When repairing this green
product, use the part(s) described in this manual and lead-free solder (*2).
For(*1) and (*2), see the next page.
©2007 Toshiba Corporation
15DLV77C
DOCUMENT CREATED IN JAPAN, June, 2007 GREEN
FILE NO. 810-200765GR

Advertisement

Table of Contents
loading

Related Manuals for Toshiba 15DLV77C

Summary of Contents for Toshiba 15DLV77C

  • Page 1 This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2). For(*1) and (*2), see the next page. ©2007 Toshiba Corporation DOCUMENT CREATED IN JAPAN, June, 2007 GREEN...
  • Page 2 Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.

  • Page 3: Important Safeguards

    Function setup Others ColorStream ® is a registered trademark of Toshiba America Consumer Products, L.L.C. is a trademark of Toshiba America Consumer Products, L.L.C. ©2007 Toshiba Corporation Before operating the unit, please read this manual thoroughly. *Screen size is approximate.

  • Page 4: Precautions

    Introduction (continued) IMPORTANT SAFEGUARDS 13. LIGHTNING 19. REPLACEMENT PARTS To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, When replacement parts are required, be sure the service technician uses replacement parts speciÀ ed by unplug it from the wall outlet and disconnect the antenna or cable system.

  • Page 5: Table Of Contents

    Because of problems and errors that can occur during the creation of DVD and CD Software and/or the manufacture of DVD and CD discs, Toshiba cannot assure that the DVD player contained in this TV will successfully play every disc bearing the DVD and CD logos.

  • Page 6: Identià Cation Of Controls

    Introduction IdentiÀ cation of controls (Continued) Inserting batteries Open the battery compartment Install two “R03/AAA” batteries Replace the compartment cover in the direction of the (supplied), paying attention to cover. Remote control arrow. the polarity indicated in the battery compartment. The instructions in this manual describe the function on the remote control.

  • Page 7: Connecting To Optional Equipment

    (component video). Connecting your TV/DVD to a component Note: Picture might be muted for some VCR playback. This is not a malfunction of this unit. ® video compatible DVD player, such as a Toshiba DVD player with ColorStream can greatly enhance picture quality and performance.

  • Page 8: Power Source

    Connections Connections Basic setup Power source Setting the language POWER This TV/DVD can display the on screen language in English, Spanish or French in the TV mode. Select the language you prefer À rst, then proceed with the other menu options. CANCEL ENTER Power connection...

  • Page 9: Closed Captions

    TV operation TV operation (Continued) Closed captions SLEEP WHAT IS CLOSED CAPTIONING? RECALL This television has the capability to decode and display closed captioned CH RTN television programs. Closed captioning will display text on the screen for MUTE hearing impaired viewers or it will translate and display text in another VOL +/–...

  • Page 10: Sound Control Adjustment

    TV operation Basic playback Sound control adjustment/ Playing a disc CANCEL This section shows you the basics on how to play a disc. Stereo and Second Audio Program (SAP) Sound controls are factory preset but you can adjust them individually as follows: / / / The TV/DVD is equipped with a feature known as multi-channel TV sound or MENU...

  • Page 11: Advanced Playback

    Advanced playback Zooming/Locating desired scene Repeat playback/A-B Repeat playback PLAY MODE 0–9 ZOOM ENTER JUMP PLAY CANCEL SKIP ENTER REPEAT A-B / / / RECALL Zooming Locating desired scene Repeat playback A-B Repeat playback This unit will allow you to zoom in on the frame image. Use the title, chapter and time recorded on the DVD disc A-B repeat playback allows you to repeat a section Press PLAY MODE during playback or stop...

  • Page 12: Changing Soundtrack Language

    Use of CD-RW for MP3 À les is not recommended. PLAY STOP You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission. MP3/WMA CD playback ® Audio CD/MP3/WMA/JPEG/DivX CD information Load a disc on which MP3 or WMA À...

  • Page 13: Repeat And Program Playback Using À Le Browser

    Advanced playback ® MP3/WMA/JPEG/DivX and Audio CD operation (Continued) STOP STOP TOP MENU DVD MENU You can select your desired JPEG À le on the À le menu and picture menu. / / / The selected JPEG À le is automatically adjusted to the TV screen. (When the aspect ratio of the JPEG À...

  • Page 14: Function Setup

    Function setup Customizing the function settings SETUP You can change the default settings of the DVD mode to customize ENTER performance to your preference. / / / RETURN Setting details Setting procedure Press SETUP during stop mode. Change the selection using , by Section Option...

  • Page 15: Temporary Cancel The Rating Level By Dvd Disc

    Function setup Customizing the function settings (Continued) Setting details Set the new password Parental E.B.L. : Off : Off : Off Menu E.B.L. Parental : Off : English : Off : Off TV Screen Set Password : 4:3 QSound Subtitle TV Screen Password : On...

  • Page 16: Troubleshooting

    Others Troubleshooting Use the following check list for troubleshooting when you have problems with your unit. Consult your local dealer or service outlet if problems persist. Be sure all connections are properly made when using with other units. SYMPTOMS POSSIBLE SOLUTIONS PAGE SYMPTOMS POSSIBLE SOLUTIONS...

  • Page 17: Limited Canada Warranty

    Dispute arises. To the extent not IMPLIED WARRANTIES, CONDITIONS AND REPRESENTATIONS Toshiba of Canada Limited (“TCL”) makes the following limited warranties to original consumers in Canada. THESE LIMITED precluded by law, no claim, dispute, controversy or disagreement of...
  • Page 18 CAUTION THIS LCD COLOR TELEVISION EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE- FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

  • Page 19: Important Service Safety Information

    IMPORTANT SERVICE SAFETY INFORMATION Safety precautions to be followed during servicing: Parts marked with an are critical parts for safety. Replace only with the one described in the parts list. Before returning the DVD product to the customer, make the appropriate leakage current check or resistance measurements to ensure that exposed parts are properly insulated from the supply circuit.

  • Page 20: Important Safeguards

    IMPORTANT SAFEGUARDS READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating and use instructions should be followed.
  • Page 21 IMPORTANT SAFEGUARDS (CONTINUED) OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
  • Page 22 EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING NEC-NATIONAL ELECTRICAL CODE ELECTRODE SYSTEM (NEC ART 250, PART H) S2898A A1-5...

  • Page 23: When Replacing Dvd Deck

    WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD MT PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector.

  • Page 24: Disc Removal Method At No Power Supply

    DISC REMOVAL METHOD AT NO POWER SUPPLY Remove the Back Cabinet and Angle Deck. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) Slide the Belt Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1) Take out the Disc from the DVD Deck.
  • Page 25 TABLE OF CONTENTS • GREEN PRODUCT PROCUREMENT • LEAD-FREE SOLDER • OWNER'S MANUAL A1-1 CAUTION ........................A1-2 IMPORTANT SERVICE SAFETY INFORMATION ............. A1-3~A1-5 IMPORTANT SAFEGUARDS ..................A1-6 WHEN REPLACING DVD DECK ................A1-7 DISC REMOVAL METHOD AT NO POWER SUPPLY ..........A1-7 PARENTAL CONTROL - RATING LEVEL ..............
  • Page 26 GENERAL SPECIFICATIONS LCD Size / Visual Size 15.0 inch / 380.0mmV LCD Type Color TFT LCD System Number of Pixels 1024(H) x 768(V) View Range Left/Right 70/70 degree Up/Down 60/65 degree Color System NTSC Speaker 2 Speaker Position Front Size 1.5 x 2.7 inch Impedance 8 ohm...
  • Page 27 GENERAL SPECIFICATIONS Regulation Safety cUL(E650065_00) Radiation Laser Operation Temperature C ~ +40 Storage C ~ +60 Operating Humidity Less than 80% RH Clock and Clock Timer Sleep Timer Max Time 120 Min Step 10 Min On Timer Program Off Timer Program Wake Up Timer Timer Back-up (at Power Off Mode)
  • Page 28 GENERAL SPECIFICATIONS Zoom/ Quick View Mute Eject Sleep Jump Game Freeze frame G-11 Features Auto Shut Off (TV) Auto Search Power On Memory Comb Filter Game Position Auto Setup(Language/CH Program) Picture Setting Picture Preference Brightness , Contrast , Color Tint Sharpness Color Temperature Cable Clear...
  • Page 29 GENERAL SPECIFICATIONS 720×576i (16:9) 720×576p (4:3) 720×576p (16:9) 1280×720p 1920×1080i Features Tray Lock (DVD) JPEG Video CD Playback SVCD Playback Overlay Graphics And Text Command List Entry Point Jump MP3 Playback Divx Playback DMF Support Digital Out (Dolby Digital) (MPEG) (PCM) (DTS) Down Mix Out...
  • Page 30 Container Stuffing (40' container) Sets/40' container G-17 Material Cabinet Front PS 94V0 DECABROM Rear PS 94V0 DECABROM Jack Panel Non-Halogen Demand Eyelet Demand Environmental standard requirement (by buyer) Green procurement of TOSHIBA G-18 Environment Pb-free Phase3 (Phase3A) Measures for Whisker A3-5...

  • Page 31: General Specifications

    GENERAL SPECIFICATIONS G-19 AC Power Adapter Provided Accessories Power Requirement AC 120V 60Hz Max Power Consumption (Adapter Only) at AC 65 W DC Output DC Jack : DC12V 4.5A Dimension Approx. W x D x H (mm) 150 x 72 x 43 Weight Approx.

  • Page 32: Disassembly Instructions

    DISASSEMBLY INSTRUCTIONS 1-3: ANGLE BACK (Refer to Fig. 1-3) 1. REMOVAL OF MECHANICAL PARTS Remove the 3 screws 1. AND P.C. BOARDS Remove the Angle Back in the direction of arrow. 1-1: HINGE ASS'Y (Refer to Fig. 1-1) Remove the 3 screws 1. Remove the Stand in the direction of arrow (A).
  • Page 33 DISASSEMBLY INSTRUCTIONS NOTE Before your operation, please read “PREPARATION OF SERVICING”. Shield FFC Use the Lead Free solder. Manual soldering conditions Shield MPEG • Soldering temperature: 320 ± 20˚C DVD MT PCB • Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu When Soldering/Removing of solder, use the drawing CP203 CP4203...
  • Page 34 DISASSEMBLY INSTRUCTIONS 1-8: SIDE JACK PCB (Refer to Fig. 1-8) OPERATION PCB/REMOCON PCB (Refer 1-10: to Fig. 1-10) Disconnect the following connectors: (CP301, CP4402 and CP4403). Disconnect the following connector: (CP2251). Remove the 2 screws 1. Remove the 2 screws 1. Remove the Side Jack PCB in the direction of arrow (A).
  • Page 35 DISASSEMBLY INSTRUCTIONS 1-11: LCD COVER/LCD PANEL (Refer to Fig. 1-11) Remove the 2 screws 1. Remove the 2 screws 2. Remove the Angle Hinge in the direction of arrow (A). Remove the 8 screws 3. Remove the LCD Cover in the direction of arrow (B). Remove the 4 screws 4.

  • Page 36: Removal Of Dvd Deck Parts

    DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DVD DECK PARTS Check Hook NOTE Check Hook 1. Disassemble only the DVD DECK PARTS parts listed here. Minute adjustments are needed if the disassembly is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y. 2-1: TRAVERSE ASS'Y (Refer to Fig.
  • Page 37 DISASSEMBLY INSTRUCTIONS NOTE Traverse Ass'y When installing the Rack Feed Ass'y, push both ends to Check Hook align the teeth as shown Fig. 2-2-B. Then install it. In case of the Gear Motor installation, check if the value Check Hook of the Fig.

  • Page 38: Removal And Installation Of Flat Package Ic

    DISASSEMBLY INSTRUCTIONS 3. REMOVAL AND INSTALLATION OF FLAT 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using PACKAGE IC a tweezers and remove the IC by moving with the IC REMOVAL desoldering machine.
  • Page 39 DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- 1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 3-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.

  • Page 40: Service Mode List

    SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition.

  • Page 41: Servicing Fixtures And Tools

    SERVICING FIXTURES AND TOOLS Ref. No. Remarks Part No. Parts Name JG176 Up-Date Disc JG176 APJG176098 Up-Date Disc Up-Date of the Firmware RE-WRITE FOR DVD FIRMWARE Turn on the power, and set the DVD mode. Confirm that the “No Disc” will be appeared on the screen. Press both VOL.

  • Page 42: Confirmation Of Check Sum

    WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0".
  • Page 43 ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE FUNCTION FUNCTION Read and perform these adjustments when repairing the H POSI OSD BAK LIGHT CENT V POSI OSD BAK LIGHT MAX circuits or replacing electrical parts or PCB assemblies. R DRIVE(N) BAK LIGHT MIN CAUTION R CUT OFF(N) BRIGHT CENT...
  • Page 44 ELECTRICAL ADJUSTMENTS 2-2: WHITE BALANCE Place the set in Aging Test for more than 15 minutes. Receive the gray scale pattern from the Pattern Generator. Using the remote control, set the brightness and contrast to normal position. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "R DRIVE(N)".
  • Page 45 ELECTRICAL ADJUSTMENTS 2-4: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each of the adjustment items are set correctly referring below. (TV/AV/CS/GAME/DVD) 480i 480p GAME FUNCTION Step No. Step No. Step No. Step No. Step No. Step No.

  • Page 46: Dvd

    ELECTRICAL ADJUSTMENTS 3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) LCD PANEL DVD DECK DVD MT PCB CP2303 CD2301 CP2302 CD2001 CP2301 CD7201 CD702 CD501 CD703 BACK LIGHT PCB SCALER PCB CP202 CP7003 CP7001 CP7201 CD7001 REMOCON PCB CP203 CP2204 CP7004 CP3201 CP204...
  • Page 47 TROUBLESHOOTING GUIDE (LCD SECTION) POWER DOES NOT TURN ON CHANGE F3801. IS F3801 BROKEN ? IS THERE VOLTAGE CHECK Q3809 AND AT PIN 7 OF Q3809 PERIPHERAL CIRCUIT. 5V ? IS THERE VOLTAGE CHECK IC3806 AND AT PIN 3 PIN OF PERIPHERAL CIRCUIT.
  • Page 48 TROUBLESHOOTING GUIDE THE PICTURE APPEARS, BUT THE AUDIO DOES NOT APPEAR. (AT RF MODE) IS CP4403 AND CONNECT CP4403 AND CP4401 CP4401. CONNECTED ? IS THERE SIGNAL AT CHANGE SP301. PINS 1 AND 4 OF CP4403 ? IS THERE SIGNAL AT CHECK IC302 AND PINS 2 AND 4 OF PERIPHERAL CIRCUIT.
  • Page 49 TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (1). CHECK THE CONNECTED OF CP3802 AND THE VOLTAGE DOES BACK LIGHT SHINE ? PF PINS 1~3. CONNECT CD7201. IS CD7201 CONNECTED ? IS THERE SIGNAL AT PINS 5, 6, 8, 9, 11, 12, CHANGE V2301.
  • Page 50 TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (2). CHANGE IC4201 AND IS THERE SIGNAL AT PERIPHERAL CIRCUIT. PIN 31 OF IC4201 ? CONNECT CD4204, IS CD4204 CONNECTED CHANGE IC4201 AND AND IS THERE SIGNAL AT PERIPHERAL CIRCUIT. PINS 1, 3 AND 5 ? CHANGE IC801 AND IS THERE SIGNAL PERIPHERAL CIRCUIT.
  • Page 51 TROUBLESHOOTING GUIDE THE COLOR DOES NOT APPEAR. IS SETTING OF CHANGE THE SETTING OF COLOR NORMAL ? COLOR. IS THE COLOR RECEIVE THE COLOR SIGNAL. SIGNAL RECEIVED ? IS THERE COLOR CHECK IC801 AND SIGNAL AT PINS 13 PERIPHERAL CIRCUIT. AND 31 OF IC801? CHANGE SCALER PCB.
  • Page 52 TROUBLESHOOTING GUIDE ON SCREEN DISPLAY DOES NOT APPEAR. IS THERE SIGNAL AT CHECK IC101 AND PINS 2, 3, 4 AND 5 OF PERIPHERAL CIRCUIT. IC101 ? IS THERE SIGNAL AT CHECK NR801 AND PINS 57, 58, 59 AND 60 PERIPHERAL CIRCUIT. OF IC801 ? CHECK IC801 AND PERIPHERAL CIRCUIT.
  • Page 53 TROUBLESHOOTING GUIDE (DVD SECTION) DOES NOT DISPLAY DVD PICTURE DOES THIS DISPLAY CHECK THE DISC. LOGO PICTURE ? DOES THIS HAVE SIGNAL CHECK PINS 9 AND 7 OF AT PINS 151 AND 153 OF CD703 AND PERIPHERAL IC4001 ? CIRCUIT. DOES IC4001 GETS CHANGE IC4001.
  • Page 54 TROUBLESHOOTING GUIDE DISC DOES NOT EJECT. CHECK PINS 29 AND 30 OF IS REMOTE KEY SET DOES OSD APPEAR IC101 AND PERIPHERAL EFFECTIVELY ? ON THE SCREEN ? CIRCUIT. CHECK PINS 205 AND 206 OF IC4001 AND PERIPHERAL CIRCUIT. DOES THIS HAVE DOES THIS EJECT CHECK IC2301 AND SIGNAL AT PINS 4...
  • Page 55 TROUBLESHOOTING GUIDE DOSE NOT PLAY DVD. CHANGE DVD DECK. DOES CD2001 IS THEVOLTAGE DOES THIS DISPLAY CONNECT WITH CP2301 BETWEEN JG017 AND "INCORRECT DISC". CORRECTLY ? JG018 LESS THAN 0.6V ? CONNECT CD2301. DOES THIS DISPLAY CHANGE IC4001. READING MARK ? CHANGE DVD DECK.
  • Page 56 TROUBLESHOOTING GUIDE DOES NOT PLAY CD. CHANGE DVD DECK. DOES CD2001 IS THE VOLTAGE DOES THIS DISPLAY CONNECT WITH CP2301 BETWEEN JG019 AND "INCORRECT DISC". CORRECTLY ? JG018 LESS THAN 0.6V ? CONNECT CD2301. DOES THIS DISPLAY CHANGE IC4001. READING MARK ? CHANGE DVD DECK.
  • Page 57 TROUBLESHOOTING GUIDE NO SOUND DVD/CD ANALOG AUDIO. DOES THIS HAVE SIGNAL AT PINS 3 AND REFER TO "LCD SECTION". 5 OF CD703 ? CHECK PINS 7 AND 8 OF DOES THIS HAVE IC8502 AND PERIPHERAL SIGNAL AT PINS 7 AND CIRCUIT.
  • Page 62 R215...
  • Page 63 C4257 L4203 W010 W825 C4250 W025 C2205 L4206 W826 W004 W003 W002 W829 W805 W001 W008 W831 W009 W007 R3802 W012 W028 C3839 W853 C3842 D3802 D3810 C3805 W029 W039 W040 F3801 L3804 C3825 L3801 W834 W036 W034 W836 C3810 W035 W837 R3815...
  • Page 87 WAVEFORMS JACK AV SWITCH 50μs 1.0V 200mV 0.5V SOUND 200mV 0.5V 50mV TUNER/STEREO 10μs 0.5V 200mV 50mV 200mV 200mV 0.5V 0.5ms 0.5V 1.0V 200mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.

  • Page 88: Mpeg/Micon/Dsp/Rf_Amp

    WAVEFORMS MICON SOUND 20μs 50ns 500mV 500mV 50mV SCALER 20μs 10μs 500mV 100mV 50mV MPEG/MICON/DSP/RF_AMP 20μs 10μs 500mV 10ns 200mV 100mV 10μs 10μs 2.0V 100mV 20mV LVDS 10ms 20μs 100mV 500mV 20ns 1.0V NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.

  • Page 89: Regulator 2

    WAVEFORMS 10μs 200ns 10μs 2.0V 1.0V 200mV MEMORY REGULATOR 2 10μs 2μs 2.0V 2.0V 500mV AUDIO/VIDEO 2μs 10μs 500μs 2.0V 5.0V 500mV INVERTER 10μs 10μs 500μs 2.0V 5.0V 500mV 10μs 10μs 10μs 2.0V 50.0V 200mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
  • Page 90 WAVEFORMS 10μs 10μs 50.0V 500V 10μs 10μs 500V 50.0V 10μs 50.0V 10μs 500V 10μs 500V NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.

  • Page 91: Mechanical Exploded Views

    MECHANICAL EXPLODED VIEW 103C 103D 103B 103A PCBDA0 (REMOCON PCB ASS'Y) PCB270 (OPERATION PCB ASS'Y) PCB280 (OPERATION 2 PCB ASS'Y) 101C 101B 101I 101F 101J 101D 101G 101E 101I NOTE: 153 is not included in Front cabi Ass'y. 101E 101H 101J 101A J1-1...
  • Page 92 MECHANICAL EXPLODED VIEW 102D NOTE: 104 is not included in Stand Ass'y. 102C 102C 102C 102E 102E 102C PCBDS0 (SCALER PCB ASS'Y) 102B 102A PCB130 (DVD MT PCB ASS'Y) PCBD90 (SIDE JACK PCB ASS'Y) PCBD20 (AV PCB ASS'Y) PCB350 (BACK LIGHT PCB ASS'Y) J1-2...
  • Page 93 MECHANICAL EXPLODED VIEW (PACKING DIAGRAM) CD3811 TM101 AD001 149, 150, 151, 152 BL001 J1-3...

  • Page 94: Dvd Deck Exploded View

    DVD DECK EXPLODED VIEW CD2001 M2602 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y. PCB640 (SW PCB ASS'Y) CD2301 NOTE: Applying positions AA for the grease are displayed for this section. CLASS MARK Check if the correct grease is applied for each position.

  • Page 95: Mechanical Replacement Parts List

    MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description AE009346 7A701A979A FRONT CABI ASS'Y 101A AE009347 701WPJD526 CABINET FRONT 101B AE008446 702WPA1240 COVER HINGE 101C AE008447 713WPAA246 GLASS LED 101D AE004502 7235490047 BADGE BRAND 101E AE008448 735WPE0057 BUTTON CAP 101F AE008449 738WPA0208...
  • Page 96 MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description AE009349 723000D690 SHEET BARCODE AE002901 791WHDA001 LAMIFILM BAG AE008488 792WHA0666 PACKAGE TOP AE008489 792WHA0667 PACKAGE BOTTOM AE008490 792WHA0683 PACKAGE PAD AE008491 792WHA0687 PACKAGE PAD AE009350 793WCDD569 GIFT BOX AE008493 795WCAA496 AE007894 797WCA0040...

  • Page 97: Dvd Deck Replacement Parts List

    DVD DECK REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description ! 600 AE009353 A5X002B650 DVD MECHA ASS'Y A5X002B650 AE008499 92SBB0033A LOADER SUB ASS'Y DLM1D29-31 AE005815 92AAA0017A FEED RACK ASS'Y AE003551 92P100088A GEAR,MOTOR AE005805 92P100117A GEAR,MIDDLE AE008500 92P200017A INSULATOR, F AE008501 92P200018A INSULATOR, R...

  • Page 98: Electrical Replacement Parts List

    ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description RESISTORS ! R3805 BZ210191 R3X28B010J R,METAL OXIDE OHM 3W CAPACITORS C339 AE006603 E61FF3102D 1000 UF 25V C3805 AE008429 E61FF2102D 1000 UF 16V D IODES D102 AE004795 DE7RB5R62B DIODE ZENER UDZS5.6B TE-17 D103 AE004795...
  • Page 99 ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description TRANSISTORS Q203 BZ510109 TCAA3875SY TRANSISTOR SILICON KTC3875S_Y_RTK Q204 BZ510067 TNAAC05002 COMPOUND TRANSISTOR KRC103SRTK Q205 BZ510092 TPAAD05003 COMPOUND TRANSISTOR KRA104SRTK Q206 BZ510108 TAAA1504SY TRANSISTOR SILICON KTA1504S_Y_RTK Q207 BZ510109 TCAA3875SY TRANSISTOR SILICON KTC3875S_Y_RTK Q208 BZ510109...
  • Page 100 ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description COILS &TRANSFORMERS L7202 AE005285 0216S8470K COIL L7203 AE005285 0216S8470K COIL L8502 AE000828 02167F1R0K COIL L8503 AE000828 02167F1R0K COIL T7001 AE008397 048110002H TRANSFORMER,SWITCHING CRT-057 T7002 AE008397 048110002H TRANSFORMER,SWITCHING CRT-057 T7003 AE008397 048110002H TRANSFORMER,SWITCHING...
  • Page 101 ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description MISCELLANEOUS B4014 AE005476 0246C51024 CORE,BEADS MMZ1608R102CT B4015 AE005476 0246C51024 CORE,BEADS MMZ1608R102CT B4016 AE005476 0246C51024 CORE,BEADS MMZ1608R102CT B4018 AE005476 0246C51024 CORE,BEADS MMZ1608R102CT B4201 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0 B4202 AE008395 024HC56005 CORE,BEADS FCM1608CF-600T06 B4203...
  • Page 102 ELECTRICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description MISCELLANEOUS X101 AE004780 100WT01611 CRYSTAL HC-49/U-S X801 AE007784 100YT05401 CRYSTAL FCX-03 X4001 AE008161 100GT02720 CRYSTAL B27000C005 RESISTOR RC....CARBON RESISTOR CAPACITORS CC....CERAMIC CAPACITOR CE....ALUMI ELECTROLYTIC CAPACITOR CP....POLYESTER CAPACITOR CPP....
  • Page 103 TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN...

Table of Contents