Sharpness; Noise Reduction; System Selector; Adjusting The Position - Panasonic PT PT-DW5100EL Operating Instructions Manual

SHARPNESS

"SHARPNESS" is used to adjust the crispness of
the image.
: Sharpens the edge of the image.
: Softens the edge of the image.

NOISE REDUCTION

In this mode, the video noise is reduced.
OFF : No correction
1 : Low
2 : Middle
3 : High
AI
Gray scale control is exercised to suit the images,
and optimal images with a clear contrast are
projected.
ON : AI compensation is enabled.
OFF : AI compensation is disabled.

SYSTEM SELECTOR

Set this according to the connected signal system.
(S-Video/Video terminal input signal)
AUTO : This is the standard setting. The
received signal system is automatically
identified.
AUTO NTSC
PAL60 SECAM
• When signal deterioration or other
Note
factors prevent images from being
displayed correctly with the "AUTO"
setting, change the setting to match
the connected signal system.
(RGB1/RGB2 terminal input signals)
AUTO : This is the standard setting. The
received signal system is automatically
identified.
When VGA60/480p signals are input
AUTO VGA60
YC C 480pRGB
B R
When other than VGA60/480p are input
AUTO RGB
YP P (YC C )
B R B R
For the signals which are supported, refer to page
61.
NTSC4.43 PAL
PAL-N PAL-M

Adjusting the position

POSITION

SHIFT

ASPECT

ZOOM
CLOCK PHASE
KEYSTONE
MENU SELECT
SUB MENU
SHIFT
The position where the images are displayed can be moved here.
: The position is moved horizontally.
: The position is moved vertically.
ASPECT
AUTO : (For S-Video/Video signals only)
At this setting, when S1 video signals*
identified as being input to the S-Video
connector or video ID signals are identified
as being input to the video connector, the
images are displayed after automatically
being converted to the 16:9 aspect ratio.
16:9 : At this setting, when standard signals*
input, the images are converted to the 16:9
aspect ratio and displayed. When wide-screen
signals* 3 are input, the images are displayed
with their inherent aspect ratio intact.
4:3 : At this setting, when standard signals*
the images are displayed with their inherent aspect
ratio intact. When wide-screen signals*
they are converted by the PT-D5700E/PT-
D5700EL to the 4:3 aspect ratio and displayed.
With the PT-DW5100E/PT-DW5100EL, the images
are reduced in size and displayed without
converting their aspect ratio so that they will fit onto
a screen with a 4:3 aspect ratio.
S4:3 : Select this setting when using a 16:9 screen.
H FIT : Pictures are displayed using all the panel
pixels in the horizontal direction. When a
signal has an aspect ratio taller than that of
the panel pixel*
with the top and bottom portions cut off.
V FIT : Pictures are displayed using all the panel
pixels in the vertical direction. When a signal
has an aspect ratio wider than that of the
panel pixel* , the image will be displayed with
4
the left and right sides cut off.
HV FIT : The image is displayed on all the panel
pixels* . When the aspect ratio of the input
4
signal is different from that of the panel
pixel* , the signal is transformed to the aspect
4
ratio of the panel pixel*
* S1 video signals are 16:9 video signals to which is added the detection signal
1
output from the video deck or other unit which supports the wide-screen format.
* 2 Here, the standard signal means 4:3 or 5:4 input signals.
* 3 Here, the wide-screen signals means 16:9, 15:9 or 15:10 input signals
* 4 Panel pixel aspect ratio is 4:3 in the case of PT-D5700E/PT-D5700EL
and 15:9 for PT-DW5100E/PT-DW5100EL.
• If you choose an aspect ratio that does not
Attention
match the source video's aspect ratio, you
will see a picture with an aspect ratio not the
same as that of the original picture. Choose
the appropriate aspect ratio carefully to
match that of the original picture.
4:3
+16
are
1
2 are
are input,
2
3 are input,
4 , the image will be displayed
and then displayed.
4
(Continued on the next page)
29