Toyota 2012 Camry Hybrid Owner's Manual

Toyota 2012 Camry Hybrid Owner's Manual

Hide thumbs Also See for 2012 Camry Hybrid:

Advertisement

Abbreviation list
Abbreviation/Acronym list
ABBREVIATIONS
A/C
ABS
ACC
ALR
BSM
CRS
DISP
ECU
EDR
ELR
EPS
GAWR
GVWR
I/M
LATCH
LED
M + S
MMT
MTBE
OBD
SRS
TIN
TPMS
TRAC
VIN
VSC
520
MEANING
Air Conditioning
Anti-lock Brake System
Accessory
Automatic Locking Retractor
Blind Spot Monitor
Child Restraint System
Display
Electronic Control Unit
Event Data Recorder
Emergency Locking Retractor
Electric Power Steering
Gross Axle Weight Ratings
Gross Vehicle Weight Rating
Emission inspection and maintenance
Lower Anchors and Tethers for Children
Light Emitting Diode
Mud and Snow
Methylcyclopentadienyl Manganese Tricarbonyl
Methyl Tertiary Butyl Ether
On Board Diagnostics
Supplemental Restraint System
Tire Identification Number
Tire Pressure Warning System
Traction Control
Vehicle Identification Number
Vehicle Stability Control

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2012 Camry Hybrid and is the answer not in the manual?

Questions and answers

Summary of Contents for Toyota 2012 Camry Hybrid

  • Page 1 Abbreviation list Abbreviation/Acronym list ABBREVIATIONS MEANING Air Conditioning Anti-lock Brake System Accessory Automatic Locking Retractor Blind Spot Monitor Child Restraint System DISP Display Electronic Control Unit Event Data Recorder Emergency Locking Retractor Electric Power Steering GAWR Gross Axle Weight Ratings GVWR Gross Vehicle Weight Rating Emission inspection and maintenance...
  • Page 2: For Your Information

    Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available on the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
  • Page 3 ● SRS airbag system ● Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system. High voltage parts and cables on the hybrid vehicles emit approximately the...
  • Page 4 ● Usage of data collected through Safety Connect (U.S.mainland only) If your Toyota has Safety Connect and if you have subscribed to those ser- vices, please refer to the Safety Connect Telematics Subscription Service Agreement for information on data collected and its usage.
  • Page 5 Event data recorder This vehicle is equipped with an event data recorder (EDR). The main pur- pose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
  • Page 6 ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehicle) is obtained • In response to an official request by the police, a court of law or a govern- ment agency •...
  • Page 7 In the event that your vehicle must be disposed of, the hybrid battery must be disposed of by your Toyota dealer or a qualified service shop. If the hybrid battery is not disposed of properly, it...
  • Page 8 This is a warning against something which, if ignored, may cause damage to the vehicle or its equipment. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.
  • Page 9 TABLE OF CONTENTS Information on the hybrid system and adjusting and Before driving operating features such as door locks, mirrors, and steering column. When driving Driving, stopping and safe-driving information. Interior fea- Air conditioning and audio systems, as well as other in- tures terior features for a comfortable driving experience.
  • Page 10 1-1. Hybrid system Hybrid system Your vehicle is a hybrid vehicle. It has characteristics different from conventional vehicles. Be sure you are closely familiar with the char- acteristics of your vehicle, and operate with care. The hybrid system combines the use of a gasoline engine and an electric motor (traction motor) according to driving conditions, improving fuel efficiency and reducing exhaust emissions.
  • Page 11 1-1. Hybrid system ■ During normal driving The gasoline engine is predominantly used. The electric motor (traction motor) charges the hybrid battery as necessary. ■ When accelerating sharply The power of the hybrid battery (traction battery) is added to that of the gasoline engine via the electric motor (traction motor).
  • Page 12 1-1. Hybrid system ■ Regenerative braking In the following situations, kinetic energy is converted to electric energy and deceleration force can be obtained in conjunction with the recharging of the hybrid battery (traction battery). ● The accelerator pedal is released. ●...
  • Page 13 After the 12-volt battery has discharged or has been changed or removed The gasoline engine may not stop even if the vehicle is running on the hybrid battery (traction battery). If this continues for a few days, contact your Toyota dealer.
  • Page 14 When in the area surrounding the rear of the vehicle, rather than in front of the vehicle ■ Maintenance, repair, recycling, and disposal Contact your Toyota dealer regarding maintenance, repair, recycling and dis- posal. Do not dispose of the vehicle yourself.
  • Page 15 1-1. Hybrid system Hybrid system precautions Take care when handling the hybrid system, as it contains a high voltage system (about 650V at maximum) as well as parts that become extremely hot when the hybrid system is operating. Obey the caution labels attached to the vehicle. Air conditioning compressor Service plug Power control unit with DC/...
  • Page 16 If the emergency shut off system activates, your vehicle will not restart. To restart the hybrid system, contact your Toyota dealer. Hybrid warning message A message is automatically displayed when a malfunction occurs in the hybrid system or an improper operation is attempted.
  • Page 17 If a warning light comes on, a warning message is displayed, or the 12- volt battery has been disconnected The hybrid system may not start. In that case, try to start the system again. If the “READY” indicator does not come on, contact your Toyota dealer. ■ Running out of fuel...
  • Page 18 1-1. Hybrid system CAUTION ■ High voltage precautions The vehicle has high voltage DC and AC systems as well as a 12-volt sys- tem. DC and AC high voltage is very dangerous and can cause severe burns and electric shock that may result in death or serious injury. ●...
  • Page 19 1-1. Hybrid system CAUTION ■ Road accident cautions Observe the following precautions to reduce the risk of death or serious injury: ● Pull your vehicle off the road, shift the shift lever to P, apply the parking brake, and turn the hybrid system off. ●...
  • Page 20 1-1. Hybrid system NOTICE ■ Hybrid battery air vent ● Do not place foreign objects over or in front of the air vent. The hybrid bat- tery (traction battery) may overheat and be damaged. ● Clean the air vent regularly to prevent the hybrid battery (traction battery) from overheating.
  • Page 21 1-1. Hybrid system Energy monitor/consumption screen You can view the status of your hybrid system on the multi-informa- tion display and the navigation system or Display Audio system. Navigation system equipped) or Display Audio system (if equipped) Multi-information display Energy monitor Navigation system (if equipped) Press “INFO APPS”.
  • Page 22 1-1. Hybrid system Display Audio system (if equipped) Press “CAR”. If the “Trip Information” or “Past Record” screen displayed, touch “Energy”. Multi-information display Push the “DISP” switch on the steering wheel several times to select the energy monitor dis- play. (→P. 185) Navigation system or Multi-information Display Audio system...
  • Page 23 1-1. Hybrid system Navigation system or Multi-information Display Audio system display Navigation system When the vehi- cle is powered by the gasoline Display Audio system engine Navigation system When the vehi- cle is powered by both the gas- oline engine and Display Audio system the electric motor (traction...
  • Page 24 1-1. Hybrid system Navigation system or Multi-information Display Audio system display Navigation system When the vehi- cle is charging the hybrid bat- Display Audio system tery (traction battery) Navigation system When there is no energy flow Display Audio system...
  • Page 25 1-1. Hybrid system Navigation system or Multi-information Display Audio system display Navigation system Hybrid battery Full (traction bat- Display Audio system tery) status Full Full...
  • Page 26 1-1. Hybrid system Trip Information screen (Navigation system or Display Audio system) Navigation system STEP Press “INFO APPS”. (→P. 39) STEP Touch “Fuel Consumption” on the information screen. STEP If “Energy Monitor” screen is displayed, touch “Fuel Con- sumption”. If “Past Record” screen is displayed, touch “Trip Information”. Fuel consumption in the past 15 minutes Displays the average vehicle...
  • Page 27 1-1. Hybrid system Display Audio system Press “CAR”. (→P. 39) If the “Energy Monitor” or “Past Record” screen is displayed, touch “Trip Information”. Fuel consumption in the past 15 minutes Displays the average vehicle speed since the hybrid system was started. Displays the elapsed time since the hybrid system was started.
  • Page 28 1-1. Hybrid system Past record screen (Navigation system or Display Audio system) Navigation system STEP Press “INFO APPS”. (→P. 39) STEP Touch “Fuel Consumption” on the information screen. STEP If “Energy Monitor” screen is displayed, touch “Fuel Con- sumption”. If “Trip Information” screen is displayed, touch “Past Record”. Best past fuel consumption Update The average fuel consumption...
  • Page 29 1-1. Hybrid system Display Audio system Press “CAR”. (→P. 39) If the “Energy Monitor” or “Trip Information” screen is displayed, touch “Past Record”. Best past fuel consumption Update The average fuel consumption and graph are updated, and a new average fuel consumption record begins.
  • Page 30 1-1. Hybrid system Hybrid vehicle driving tips For economical and ecological driving, pay attention to the following points: ■ Using Eco drive mode (→P. 170) ■ Use of the Hybrid System Indicator More Eco-friendly driving is possible by keeping the Hybrid System Indicator needle within the Eco area.
  • Page 31 1-1. Hybrid system ■ Checking tire inflation pressure Make sure to check the tire inflation pressure frequently. Improper tire inflation pressure can cause poor fuel consumption. Also, as snow tires can cause large amounts of friction, their use on dry roads can lead to poor fuel consumption.
  • Page 32 1-2. Key information Keys The following keys are provided with the vehicle. Electronic keys • Operating the smart key system (→P. 53) • Operating wireless remote control function (→P. 66) Mechanical keys Key number plate Using the mechanical key To take out the mechanical key, push the release button and take the key out.
  • Page 33 Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a mechanical key is lost, a new key can be made at your Toyota dealer using the key number plate. (→P. 457) ■...
  • Page 34 Take your vehicle with all the electronic keys provided with your vehicle to your Toyota dealer. ■ When a vehicle key is lost If the key remains lost, the risk of vehicle theft increases significantly. Visit your Toyota dealer immediately with all remaining electronic keys that was provided with your vehicle.
  • Page 35 1-3. Opening, closing and locking the doors and trunk Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) Electronic key Electronic key Electronic key...
  • Page 36 1-3. Opening, closing and locking the doors and trunk Unlocking and locking the doors (front door handles only) Grip the driver’s door handle to unlock the door.* (Grip the pas- senger’s door handle to unlock all doors.) Make sure to touch the sensor on the back of the handle.
  • Page 37 1-3. Opening, closing and locking the doors and trunk Antenna location and effective range ■ Antenna location Antennas outside the cabin Antenna outside the trunk Antenna inside the trunk Antennas inside the cabin...
  • Page 38 1-3. Opening, closing and locking the doors and trunk ■ Effective range (areas within which the electronic key is detected) When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the front outside door handles.
  • Page 39 1-3. Opening, closing and locking the doors and trunk ■ When the door cannot be locked by the lock sensor Use your palm to touch the lock sensor. ■ Alarms and warning indicators A combination of exterior and interior alarms as well as warning messages shown on the multi-information display is used to prevent theft of the vehicle and accidents resulting from erroneous operation.
  • Page 40 1-3. Opening, closing and locking the doors and trunk ■ Security feature If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again. (How- ever, depending on the location of the electronic key, the key may be detected as being in the vehicle.
  • Page 41 1-3. Opening, closing and locking the doors and trunk ■ Battery-saving function The battery-saving function will be activated in order to prevent the elec- tronic key battery and the 12-volt battery from being discharged while the vehicle is not in operation for a long time. ●...
  • Page 42 1-3. Opening, closing and locking the doors and trunk ■ Conditions affecting operation The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and engine immobilizer system from operating properly.
  • Page 43 1-3. Opening, closing and locking the doors and trunk ■ Notes for the entry function ● Even when the electronic key is within the effective range (detection areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
  • Page 44 1-3. Opening, closing and locking the doors and trunk ■ Notes for locking the doors ● Touching the door lock sensor while wearing gloves may delay or prevent lock operation. Remove the gloves and touch the lock sensor again. ● When the lock operation is performed using the lock sensor, recognition signals will be shown up to two consecutive times.
  • Page 45 1-3. Opening, closing and locking the doors and trunk ■ When the vehicle is not driven for extended periods ● To prevent theft of the vehicle, do not leave the electronic key within 6 ft. (2 m) of the vehicle. ●...
  • Page 46 Starting the hybrid system and changing “POWER” switch modes: →P. 459 Stopping the hybrid system: →P. 159 ● ■ Customization that can be configured at Toyota dealer Settings (e. g. smart key system) can be changed. (Customizable features: →P. 498) ■ Certification for the smart key system U.S.A.
  • Page 47 (→P. 55) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves.
  • Page 48 5 seconds unlocks the other doors. Opens the driver’s window and moon roof (press and hold) Unlocks the trunk (press and hold) Sounds the alarm (press and hold) : This setting must be custom- ized at your Toyota dealer.
  • Page 49 1-3. Opening, closing and locking the doors and trunk ■ Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Trunk: A buzzer sounds to indicate that the trunk has been unlocked. Driver’s window and moon roof: A buzzer sounds to indicate that the driver’s window and moon roof are opening.
  • Page 50 The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details. ■ Customization that can be configured at Toyota dealer Settings (e.g. trunk unlocking function) can be changed. (Customizable features: →P. 498) ■...
  • Page 51 1-3. Opening, closing and locking the doors and trunk Doors The vehicle can be locked and unlocked using the entry function, wireless remote control or door lock switch. ■ Entry function →P. 53 ■ Wireless remote control →P. 66 ■ Door lock switch Locks all the doors Unlocks all the doors...
  • Page 52 1-3. Opening, closing and locking the doors and trunk Locking the doors from the outside without a key STEP Move the inside lock button to the lock position. STEP Close the door. The door cannot be locked if the “POWER” switch is in ACCESSORY or ON mode, or the electronic key is left inside the vehicle.
  • Page 53 1-3. Opening, closing and locking the doors and trunk Automatic door locking and unlocking systems The following functions can be set or cancelled: Function Operation Shift position linked Shifting the shift lever out of P locks all door locking function doors.
  • Page 54 If the smart key system has been deactivated in a customized setting Use the wireless remote control or mechanical key. (→P. 66, 458) ■ Customization that can be configured at Toyota dealer Settings (e.g. unlocking function using a key) can be changed. (Customizable features →P. 498)
  • Page 55 1-3. Opening, closing and locking the doors and trunk CAUTION ■ To prevent an accident Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●...
  • Page 56 1-3. Opening, closing and locking the doors and trunk Trunk The trunk can be opened using the trunk opener, entry function or wireless remote control. ■ Opening the trunk from inside the vehicle Pull up the lever to release the trunk lid.
  • Page 57 1-3. Opening, closing and locking the doors and trunk ■ Trunk light The trunk light turns on when the trunk is opened. ■ Function to prevent the trunk being locked with the electronic key inside ● When all doors are being locked, closing the trunk lid with the electronic key left inside the trunk will sound an alarm.
  • Page 58 1-3. Opening, closing and locking the doors and trunk CAUTION ■ Caution while driving ● Keep the trunk lid closed while driving. If the trunk lid is left open, it may hit near-by objects while driving or lug- gage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard.
  • Page 59 ● Do not attach any accessories other than genuine Toyota parts to the trunk lid. Such additional weight on the trunk lid may cause the lid to fall closed again after it is opened.
  • Page 60 1-4. Adjustable components (seats, mirrors, steering wheel) Front seats Manual seat Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (driver’s side only)
  • Page 61 1-4. Adjustable components (seats, mirrors, steering wheel) Power seat Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch (driver’s side only) Vertical height adjustment switch (driver’s side only) Lumbar support adjustment switch (driver’s side only)
  • Page 62 1-4. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Seat adjustment ● To reduce the risk of sliding under the lap belt during a collision, do not recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident.
  • Page 63 1-4. Adjustable components (seats, mirrors, steering wheel) Rear seats The seatback of the right side rear seat can be folded down. Folding down the rear seatback Pull the seatback lever in the trunk.
  • Page 64 1-4. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ When folding the rear seatback down Observe the following precautions. Failure to do so may result in death or serious injury. ● Do not fold the seatback down while driving. ● Stop the vehicle on level ground, set the parking brake and shift the shift lever to P.
  • Page 65 1-4. Adjustable components (seats, mirrors, steering wheel) Head restraints Head restraints are provided for all seats. Vertical adjustment (front seats) Pull the head restraints up. Down Lock release Push the head restraint down button while pushing the lock release button. ■...
  • Page 66 1-4. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the height of the head restraints (front seats) Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. CAUTION ■...
  • Page 67 1-4. Adjustable components (seats, mirrors, steering wheel) Seat belts Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, does come into contact with the...
  • Page 68 1-4. Adjustable components (seats, mirrors, steering wheel) ■ Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.
  • Page 69 1-4. Adjustable components (seats, mirrors, steering wheel) ■ Emergency locking retractor (ELR) The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
  • Page 70 Toyota dealer free of charge. ■ Rear seat belt Use the seat belt after passing it through the guide if the seat belt comes free from...
  • Page 71 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system. ●...
  • Page 72 ● Ensure that the belt and plate are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
  • Page 73 1-4. Adjustable components (seats, mirrors, steering wheel) CAUTION ■ Using a seat belt extender ● Do not wear the seat belt extender if you can fasten the seat belt without the extender. ● Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.
  • Page 74 1-4. Adjustable components (seats, mirrors, steering wheel) Steering wheel The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and STEP push the lever down. Adjust to the ideal position by STEP moving the steering wheel horizontally and vertically.
  • Page 75 1-4. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror Glare from the headlights of vehicles behind can be reduced by using the following functions: Manual anti-glare inside rear view mirror Normal position Anti-glare position Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
  • Page 76 1-4. Adjustable components (seats, mirrors, steering wheel) Adjusting the height of rear view mirror Adjust the height of the rear view mirror by moving it up and down. ■ To prevent sensor error (vehicles with auto anti-glare inside rear view mirror) To ensure that the sensors operate prop- erly, do not touch or cover them.
  • Page 77 1-4. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors Mirror angle can be adjusted using the switch. To select a mirror to adjust, STEP press the switch. Left Right To adjust the mirror, press the STEP switch. Right Down Left Folding the mirrors...
  • Page 78 1-4. Adjustable components (seats, mirrors, steering wheel) ■ Mirror angle can be adjusted when The “POWER” switch is in ACCESSORY or ON mode. ■ When the mirrors are fogged up (vehicles with mirror defoggers) Turn on the mirror defoggers to defog the mirrors. (→P. 239) CAUTION ■...
  • Page 79 1-5. Opening and closing the windows and moon roof Power windows The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows: Closing One-touch closing (driver’s window only) Opening One-touch opening (driver’s window only) Pressing the switch in the opposite direction will stop win-...
  • Page 80 If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
  • Page 81 1-5. Opening and closing the windows and moon roof ■ Customization that can be configured at Toyota dealer Settings (e.g. key linked operation) can be changed. (Customizable features: →P. 498) CAUTION ■ Closing the windows Observe the following precautions. Failure to do so may result in death or serious injury.
  • Page 82 1-5. Opening and closing the windows and moon roof ∗ Moon roof Use the overhead switches to open and close the moon roof and tilt it up and down. ■ Opening and closing Opens the moon roof* The moon roof stops slightly before the fully open position to reduce wind noise.
  • Page 83 1-5. Opening and closing the windows and moon roof ■ The moon roof can be operated when The “POWER” switch is in ON mode. ■ Operating the moon roof after turning the engine off The moon roof can be operated for approximately 45 seconds even after the “POWER”...
  • Page 84 Check to make sure that the moon roof is completely closed and then release the switch. If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.
  • Page 85 “POWER” switch is turned off and the driver's door is opened with the moon roof open. ■ Customization that can be configured at Toyota dealer Settings (e.g. key linked operation) can be changed. (Customizable features: →P. 498) CAUTION ■...
  • Page 86 1-6. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle Turn the “POWER” switch off and close all the doors and win- dows. ■ Opening the fuel tank cap Pull up the opener to open the STEP fuel filler door.
  • Page 87 1-6. Refueling Closing the fuel tank cap After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.
  • Page 88 ■ When replacing the fuel cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
  • Page 89 1-6. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.
  • Page 90 1-7. Theft deterrent system Immobilizer system The vehicle's keys have built-in transponder chips that prevent the hybrid system from starting if a key has not been previously regis- tered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle. The indicator light flashes after the “POWER”...
  • Page 91 1-7. Theft deterrent system CAUTION ■ Certifications for the immobilizer system Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTICE ■ To ensure the system operates correctly Do not modify or remove the system.
  • Page 92 1-7. Theft deterrent system ∗ Alarm The system sounds the alarm and flashes the lights when forced entry is detected. ■ Triggering of the alarm The alarm is triggered in the following situations when the alarm is set: ● A locked door or trunk is unlocked or opened in any way other than using the entry function, wireless remote control or mechanical key.
  • Page 93 1-7. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: ● Nobody is in the vehicle. ●...
  • Page 94 1-7. Theft deterrent system NOTICE ■ To ensure the system operates correctly Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
  • Page 95 1-8. Safety information Correct driving posture Drive in a good posture as follows: Sit upright and well back in the seat. (→P. 78) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily depressed to the extent required.
  • Page 96 1-8. Safety information CAUTION ■ While driving ● Do not adjust the position of the driver’s seat. Doing so could cause the driver to lose control of the vehicle. ● Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
  • Page 97 1-8. Safety information SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. SRS front airbags SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas-...
  • Page 98 1-8. Safety information SRS curtain shield airbags Can help protect primarily the head of occupants in the outer seats SRS airbag system components Front impact sensors “AIR BAG ON” and “AIR BAG OFF” indicator lights Front passenger occupant classification system (ECU SRS warning light and sensors) Front passenger’s seat belt...
  • Page 99 1-8. Safety information Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above.
  • Page 100 1-8. Safety information ■ If the SRS airbags deploy (inflate) ● Bruising and slight abrasions may result from contact with a deploying (inflating) SRS airbag. ● A loud noise and white powder will be emitted. ● Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the seats, parts of the front and rear pillars, and roof side rails, may be hot for several minutes.
  • Page 101 1-8. Safety information ■ SRS airbag deployment conditions (SRS side and curtain shield air- bags) ● The SRS side and curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corre- sponding to the impact force produced by an approximately 3300 lb.
  • Page 102 1-8. Safety information ■ Types of collisions that may not deploy the SRS airbags (SRS front air- bags) The SRS front airbags do not generally inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low-speed frontal collision.
  • Page 103 1-8. Safety information ■ Types of collisions that may not deploy the SRS airbags (SRS side and curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.
  • Page 104 1-8. Safety information ■ When to contact your Toyota dealer In the following cases, contact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ● The front of the vehicle is damaged or...
  • Page 105 1-8. Safety information CAUTION ■ SRS airbag precautions Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly.
  • Page 106 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are safer for infants and children than the front passenger seat.
  • Page 107 1-8. Safety information CAUTION ■ SRS airbag precautions ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger. ● Do not allow the front seat occupants to hold items on their knees.
  • Page 108 1-8. Safety information CAUTION ■ SRS airbag precautions ● Do not attach anything to areas such as a door, windshield glass, side door glass, front or rear pillar, roof side rail and assist grip. ● Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and may cause death or serious injury, should the SRS curtain shield airbags deploy.
  • Page 109 Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
  • Page 110 1-8. Safety information Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.
  • Page 111 1-8. Safety information Condition and operation in the front passenger occupant classification system ■ Adult “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights ON” Indicator/ SRS warning light warning light Seat belt reminder light Flashing Front passenger airbag Side airbag on the front passenger seat Devices...
  • Page 112 1-8. Safety information ■ Unoccupied “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights OFF” Indicator/ warning light SRS warning light Seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seat Activated Devices Curtain shield airbag in the front passenger side Front passenger knee airbag...
  • Page 113 1-8. Safety information : Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 133) : In case the indicator light is not illuminated, consult this manual on how to install the child restraint system properly.
  • Page 114 Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
  • Page 115 1-8. Safety information Child restraint systems A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
  • Page 116 1-8. Safety information Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child: Rear facing ⎯ Infant seat/convertible seat Forward facing ⎯ Convertible seat Booster seat...
  • Page 117 ● Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
  • Page 118 1-8. Safety information CAUTION ■ Child restraint precautions ● Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or accident.
  • Page 119 1-8. Safety information Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.
  • Page 120 1-8. Safety information Installation with LATCH system Type A STEP Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower STEP straps onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.
  • Page 121 1-8. Safety information Type B STEP Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the STEP LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.
  • Page 122 1-8. Safety information Installing child restraints using a seat belt (child restraint lock function belt) Rear facing ⎯ Infant seat/convertible seat ■ Place the child restraint system STEP on the rear seat facing the rear of the vehicle. Run the seat belt through the STEP child restraint system and insert the plate into the buckle.
  • Page 123 1-8. Safety information While pushing the child restraint STEP system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
  • Page 124 1-8. Safety information While pushing the child restraint STEP system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. After shoulder belt retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
  • Page 125 1-8. Safety information Removing a child restraint installed with a seat belt Push the buckle release button and fully retract the seat belt. Child restraint systems with a top tether strap Secure the child restraint using STEP the seat belt or LATCH anchors. Open the anchor bracket cover, STEP latch the hook onto the anchor...
  • Page 126 1-8. Safety information ■ Laws and regulations pertaining to anchorages The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to SAE J1819. CAUTION ■...
  • Page 127 1-8. Safety information CAUTION ■ When installing a child restraint system Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking, sudden swerving or an accident.
  • Page 128 1-8. Safety information CAUTION ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder.
  • Page 129 2-1. Driving procedures Driving the vehicle The following procedures should be observed to ensure safe driv- ing: ■ Starting the hybrid system →P. 159 ■ Driving STEP With the brake pedal depressed, shift the shift lever to D. (→P. 169) STEP Release the parking brake.
  • Page 130 The vehicle is judged to be driving uphill or downhill ● When the accelerator pedal is released ■ Breaking in your new Toyota To extend the life of the vehicle, observing the following precautions is rec- ommended: ● For the first 200 miles (300 km): Avoid sudden stops.
  • Page 131 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down operation.
  • Page 132 If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately.
  • Page 133 2-1. Driving procedures CAUTION ● Do not shift the shift lever to P while the vehicle is moving. Doing so can damage the transmission and may result in a loss of vehicle control. ● Do not shift the shift lever to R while the vehicle is moving forward. Doing so can damage the transmission and may result in a loss of vehicle control.
  • Page 134 If you hear a squealing or scraping noise (brake pad wear limit indica- tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed.
  • Page 135 2-1. Driving procedures CAUTION ■ When the vehicle is stopped ● Do not depress the accelerator pedal unnecessarily. If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, causing an accident. ●...
  • Page 136 2-1. Driving procedures CAUTION ■ When the vehicle is parked ● Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in the vehicle when it is in the sun. Doing so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may lead to a fire.
  • Page 137 The exhaust system should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.
  • Page 138 If this happens, do not continue to drive the vehicle. If the brake system warning light (red indicator) comes on together with the buzzer sound while driving, immediately stop the vehicle in a safe place and con- tact your Toyota dealer. NOTICE ■...
  • Page 139 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ● Brake function ●...
  • Page 140 2-1. Driving procedures Power (ignition) switch Performing the following operations when carrying the electronic key on your person starts the hybrid system or changes “POWER” switch modes. ■ Starting the hybrid system STEP Check that the parking brake is set. STEP Check that the shift lever is set in P.
  • Page 141 2-1. Driving procedures ■ Stopping the hybrid system STEP Stop the vehicle. STEP Shift the shift lever to P. STEP Set the parking brake. (→P. 172) STEP Release the brake pedal. STEP Press the “POWER” switch. STEP Check that on the multi-information display is off.
  • Page 142 2-1. Driving procedures ■ Changing “POWER” switch modes Modes can be changed by pressing the “POWER” switch with brake pedal released. (The mode changes each time the switch is pressed.) Off* The emergency flashers can be used. The multi-information display will not be displayed.
  • Page 143 2-1. Driving procedures When stopping the hybrid system with the shift lever in a position other than P If the hybrid system is stopped with the shift lever in a position other than P, the “POWER” switch will not be turned off but instead be turned to ACCESSORY mode.
  • Page 144 In this case, refrain from operating the hybrid system. After about 10 seconds, the steering lock motor will resume functioning. ■ When “CHECK SMART KEY SYSTEM” will be displayed on the multi- information display. The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.
  • Page 145 If the “READY” indicator does not come on If the “READY” indicator does not come on when you press the “POWER” switch with the shift lever in P and the brake pedal depressed, contact your Toyota dealer immediately. ■ If the hybrid system is malfunctioning →P.
  • Page 146 Do not depress the accelerator pedal unnecessarily. ■ Symptoms indicating a malfunction with the “POWER” switch If the “POWER” switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction. Con- tact your Toyota dealer immediately.
  • Page 147 2-1. Driving procedures EV drive mode In EV drive mode the electric motor (traction motor), powered by the hybrid battery (traction battery), is used to drive the vehicle. This mode allows you to drive in residential areas early in the morn- ing and late at night, or in indoor parking lots etc.
  • Page 148 2-1. Driving procedures ■ Switching to EV drive mode when the gasoline engine is cold If the hybrid system is started while the gasoline engine is cold, the gasoline engine will start automatically after a short period of time in order to warm up.
  • Page 149 ■ Fuel economy Your Toyota is designed to achieve the best possible fuel economy during normal driving (using the gasoline engine and electric motor [traction motor]). Driving in EV drive mode more than necessary may lower fuel econ- omy.
  • Page 150 2-1. Driving procedures Hybrid transmission Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever While the “POWER” switch is in ON mode, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.
  • Page 151 2-1. Driving procedures ■ Selecting Eco drive mode When the vehicle is driven in Eco drive mode, vehicle driving force and operation of the air conditioning system (heating/cool- ing) is controlled to improve fuel efficiency. Eco drive mode When eco drive mode is turned on, the “ECO MODE”...
  • Page 152 2-1. Driving procedures Turn signal lever The turn signal lever can be used to show the following intentions of the driver: Right turn Left turn Lane change to the right (push and hold the lever partway) The right hand signals will flash until you release the lever.
  • Page 153 2-1. Driving procedures Parking brake To set the parking brake, fully depress the parking brake pedal with your left foot while U.S.A. Canada depressing the brake pedal with your right foot. (Depressing the pedal again releases the parking brake.) ■ Usage in winter time See “Winter driving tips”...
  • Page 154 2-1. Driving procedures Horn To sound the horn, press on or close to the mark. ■ After adjusting the steering wheel Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P.
  • Page 155 2-2. Instrument cluster Gauges and meters Hybrid System Indicator Displays hybrid system power output and regenerative level Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Average fuel consumption meter Displays the average fuel consumption since the function was reset. Current fuel consumption gauge Displays the current rate of fuel consumption.
  • Page 156 2-2. Instrument cluster Engine coolant temperature display/instrument panel light con- trol display Displays the engine coolant temperature and instrument panel light control. Outside temperature display →P. 301 Shift position display Displays the currently selected shift position. →P. 169 Instrument panel light control button →P.
  • Page 157 2-2. Instrument cluster Changing the odometer/trip meter display Pressing the button changes the display as follows. ● Odometer Displays the total distance the vehicle has been driven. ● Trip meters A and B Displays the distance the vehicle has been driven since the meter was last reset.
  • Page 158 2-2. Instrument cluster Instrument panel light control button The brightness of the instrument panel lights can be adjusted. Pressing the button will adjust brightness of the instrument panel lights.
  • Page 159 2-2. Instrument cluster ■ The meters and display illuminate when The “POWER” switch is in ON mode. ■ Hybrid System Indicator Power area Shows that an Eco-friendly driving range is being exceeded (during full power driving etc.) Eco area Shows that the vehicle is being driven in an Eco-friendly manner.
  • Page 160 2-2. Instrument cluster ■ The brightness of the instrument panel lights When the tail lights are turned on, the meter’s brightness will be reduced slightly unless the meter brightness level adjustment is set to the brightest setting. If the tail lights are turned on when the surroundings are dark, the meter’s brightness will reduce slightly.
  • Page 161 2-2. Instrument cluster Indicators and warning lights The indicator and warning lights on the instrument cluster, center panel and outside rear view mirrors inform the driver of the status of the vehicle’s various systems. ■ Instrument cluster ■ Center panel...
  • Page 162 2-2. Instrument cluster ■ Outside rear view mirrors (if equipped)
  • Page 163 2-2. Instrument cluster ■ Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. BSM outside rear view Turn signal indicator mirror indicators (→P. 171) (→P. 215) (if equipped) Headlight high beam Headlight indicator indicator (→P. 194) (→P.
  • Page 164 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
  • Page 165 There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.
  • Page 166 2-2. Instrument cluster Multi-information display The multi-information display presents the driver with a variety of driving-related data. ● Trip information (→P. 187) Displays cruising range, fuel consumption and other cruis- ing-related information. ● Warning messages (→P. 423) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.
  • Page 167 2-2. Instrument cluster ■ Display contents Trip information contents Switching display items Cruising range/average fuel consumption Average vehicle speed/ elapsed time Press the “DISP” button. Eco drive level Energy monitor Customization - (off)
  • Page 168 2-2. Instrument cluster Trip information ■ Cruising range/average fuel consumption Cruising range Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.
  • Page 169 2-2. Instrument cluster ■ Eco drive level Displays the average fuel consumption and eco drive level since the hybrid system was started. Even if a different screen has been selected for the multi-information dis- play, when the “POWER” switch is turned off, the eco drive level is dis- played.
  • Page 170 2-2. Instrument cluster Press the “DISP” button to select STEP the item to be set, then press and hold the “DISP” button. Press the “DISP” button to select STEP the desired setting, and then press and hold the “DISP” but- ton.
  • Page 171 2-2. Instrument cluster Press the “DISP” button to select STEP the item to be set, then press and hold the “DISP” button. Press the “DISP” button to select STEP the desired setting, and then press and hold the “DISP” but- ton.
  • Page 172 2-2. Instrument cluster Press the “DISP” button to select STEP the item to be set, then press and hold the “DISP” button. Press the “DISP” button to select STEP the desired setting, and then press and hold the “DISP” but- ton.
  • Page 173 2-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: U.S.A. The headlights, parking lights, daytime running lights and so on turn on and off automatically (when the “POWER”...
  • Page 174 2-3. Operating the lights and wipers Canada The headlights, park- ing lights, daytime run- ning lights and so on turn on and off auto- matically (when “POWER” switch is in ON mode). The side marker, park- ing, tail, license plate, daytime running lights and instrument panel lights turn on.
  • Page 175 2-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off.
  • Page 176 2-3. Operating the lights and wipers ■ Guide to dial settings Occupancy and luggage load conditions Dial position Occupants Luggage load Driver None Driver and front pas- None senger All seats occupied None All seats occupied Full luggage loading Driver Full luggage loading ■...
  • Page 177 20 minutes after the 12-volt battery-saving function has been reactivated: ● When the headlight switch is operated ● When a door is opened or closed ■ Customization that can be configured at Toyota dealer Settings (e.g. Light sensor sensitivity) can be changed. (Customizable features →P. 498)
  • Page 178 2-3. Operating the lights and wipers NOTICE ■ To prevent 12-volt battery discharge Do not leave the lights on longer than necessary when the hybrid system is off.
  • Page 179 2-3. Operating the lights and wipers ∗ Fog light switch The fog lights secure excellent visibility in difficult driving condi- tions, such as in rain and fog. U.S.A. Turns the front fog lights off Turns the front fog lights on ∗...
  • Page 180 2-3. Operating the lights and wipers Canada Turns the front fog lights off Turns the front fog lights on ■ Fog lights can be used when The headlights are on in low beam.
  • Page 181 2-3. Operating the lights and wipers Windshield wipers and washer When is selected, the wiper interval can be adjusted for intermittent operation. The wiper operation is selected by moving the lever as follows. U.S.A. Intermittent windshield wiper operation Low speed windshield wiper operation High speed...
  • Page 182 2-3. Operating the lights and wipers Washer/wiper dual opera- tion The wipers will automatically operate a couple of times after the washer squirts. Canada When is selected, the wiper interval can be adjusted for inter- mittent operation. The wiper operation is selected by moving the lever as follows. Intermittent windshield wiper operation...
  • Page 183 2-3. Operating the lights and wipers Increases the intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency Washer/wiper dual opera- tion The wipers will automatically operate a couple of times after the washer squirts. ■ The windshield wipers and washer can be operated when The “POWER”...
  • Page 184 Do not operate the switch continually as the washer fluid pump may over- heat. ■ When a nozzle becomes blocked In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.
  • Page 185 2-4. Using other driving systems Cruise control Use the cruise control to maintain a set speed without depressing the accelerator pedal. Indicators Cruise control switch ■ Setting the vehicle speed Press the “ON-OFF” button to STEP activate the cruise control. Cruise control indicator will come on.
  • Page 186 2-4. Using other driving systems ■ Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction.
  • Page 187 2-4. Using other driving systems ■ Cruise control can be set when ● The shift lever is in D. ● Vehicle speed is above approximately 25 mph (40 km/h). ■ Accelerating after setting the vehicle speed ● The vehicle can be accelerated normally. After acceleration, the set speed resumes.
  • Page 188 2-4. Using other driving systems Driving assist systems To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■...
  • Page 189 2-4. Using other driving systems When the TRAC/VSC/ABS systems are operating The slip indicator flashes to indi- cate that the ABS/VSC/TRAC systems are operating.
  • Page 190 2-4. Using other driving systems Disabling the TRAC/VSC systems If the vehicle gets stuck in fresh snow or mud, the TRAC/VSC sys- tems may reduce power from the hybrid system to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it.
  • Page 191 ■ When the “TRAC OFF” indicator light comes on even if the VSC OFF switch has not been pressed TRAC cannot be operated. Contact your Toyota dealer. ■ Sounds and vibrations caused by the ABS, brake assist, VSC and TRAC ●...
  • Page 192 The EPS system should return to normal within 10 minutes. ■ If the slip indicator comes on... It may indicate a malfunction in the TRAC, VSC and ABS. Contact your Toyota dealer. CAUTION ■ ABS does not operate effectively when ●...
  • Page 193 The ABS, TRAC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a system to malfunction.
  • Page 194 2-4. Using other driving systems Hill-start assist control Hill-start assist control helps to prevent the vehicle from rolling backwards when starting on an incline or slippery slope. To engage hill-start assist con- trol, further depress the brake pedal when the vehicle is stopped completely.
  • Page 195 • The brake pedal is depressed again. • The brake pedal has been depressed for more than approximately 3 minutes. ■ If the slip indicator comes on It may indicate a malfunction in the system. Contact your Toyota dealer. CAUTION ■ Hill-start assist control ●...
  • Page 196 2-4. Using other driving systems ∗ BSM (Blind Spot Monitor) The Blind Spot Monitor is a system that assists the driver to confirm safety when changing lanes. The system uses radar sensors to detect vehicles that are traveling in an adjacent lane in the area that is not reflected in the outside rear view mirror (the blind spot), and advises the driver of the vehicles existence via the outside rear view mirror indicator.
  • Page 197 2-4. Using other driving systems The Blind Spot Monitor detection areas The blind spot that vehicles can be detected in are outlined below. The range of the detection area extends to: Approximately 11.5 ft. (3.5 m) from the side of the vehicle The first 1.6 ft.
  • Page 198 2-4. Using other driving systems ■ Conditions under which the Blind Spot Monitor will not detect a vehicle The Blind Spot Monitor is not designed to detect the following types of vehi- cles and/or objects: ● Small motorcycles, bicycles, pedestrians etc.* ●...
  • Page 199 2-4. Using other driving systems ● Instances of the Blind Spot Monitor unnecessarily detecting a vehicle and/or object may increase under the following conditions: • When there is only a short distance between your vehicle and a guard- rail, wall etc. •...
  • Page 200 If the sensor moves even slightly off position, the system may mal- function and vehicles that enter the detection area may not be detected. If the sensor or surrounding area is subject to a strong impact, always have the area inspected by your Toyota dealer. ● Do not disassemble the sensor.
  • Page 201 2-5. Driving information Cargo and luggage Take notice of the following information about storage precau- tions, cargo capacity and load: ● Stow cargo and luggage in the trunk whenever possible. ● Be sure all items are secured in place. ● To maintain vehicle balance while driving, position luggage evenly within the luggage compartment.
  • Page 202 Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 472) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing. Example based on your vehicle Cargo capacity Total load capacity When 2 people with the combined weight of 366 lb.
  • Page 203 2-5. Driving information CAUTION ■ Things that must not be carried in the trunk The following things may cause a fire if loaded in the trunk: ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions. Failure to do so may result in death or serious injury.
  • Page 204 2-5. Driving information CAUTION ■ Capacity and distribution ● Do not exceed the maximum axle weight rating or the total vehicle weight rating. ● Even if the total load of occupant's weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.
  • Page 205 Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. ■ Towing capacity Toyota does not recommend towing a trailer with your vehicle. ■ Cargo capacity Cargo capacity may increase or decrease depending on the weight and the number of occupants.
  • Page 206 2-5. Driving information Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations ● Use fluids that are appropriate to the prevailing outside tem- peratures.
  • Page 207 2-5. Driving information ■ When driving the vehicle Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions. ■ When parking the vehicle Park the vehicle and move the shift lever to P without setting the parking brake.
  • Page 208 2-5. Driving information ■ Tire chain installation Observe the following precautions when installing and removing chains: ● Install and remove tire chains in a safe location. ● Install tire chains on the front tires only. Do not install tire chains on the rear tires.
  • Page 209 NOTICE ■ Repairing or replacing snow tires Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
  • Page 210 Trailer towing Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your vehicle is not designed for trailer towing or for the use of tow...
  • Page 211 2-5. Driving information Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with the four wheels on the ground.
  • Page 212 3-1. Using the air conditioning system and defogger Automatic air conditioning system Air outlets and fan speed are automatically adjusted according to the temperature setting. Driver’s side temperature Air outlet display setting display Front passenger’s side Fan speed temperature setting display Driver’s side display temperature control...
  • Page 213 3-1. Using the air conditioning system and defogger Using the automatic air conditioning system STEP Press The air conditioning system begins to operate. Air outlets and fan speed are automatically adjusted according to the temper- ature setting. STEP Turn clockwise to increase the temperature and turn counterclockwise to decrease the temperature.
  • Page 214 3-1. Using the air conditioning system and defogger Defogging the windshield Press dehumidification function operates speed increases. Set the outside/recirculated air mode button to the outside air mode if the recirculated air mode is used. (It may switch automati- cally.) To defog the windshield and the side windows early, turn the air flow and temperature up.
  • Page 215 3-1. Using the air conditioning system and defogger Air flows to the upper body and feet. : AVV50L-CEXGBA models only Air flows to the feet. : When the warming function is operating, air flows to the upper body as well to warm the upper body effectively.
  • Page 216 3-1. Using the air conditioning system and defogger Adjusting the position of and opening and closing the air outlets Front center outlets Direct air flow to the left or right, up or down. Front side outlets Direct air flow to the left or right, up or down.
  • Page 217 3-1. Using the air conditioning system and defogger ■ Operation of the air conditioning system in Eco drive mode In Eco drive mode, the air conditioning system is controlled as follows to pri- oritize fuel efficiency: ● Engine speed and compressor operation controlled to restrict heating/ cooling capacity ●...
  • Page 218 ■ Air conditioning filter →P. 380 ■ Customization that can be configured at Toyota dealer Settings (e.g. air conditioning setting) can be changed. (Customizable features →P. 498) CAUTION ■ To prevent the windshield from fogging up Do not use during cool air operation in extremely humid weather.
  • Page 219 3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers Defoggers are used to defog the rear window, and to remove rain- drops, dew and frost from the outside rear view mirrors. Turns the defoggers on/off The defoggers will automati- cally turn off the operation time.
  • Page 220: Table Of Contents

    3-2. Using the audio system Audio system types Without navigation system and Display Audio system CD player and AM/FM radio Title Page Using the radio P. 246 Using the CD player P. 249 Playing back MP3 and WMA discs P. 255 Operating an iPod P.
  • Page 221 3-2. Using the audio system With Display Audio system Owners of models equipped with a Display Audio system should refer to the “Display Audio System Owner's Manual”. Display Audio system Premium Display Audio system With navigation system Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”.
  • Page 222 3-2. Using the audio system ® ■ About Bluetooth (with Display Audio system) The Bluetooth wordmark and logo are owned by Bluetooth SIG. and permis- sion has been granted to use the trademark of the licensee Panasonic Cor- poration/Pioneer Corporation. Other trademarks and trade names are owned by various different owners.
  • Page 223 3-2. Using the audio system CAUTION • This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio fre- quency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equip- ment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE).
  • Page 224 3-2. Using the audio system CAUTION ● Laser products • Do not take this unit apart or attempt to make any changes yourself. This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet.
  • Page 225 3-2. Using the audio system NOTICE ■ To prevent 12-volt battery discharge Do not leave the audio system on longer than necessary when the hybrid system is off. ■ To avoid damaging the audio system Take care not to spill drinks or other fluids over the audio system.
  • Page 226: Using The Radio

    3-2. Using the audio system Using the radio Power Volume Preset station selector Adjusting the frequency Displaying radio text messages Seeking the AM/FM mode button Scanning for frequency receivable stations Setting station presets STEP Search for a desired station by turning or pressing STEP Press and hold a button (from...
  • Page 227 3-2. Using the audio system Scanning radio stations ■ Scanning the preset radio stations STEP Press and hold until you hear a beep. Preset stations will be played for 5 seconds each. STEP When the desired station is reached, press once again.
  • Page 228 3-2. Using the audio system ■ Reception sensitivity ● Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc. ●...
  • Page 229: Using The Cd Player

    3-2. Using the audio system Using the CD player Selecting a track/ Power Volume displaying track list Repeat play Random Playback/pause playback Back button CD eject Displaying text messages Searching playback Selecting a track, fast-forwarding or reversing Loading CDs Insert a CD. Ejecting CDs Press and remove the CD.
  • Page 230 3-2. Using the audio system Selecting a track from a track list STEP Press The track list will be displayed. STEP Turn and press to select a track. To return to the previous display, press Scanning tracks STEP Press The first 10 seconds of each track will be played. To cancel, press again.
  • Page 231 3-2. Using the audio system Random playback Press (RDM). Tracks are played in a random order until (RDM) is pressed again. Playing and pausing tracks Press Switching the display Press Each time is pressed, the display changes in the following order: Track no./Elapsed time →...
  • Page 232 “CD CHECK”: The CD may be dirty, damaged or inserted up-side down. “WAIT”: Operation has stopped due to a high temperature inside the player. Contact your Toyota dealer if the CD still cannot be played. ■ Discs that can be used Discs with the marks shown below can be used.
  • Page 233 3-2. Using the audio system NOTICE ■ CDs and adapters that cannot be used Do not use the following types of CDs or 3 in. (8 cm) CD adapters or Dual Disc. Doing so may damage the CD player and/or the CD insert/eject function. ●...
  • Page 234 3-2. Using the audio system NOTICE ■ CD player precautions Failure to follow the precautions below may result in serious damage to the CDs or the player itself. ● Do not insert anything other than CDs into the CD slot. ●...
  • Page 235: Playing Back Mp3 And Wma Discs

    3-2. Using the audio system Playing back MP3 and WMA discs Power Volume Selecting a file/ Repeat play displaying folder lists Random Playback/pause playback Back button CD eject Displaying Searching text playback messages Selecting a folder Selecting a file, fast-forwarding or reversing Loading and ejecting MP3 and WMA discs →P.
  • Page 236 3-2. Using the audio system ■ Scanning the first file of all the folders STEP Press and hold until you hear a beep. The first 10 seconds of the first file in each folder will be played. STEP When the desired folder is reached, press again.
  • Page 237 3-2. Using the audio system Fast-forwarding and reversing files Press and hold Repeat play Pressing (RPT) changes modes in the following order: File repeat → Folder repeat* → Off. *: Available except when RDM (random playback) is selected Random playback Pressing (RDM) changes modes in the following order: Folder random →...
  • Page 238 The CD may be dirty, damaged or inserted up-side down. “WAIT”: Operation has stopped due to a high temperature inside the player. Contact your Toyota dealer if the CD still cannot be played. “NO SUPPORT”: This indicates that MP3/WMA files are not included in the ■...
  • Page 239 3-2. Using the audio system ■ Lens cleaners Do not use lens cleaners. Doing so may damage the CD player. ■ MP3 and WMA files MP3 (MPEG Audio LAYER3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size by using MP3 compression.
  • Page 240 3-2. Using the audio system ● Compatible media Media that can be used for MP3 and WMA playback are CD-Rs and CD- RWs. Playback in some instances may not be possible, depending on the status of the CD-R or CD-RW. Playback may not be possible or the audio may jump if the disc is scratched or marked with fingerprints.
  • Page 241 3-2. Using the audio system ● MP3 and WMA playback When a disc containing MP3 or WMA files is inserted, all files on the disc are first checked. Once the file check is finished, the first MP3 or WMA file is played.
  • Page 242: Operating An Ipod

    3-2. Using the audio system Operating an iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. ■ Connecting an iPod Push the lid. STEP Open the cover and connect STEP an iPod using an iPod cable. Turn on the power of the iPod if it is not turned on.
  • Page 243 3-2. Using the audio system ■ Control panel Power Volume iPod menu mode/back button Shuffle playback iPod menu/selecting a song/displaying lists Playback/pause Repeat play Displaying text messages Play button Selecting a song, fast-forwarding or reversing Selecting a play mode STEP Press (BROWSE) to select iPod menu mode.
  • Page 244 3-2. Using the audio system ■ Play mode list First Second Third Fourth Play mode selection selection selection selection Playlists Songs “Playlists” select select Albums Songs “Artists” Artists select select select Albums Songs “Albums” select select “Songs” Songs select Podcasts Episodes “Podcasts”...
  • Page 245 3-2. Using the audio system Selecting songs Turn or press to select the desired song. Selecting a song from the song list STEP Press The song list will be displayed. STEP Turn to select a song. STEP Press to play the song. To return to the previous display, press Fast-forwarding and reversing songs Press and hold...
  • Page 246 3-2. Using the audio system Shuffle playback Pressing (RDM) changes modes in the following order: Track shuffle → Album shuffle → Off. Playing and pausing songs Press Switching the display Press Each time is pressed, the display changes in the following order: Track no./Elapsed time →...
  • Page 247 3-2. Using the audio system ● Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance. ●...
  • Page 248 3-2. Using the audio system ■ Error messages “ERROR 1”: This indicates that the data in the iPod cannot be read. “ERROR 3”: This indicates that the iPod may be malfunctioning. “ERROR 4”: This indicates that an over current error has occurred. “ERROR 5”: This indicates that an iPod communication error has occurred.
  • Page 249 3-2. Using the audio system Depending on differences between models or software versions etc., some models might be incompatible with this system. Items related to standards and limitations are as follows: ● Maximum number of lists in device: 9999 ● Maximum number of songs in device: 65535 ●...
  • Page 250: Operating A Usb Memory

    3-2. Using the audio system Operating a USB memory Connecting a USB memory enables you to enjoy music from the vehicle speakers. ■ Connecting a USB memory Push the lid. STEP Open the cover and connect a STEP USB memory. Turn on the power of the USB memory if it is not turned on.
  • Page 251 3-2. Using the audio system ■ Control panel Power Volume Selecting a file/ Random displaying folder lists Playback/pause playback Back button Repeat play Displaying Searching text playback messages Selecting a folder Selecting a file, fast-forwarding or reversing Selecting and scanning a folder ■...
  • Page 252 3-2. Using the audio system ■ Scanning the first file of all the folders STEP Press and hold until you hear a beep. The first 10 seconds of the first file in each folder will be played. STEP When the desired folder is reached, press again.
  • Page 253 3-2. Using the audio system Fast-forwarding and reversing files Press and hold Repeat play Pressing (RPT) changes modes in the following order: File repeat → Folder repeat* → Off. *: Available except when RDM (random playback) is selected Random playback Pressing (RDM) changes modes in the following order: 1 folder random →...
  • Page 254 3-2. Using the audio system ■ USB memory functions ● Depending on the USB memory that is connected to the system, the device itself may not be operable and certain functions may not be avail- able. If the device is inoperable or a function is unavailable due to a mal- function (as opposed to a system specification), disconnecting the device and reconnecting it once again may resolve the problem.
  • Page 255 3-2. Using the audio system ● MP3 and WMA files MP3 (MPEG Audio LAYER 3) is a standard audio compression format. Files can be compressed to approximately 1/10 of their original size using MP3 compression. WMA (Windows Media Audio) is a Microsoft audio compression format. This format compresses audio data to a size smaller than that of the MP3 format.
  • Page 256 3-2. Using the audio system ● ID3 and WMA tags ID3 tags can be added to MP3 files, making it possible to record the track title, artist name, etc. The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3, 2.4 ID3 tags.
  • Page 257 3-2. Using the audio system NOTICE ■ If the auxiliary box lid cannot be fully closed Depending on the size and shape of the USB memory that is connected to the system, the auxiliary box lid may not close fully. In this case, do not forc- ibly close the lid as this may damage the USB memory or the terminal, etc.
  • Page 258: Optimal Use Of The Audio System

    3-2. Using the audio system Optimal use of the audio system Displays the current mode Changes the following set- ting • Sound quality and volume balance (→P. 279) The sound quality and bal- ance setting can be changed to produce the best sound. •...
  • Page 259 3-2. Using the audio system ■ Adjusting sound quality Turning adjusts the level. Sound qual- Mode Turn to the Turn to the Level ity mode displayed left right Bass* “BAS” -5 to 5 High Treble* “TRE” -5 to 5 Front/rear volume “FAD”...
  • Page 260 3-2. Using the audio system ■ Trademark owned by SRS Labs, Inc. ® ® The audio systems utilize SRS FOCUS and SRS TruBass audio enhancement technologies, under license from SRS Labs, Inc., in all modes except AM radio mode. FOCUS, TruBass, SRS and symbol are trademarks of SRS Labs, Inc.
  • Page 261: Using The Aux Port

    3-2. Using the audio system Using the AUX port This port can be used to connect a portable audio device and listen to it through the vehicle’s speakers. Push the lid. STEP Open the cover and connect STEP the portable audio device. STEP Press repeatedly until “AUX”...
  • Page 262 3-2. Using the audio system NOTICE ■ If the auxiliary box lid cannot be fully closed Depending on the size and shape of the portable audio device that is con- nected to the system, the auxiliary box lid may not close fully. In this case, do not forcibly close the lid as this may damage the portable audio device or the terminal, etc.
  • Page 263 3-2. Using the audio system Using the steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. Volume Radio mode: Selects radio stations CD mode: Selects tracks and files (MP3 and WMA) iPod mode: Selects a song memory mode: Selects a file and folder...
  • Page 264 3-2. Using the audio system Adjusting the volume Press “+” on to increase the volume and “-” to decrease the volume. Hold down “+” or “-” on to continue increasing or decreasing the volume. Silencing a sound Press and hold To cancel, press and hold again.
  • Page 265 3-2. Using the audio system Selecting a folder (MP3 and WMA or USB memory) STEP Press to select CD or USB memory mode. STEP Press and hold until you hear a beep. CAUTION ■ To reduce the risk of an accident Exercise care when operating the audio switches on the steering wheel.
  • Page 266 3-3. Using the interior lights Interior lights list Interior/rear personal lights (vehicles with moon roof) (→P. 287, 288) Interior light (vehicles without moon roof) (→P. 287, 288) Interior/front personal lights (vehicles with moon roof) or per- sonal lights (vehicles without moon roof) (→P. 287, 288) Shift lever light (when the tail lights are on) (vehicles with moon roof) “POWER”...
  • Page 267 3-3. Using the interior lights Interior lights Interior lights Vehicles without moon roof Turns the lights on Turns the door position on Turns the lights off Vehicles with moon roof Turns the lights on/off linked to door positions. Turns the lights on/off...
  • Page 268 “POWER” switch is turned off, the lights will go off automatically after 20 minutes. ■ Customization that can be configured at Toyota dealer Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 498)
  • Page 269 3-4. Using the storage features List of storage features Auxiliary boxes Glove box Bottle holders/door pockets Cup holders Console box Coin holder CAUTION ■ Items that should not be left in the storage spaces Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●...
  • Page 270 3-4. Using the storage features Glove box Glove box The glove box can be opened by pressing the lock release button, locked and unlocked using the mechanical key. Open Lock Unlock CAUTION ■ Caution while driving Keep the glove box closed. In the event of sudden braking or sudden swerv- ing, an accident may occur due to an occupant being struck by the open glove box or the items stored inside.
  • Page 271 3-4. Using the storage features Console box Console box Lift the lid while pulling up the lever to release the lock. ■ When using the console box lid as an armrest Slide the console box lid forward as needed. Slide the lid forward while pulling up the lever.
  • Page 272 3-4. Using the storage features Coin holder Coin holder Pull the lid down while pressing down the button. CAUTION ■ Caution while driving Keep the coin holder closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open coin holder or the items stored inside.
  • Page 273 3-4. Using the storage features Bottle holders Bottle holders Front Rear ■ When using the holder as a bottle holder ● When storing a bottle, close the cap. ● The bottle may not be stored depending on its size or shape. CAUTION ■...
  • Page 274 3-4. Using the storage features Bottle holders and cup holders NOTICE ■ Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glasses and paper cups containing liquid. The contents may spill and glasses may break.
  • Page 275 3-4. Using the storage features Cup holders ■ Cup holder insert Cup holder insert can be removed. CAUTION ■ Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking, causing injury.
  • Page 276 3-4. Using the storage features Auxiliary boxes Auxiliary boxes Type A Push the lid. Type B Push the lid. Type C (if equipped) Lift the lid.
  • Page 277 3-4. Using the storage features Auxiliary boxes CAUTION ■ Caution while driving Keep the auxiliary boxes closed. In the event of sudden braking, an accident may occur due to an occupant being struck by an open auxiliary box or the items stored inside.
  • Page 278 3-5. Other interior features Sun visors To set the visor in the for- ward position, flip it down. To set the visor in the side position, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it back- ward.
  • Page 279 3-5. Other interior features Vanity mirrors Slide the cover to open. Vehicles with vanity lights: The light turns on when the cover is opened. ■ To prevent 12-volt battery discharge (vehicles with vanity lights) If the vanity lights remain on for 20 minutes while the hybrid system is off, the lights will turn off automatically.
  • Page 280 3-5. Other interior features Clock Adjusts the hours Adjusts the minutes ■ The clock is displayed when The “POWER” switch is in ACCESSORY or ON mode. ■ When the 12-volt battery is disconnected The time display will automatically be set to 1:00.
  • Page 281 When the vehicle is stopped, or moving at low speeds (less than 16 mph [25 km/h]) ● When the outside temperature has changed suddenly (at the entrance/ exit of a garage, tunnel, etc.) ■ When “E” is displayed The system may be malfunctioning. Take your vehicle to your Toyota dealer.
  • Page 282 3-5. Other interior features ∗ Ashtray An ashtray can be installed in the cup holder. (→P. 294) CAUTION ■ When not in use Keep the ashtray closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open ashtray or ash flying out. ■...
  • Page 283 3-5. Other interior features Power outlets The power outlet can be used for 12 V accessories that run on less than 10 A. Instrument cluster...
  • Page 284 3-5. Other interior features Center console (if equipped) ■ The power outlet can be used when The “POWER” switch is in ACCESSORY or ON mode. NOTICE ■ To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.
  • Page 285 3-5. Other interior features ∗ Seat heaters The indicator light comes on. Adjusts the seat tempera- ture The further you move the dial forward, the warmer the seat becomes. Front Driver’s seat passenger’s seat ■ The seat heaters can be used when The “POWER”...
  • Page 286 3-5. Other interior features CAUTION ■ Burns ● Use caution when seating the following persons in a seat with the seat heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically chal- lenged •...
  • Page 287 3-5. Other interior features Armrest Fold down the armrest for use. NOTICE ■ To prevent damage to the armrest Do not apply too much load on the armrest.
  • Page 288 3-5. Other interior features Coat hooks CAUTION ■ Items that cannot be hung on the coat hook Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury.
  • Page 289 3-5. Other interior features Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks STEP (clips) into the floor mat eye- lets.
  • Page 290 When installing the driver's floor mat ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver's seat. ●...
  • Page 291 3-5. Other interior features Trunk features ■ Grocery bag hooks...
  • Page 292 3-5. Other interior features ■ Cargo net (if equipped) NOTICE ■ To prevent damage to the hooks Do not apply too much load to the hooks.
  • Page 293 3-5. Other interior features ∗ Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices. ® The garage door opener (HomeLink Universal Transceiver) is manufac- ®...
  • Page 294 3-5. Other interior features ® ■ Programming the HomeLink Point the remote control trans- STEP mitter for the device 1 to 3 in. (25 ® to 75 mm) from the HomeLink control buttons. ® Keep the HomeLink indicator light in view while programming. Press and hold one of the STEP ®...
  • Page 295 3-5. Other interior features ® Test the HomeLink operation STEP by pressing the newly pro- grammed button. ® If a HomeLink button has been programmed for a garage door, check to see if the garage door opens and closes. If the garage door does not operate, see if your remote control transmitter is of the rolling code type.
  • Page 296 HomeLink buttons. ■ Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your Toyota dealer for assistance. ■ Reprogramming a button ® The individual HomeLink buttons cannot be erased but can be reprogrammed.
  • Page 297 3-5. Other interior features ® Operating HomeLink ® ® Press the appropriate HomeLink button. The HomeLink indicator light should come on. ® The HomeLink compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed. ®...
  • Page 298 3-5. Other interior features ■ Before programming ● Install a new battery in the remote control transmitter. ● The battery side of the remote control transmitter must be pointed away ® from the HomeLink button. ■ To prevent 12-volt battery discharge ®...
  • Page 299 3-5. Other interior features CAUTION ■ When programming a garage door or other remote control devices The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm. ■ Conforming to federal safety standards ®...
  • Page 300 3-5. Other interior features ∗ Compass The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation To turn the compass on or off, press “AUTO” for more than 3 seconds. ■ Displays and directions Display Direction...
  • Page 301 3-5. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies depending on the geographic position of the vehicle. If you cross over one of the map boundaries shown in illustration, the compass will deviate.
  • Page 302 3-5. Other interior features STEP Referring to the map above, press “AUTO” to select the num- ber of the zone you are in. If the direction is displayed several seconds after adjustment, the calibration is complete. ■ Circling calibration When “C” appears on the dis- play, drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed.
  • Page 303 3-5. Other interior features CAUTION ■ While driving the vehicle Do not adjust the display. Adjust the display only when the vehicle is stopped. ■ When doing the circling calibration Secure a wide space, and watch out for people and vehicles in the vicinity. Do not violate any local traffic rules while performing circling calibration.
  • Page 304 Telematics Subscription Service Agreement and its Terms and Conditions, as in effect and amended from time to time, a current copy of which is available at Toyota.com. All use of the Safety Con- nect service is subject to such then-applicable Terms and Condi- tions.
  • Page 305 After you have signed the Telematics Subscription Service Agreement and are enrolled, you can begin receiving services. A variety of subscription terms is available for purchase. Contact your Toyota dealer, call 1-800-331-4331, or push the “SOS” but- ton in your vehicle for further subscription details.
  • Page 306 Safety Connect. ● Safety Connect is available beginning Fall 2009 on select Toyota models. Contact with the Safety Connect response center is dependent upon the telematics device being in operative condition, cellular connection avail- ability, and GPS satellite signal reception, which can limit the ability to reach the response center or receive emergency service support.
  • Page 307 ● Green indicator light flashing = Safety Connect call in process ● Red indicator light (except at vehicle start-up) = System malfunc- tion (contact your Toyota dealer) ● No indicator light (off) = Safety Connect service not active Safety Connect services ■...
  • Page 308 In addition to assisting law enforcement with recovery of a stolen vehicle, Safety-Connect-equipped vehicle location data may, under certain circumstances, be shared with third parties to locate your vehicle. Further information is available at Toyota.com. ■ Emergency Assistance Button (“SOS”) In the event of an emergency on the road, push the “SOS”...
  • Page 309 3-5. Other interior features Safety information for Safety Connect Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals.
  • Page 310 3-5. Other interior features ■ Certification for Safety Connect FCC ID: O9EGTM1 FCC ID: O6Y-CDMRF101 NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 311 4-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition: ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
  • Page 312 ■ Precaution regarding the Blind Spot Monitor If the paint of the rear bumper is chipped or scratched, the system may mal- function. If this occurs, consult your Toyota dealer.
  • Page 313 4-1. Maintenance and care NOTICE ■ To prevent paint deterioration and corrosion on the body and compo- nents (aluminum wheels etc.) ● Wash the vehicle immediately in the following cases: • After driving near the sea coast • After driving on salted roads •...
  • Page 314 4-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle's interior and keep it in top condition: ■ Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.
  • Page 315 4-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
  • Page 316 4-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use the following types of detergent, as they may discolor the vehi- cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye, and bleach •...
  • Page 317 It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
  • Page 318 Continue to press and hold the knob until the trip meter displays “000000”. ■ Allow inspection and repairs to be performed by a Toyota dealer ● Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.
  • Page 319 Booklet” “Owner’s Manual Supplement/Scheduled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment Items Check points Is the brake fluid at the correct...
  • Page 320 4-2. Maintenance Vehicle interior Items Check points • The accelerator pedal should Accelerator pedal move smoothly (without uneven pedal effort or catching). • Does the brake pedal move smoothly? • Does the brake pedal have appro- priate clearance from the floor? Brake pedal (→P.
  • Page 321 4-2. Maintenance Items Check points • Do the seat belts operate smoothly? Seat belts • The seat belts should not be dam- aged. • Do the seat controls operate Seats properly? • Does the steering wheel rotate smoothly? • Does the steering wheel have the Steering wheel correct amount of free play? •...
  • Page 322 4-2. Maintenance Vehicle exterior Items Check points • Do the doors and trunk operate Doors/trunk smoothly? • Does the engine hood lock sys- Engine hood tem work properly? • There should not be any signs of Fluid leaks fluid leakage after the vehicle has been parked.
  • Page 323 If the malfunction indicator lamp comes on The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. ■...
  • Page 324 Brake fluid level (→P. 358) • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology For the U.S.A.:...
  • Page 325 4-3. Do-it-yourself maintenance Items Parts and tools • “Toyota Genuine Motor Oil” or equivalent (→P. 352) Engine oil level • Rag or paper towel • Funnel (used only for adding engine oil) • Fuse with same amperage rating Fuses (→P. 384) as original •...
  • Page 326 4-3. Do-it-yourself maintenance CAUTION The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions: ■ When working on the engine compartment ● Make sure that the indicator on the “POWER”...
  • Page 327 4-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood release lever. STEP The hood will pop up slightly. Pull up the auxiliary catch STEP lever and lift the hood. CAUTION ■...
  • Page 328 4-3. Do-it-yourself maintenance Positioning a floor jack When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. Front CTY43AV171 Rear...
  • Page 329 4-3. Do-it-yourself maintenance CAUTION ■ When raising your vehicle Make sure to observe the following precautions to reduce the possibility of death or serious injury: ● Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.
  • Page 330 4-3. Do-it-yourself maintenance Engine compartment Fuse box (→P. 384) Power control unit coolant radiator (→P. 358) Engine oil filler cap (→P. 353) Condenser (→P. 358) Engine oil level dipstick Electric cooling fans (→P. 352) Engine coolant Brake fluid reservoir reservoir (→P.
  • Page 331 4-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil STEP Park the vehicle on level ground. After warming up the engine and turning off the hybrid system, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
  • Page 332 4-3. Do-it-yourself maintenance ■ Adding engine oil If the oil level is below or near the low level mark, add engine oil of the same type as that already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
  • Page 333 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.
  • Page 334 4-3. Do-it-yourself maintenance NOTICE ■ To prevent serious engine damage Check the oil level on a regular basis. ■ When replacing the engine oil ● Be careful not to spill engine oil on the vehicle components. ● Avoid overfilling, as the engine could be damaged. ●...
  • Page 335 4-3. Do-it-yourself maintenance Coolant Engine coolant reservoir The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold. Reservoir cap “F” line “L” line If the level is on or below the “L” line, add coolant up to the “F”...
  • Page 336 If the coolant level drops within a short time of replenishing Visually check the radiators, hoses, engine/power control unit coolant reser- voir caps, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling systems. CAUTION ■...
  • Page 337 Check the radiators and condenser and clear away any foreign objects. If either of the above parts is extremely dirty or you are not sure of their condition, have your vehicle inspected by your Toyota dealer. CAUTION ■ When the hybrid system is hot Do not touch the radiators or condenser as they may be hot and cause seri- ous injuries, such as burns.
  • Page 338 4-3. Do-it-yourself maintenance ■ Brake fluid can absorb moisture from the air Excess moisture in the brake fluid can cause a dangerous loss of braking efficiency. Use only newly opened brake fluid. CAUTION ■ When filling the reservoir Take care as brake fluid can harm your hands and eyes and damage painted surfaces.
  • Page 339 4-3. Do-it-yourself maintenance CAUTION ■ When adding washer fluid Do not add washer fluid when the hybrid system is hot or operating as washer fluid contains alcohol and may catch fire if spilled on the hybrid sys- tem etc. NOTICE ■...
  • Page 340 4-3. Do-it-yourself maintenance 12-volt battery ■ Location The 12-volt battery is located on the right-hand side of the luggage compartment. ■ Removing the 12-volt battery cover Remove the 12-volt battery cover. ■ Installing the 12-volt battery cover Install the cover Lift the tab to secure to the trunk liner...
  • Page 341 4-3. Do-it-yourself maintenance ■ Exterior Make sure that the 12-volt battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps. Terminals Hold-down clamp ■ Before recharging When recharging, the 12-volt battery produces hydrogen gas which is flam- mable and explosive.
  • Page 342 12-volt battery. Take extra care when connecting the 12-volt battery if the “POWER” switch mode prior to discharge is unknown. If the system will not start even after multiple attempts, contact your Toyota dealer. CAUTION ■...
  • Page 343 Use a 12-volt battery designed for this vehicle. Failure to do so may cause gas (hydrogen) to enter the passenger compartment, causing a fire or explo- sion. For replacement of the 12-volt battery, contact your Toyota dealer. NOTICE ■ When recharging the 12-volt battery Never recharge the 12-volt battery while the hybrid system is operating.
  • Page 344 ■ Tire rotation Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recom- mends that tire rotation is Front carried out at the same inter- val as tire inspection. ■...
  • Page 345 Have tire pressure warning valve and transmitter ID codes registered by your Toyota dealer. (→P. 367) ■ The tire pressure warning system must be initialized in the fol- lowing circumstances: ●...
  • Page 346 The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer.
  • Page 347 ● A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. ■ Replacing tires and wheels If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly.
  • Page 348 4-3. Do-it-yourself maintenance ■ Tire types ● Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
  • Page 349 Initialization can be completed in a few minutes. However, in the follow- ing cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ●...
  • Page 350 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
  • Page 351 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
  • Page 352 4-3. Do-it-yourself maintenance Tire inflation pressure ■ Tire inflation pressure The recommended cold tire inflation pressure and tire size are displayed on the tire and loading information label. (→P. 480)
  • Page 353 4-3. Do-it-yourself maintenance ■ Inspection and adjustment procedure Tire valve Tire pressure gauge STEP Remove the tire valve cap. STEP Press the tip of the tire pressure gauge onto the tire valve. STEP Read the pressure using the gauge gradations. STEP If the tire inflation pressure is not at the recommended level, adjust the pressure.
  • Page 354 Reduced driving comfort and tire life ● Reduced safety ● Damage to the drive train If a tire needs frequent inflating, have it checked by your Toyota dealer. ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ●...
  • Page 355 4-3. Do-it-yourself maintenance CAUTION ■ Proper inflation is critical to save tire performance Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury: ● Excessive wear ● Uneven wear ●...
  • Page 356 ● Bent wheels that have been straightened ■ Aluminum wheel precautions (if equipped) ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
  • Page 357 4-3. Do-it-yourself maintenance ■ When replacing wheels (vehicles with a tire pressure warning sys- tem) The wheels of your vehicle are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advance warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, tire pressure warning valves and trans- mitters must be installed.
  • Page 358 Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
  • Page 359 4-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method STEP Turn the “POWER” switch off. Open the glove box and STEP remove the glove box cover inside the glove box. Remove the filter cover.
  • Page 360 4-3. Do-it-yourself maintenance ■ Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) ■...
  • Page 361 4-3. Do-it-yourself maintenance Electronic key battery Replace the battery with a new one if it is depleted. ■ You will need the following items: ● Flathead screwdriver ● Small flathead screwdriver ● Lithium battery CR2032 ■ Replacing the battery Take out the mechanical key. STEP Remove the cover.
  • Page 362 4-3. Do-it-yourself maintenance ■ Use a CR2032 lithium battery ● Batteries can be purchased at your Toyota dealer, local electrical appli- ance shops or camera stores. ● Replace only with the same or equivalent type recommended by the manufacturer. ●...
  • Page 363 4-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. STEP Turn the “POWER” switch off. STEP Open the fuse box cover. Engine compartment (type A fuse box) Push the tabs in and lift the lid off.
  • Page 364 4-3. Do-it-yourself maintenance STEP After a system failure, see “Fuse layout and amperage rat- ings” (→P. 386) for details about which fuse to check. STEP Remove the fuse. Only type A fuse can be removed using the pullout tool. STEP Check if the fuse has blown.
  • Page 365 4-3. Do-it-yourself maintenance Type C Normal fuse Blown fuse Contact your Toyota dealer. Fuse layout and amperage ratings ■ Engine compartment (type A fuse box) Fuse block...
  • Page 366 4-3. Do-it-yourself maintenance Fuse block on the back of the cover Fuse Ampere Circuit METER-IG2 Gauge and meters 50 A Electric cooling fans H-LP CLN 30 A No circuit Multiport fuel injection system/ ENG W/PMP 30 A sequential multiport fuel injection system PTC HTR NO.2 50 A...
  • Page 367 4-3. Do-it-yourself maintenance Fuse Ampere Circuit R/B NO.2 50 A IGCT-MAIN, INV W/PMP 80 A Electric power steering S-HORN 7.5 A S-HORN DEICER 15 A No circuit HORN 10 A Horns Multiport fuel injection system/ EFI NO.2 15 A sequential multiport fuel injection system Multiport fuel injection system/ EFI NO.3...
  • Page 368 4-3. Do-it-yourself maintenance Fuse Ampere Circuit 15 A H-LP RH-LO Right-hand headlight (low beam) 20 A MNL H-LP 7.5 A Manual headlight leveling system Multiport fuel injection system/ EFI-MAIN NO.1 30 A sequential multiport fuel injection system, EFI NO.2, EFI NO.3 SMART Smart key system ETCS...
  • Page 369 4-3. Do-it-yourself maintenance ■ Engine compartment (type B fuse box) Fuse Ampere Circuit Hybrid system, electronic con- PM IGCT 7.5 A trolled transmission BATT VL SSR 10 A Hybrid system 7.5 A Hybrid system DC/DC IGCT 10 A Hybrid system INV W/PMP 7.5 A Hybrid system...
  • Page 370 4-3. Do-it-yourself maintenance ■ Under the instrument panel Fuse Ampere Circuit Shift lock control system, seat heaters, smart key system, tire pressure warning system, multiplex ECU-IG1 NO.2 10 A communication system, audio sys- tem, navigation system, moon roof, auto anti-glare inside rear view mir- ror, air conditioning system Electronically controlled brake sys- tem, electric cooling fans, stop...
  • Page 371 4-3. Do-it-yourself maintenance Fuse Ampere Circuit EPS-IG1 7.5 A Electric power steering ECU-IG1 NO.3 7.5 A Blind Spot Monitor S/HTR&FAN 10 A Seat heaters H-LP LVL 7.5 A No circuit WASHER 10 A Windshield wipers and washer Air conditioning system, PTC A/C-IG1 7.5 A heater...
  • Page 372 4-3. Do-it-yourself maintenance Fuse Ampere Circuit S/ROOF 10 A Moon roof P/SEAT FR 30 A Power seats 30 A No circuit Multiplex communication system, D/L-AM1 20 A power door lock, trunk opener switch TI&TE 20 A No circuit Occupant classification system, 10 A SRS airbag system ECU-IG2 NO.1...
  • Page 373 The fuses are designed to blow, protecting the wiring harness from damage. ■ When replacing light bulbs Toyota recommends that you use genuine Toyota products designed for this vehicle. Because certain bulbs are connected to circuits designed to prevent overload, non-genuine parts or parts not designed for this vehicle may be unusable.
  • Page 374 You may replace the following bulbs by yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
  • Page 375 4-3. Do-it-yourself maintenance ■ Rear bulb locations Rear turn signal light Back-up light Rear side marker light License plate lights Stop/tail light Replacing light bulbs ■ Headlights high beam and daytime running lights Turn the bulb base counterclock- STEP wise. Unplug connector while...
  • Page 376 4-3. Do-it-yourself maintenance ■ Headlight low beam (halogen bulb) Turn the bulb base counterclock- STEP wise. Unplug connector while STEP depressing the lock release. ■ Fog light (if equipped) Turn the steering wheel in the STEP opposite direction of the fog light that you wish to replace.
  • Page 377 4-3. Do-it-yourself maintenance Remove the fender liner clip. STEP After turning the clip, pull the clip until it stops. Turn the clip again, and then pull out the clip. Partly remove the fender liner STEP and unplug the connector while depressing the lock release.
  • Page 378 4-3. Do-it-yourself maintenance ■ Front turn signal/parking light Turn the bulb base counterclock- STEP wise. Remove the light bulb. STEP ■ Front side marker light Turn the bulb base counterclock- STEP wise.
  • Page 379 4-3. Do-it-yourself maintenance Remove the light bulb. STEP ■ Rear side marker light, rear turn signal light and stop/tail light Open the trunk lid and remove STEP the luggage trim cover clips. Pull the hook while depressing STEP The button the button.
  • Page 380 4-3. Do-it-yourself maintenance Turn the bulb base counterclock- STEP wise. Rear side marker light Rear turn signal light Stop/tail light Remove the light bulb. STEP Rear side marker light Rear turn signal light Stop/tail light ■ Back-up light Open the trunk lid and remove STEP the clips.
  • Page 381 4-3. Do-it-yourself maintenance Turn the bulb base counterclock- STEP wise. Remove the light bulb. STEP ■ License plate light Remove the lens. STEP Insert a properly sized Allen key into the hole of the lens, and pry off the lens as shown in the illus- tration.
  • Page 382 LED light bulbs The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. ■ Condensation build-up on the inside of the lens Contact your Toyota dealer for more information in the following situations.
  • Page 383 4-3. Do-it-yourself maintenance ■ Removing and installing the clips The luggage trim cover and trunk panel cover clip Removing Installing The fender liner clip Installing ■ When replacing light bulbs →P. 394 CAUTION ■ Replacing light bulbs ● Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights.
  • Page 384 ■ Discharge headlights (if equipped) ● Contact your Toyota dealer before replacing the discharge headlights (including light bulbs). ● Do not touch the discharge headlight’s high voltage socket when the head- lights are turned on.
  • Page 385 4-3. Do-it-yourself maintenance...
  • Page 386 5-1. Essential information Emergency flashers Use the emergency flashers if the vehicle malfunctions or is involved in an accident. Press the switch to flash all the turn signal lights. To turn them off, press the switch once again. NOTICE ■ To prevent 12-volt battery discharge Do not leave the emergency flashers on longer than necessary when the hybrid system is not operating.
  • Page 387 If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or flatbed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws.
  • Page 388 5-1. Essential information Towing with a wheel-lift type truck From the front Release the parking brake. From the rear Use a towing dolly under the front wheels. Using a flatbed truck If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°.
  • Page 389 5-1. Essential information NOTICE ■ To prevent causing serious damage to the transmission when towing using a wheel-lift type truck Never tow this vehicle from the rear with the front wheels on the ground. ■ To prevent damage to the vehicle when towing using a wheel-lift type truck When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle.
  • Page 390 5-1. Essential information If you think something is wrong If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms ● Fluid leaks under the vehicle (Water dripping from the air conditioning after use is normal.)
  • Page 391 However, if this continues to occur, have the vehicle inspected by your Toyota dealer. Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous. The following warning indicates a possible problem in the brake sys- tem.
  • Page 392 Indicates that the engine is almost overheating. (→P. 465) Have the vehicle inspected by your Toyota dealer immediately. Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident.
  • Page 393 5-2. Steps to take in an emergency Warning light Warning light/Details ABS warning light (U.S.A.) Indicates a malfunction in: • The ABS; or • The brake assist system. (Canada) Brake system warning light in yellow Indicates a malfunction in: • The regenerative brake system; or •...
  • Page 394 5-2. Steps to take in an emergency Follow the correction procedures. After taking the specified steps to correct the suspected problem, check that the warning light goes off. Warning light Warning light/Details Correction procedure Open door warning light (warning buzzer) Check that all doors and the Indicates that a door or the trunk are closed.
  • Page 395 • Flat tire (→P. 442) (U.S.A. only) pressure is adjusted, have the system checked by your Toyota dealer. When the light comes on after blinking for 1 minute: Have the system checked Malfunction in the tire by your Toyota dealer.
  • Page 396 The malfunction indicator lamp will go off after several driving trips. If the malfunction indicator lamp does not go off even after several trips, con- tact your Toyota dealer as soon as possible. ■ When the tire pressure warning light comes on (if equipped) Check the tire inflation pressure and adjust to the appropriate level.
  • Page 397 If there is a lot of snow or ice on the vehicle, particularly around the wheels or wheel housings ● If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.) ●...
  • Page 398 Customization that can be configured at Toyota dealer The vehicle speed linked seat belt reminder buzzer can be disabled. (Customizable features →P. 498) However, Toyota recommends that the seat belt reminder buzzer be operational to alert the driver and front passen- ger when seat belts are not fastened.
  • Page 399 5-2. Steps to take in an emergency CAUTION ■ If a blowout or sudden air leakage should occur (vehicles with a tire pressure warning system) The tire pressure warning system may not activate immediately. ■ Maintenance of the tires (vehicles with a tire pressure warning sys- tem) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the...
  • Page 400 5-2. Steps to take in an emergency CAUTION Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operat- ing properly. The TPMS (tire pressure warning system) malfunction indi- cator is combined with the low tire pressure telltale (tire pressure warning light).
  • Page 401 Multi-information display If any of the warning lights comes on again after the following actions have been performed, contact your Toyota dealer.
  • Page 402 A buzzer sounds and a warning message is shown on the multi-infor- mation display. The following warning indicates the possibility of dam- age to the vehicle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer. Warning message Details Indicates a malfunction in the hybrid system.
  • Page 403 A buzzer sounds and a warning message is shown on the multi-infor- mation display. Failure to investigate the cause of the following warn- ings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately. Warning message Details •...
  • Page 404 5-2. Steps to take in an emergency Follow the correction procedures. A buzzer sounds and a warning message is shown on the multi-infor- mation display. After taking the specified steps to correct the sus- pected problem, check that the warning message goes off. Warning message Details Correction procedure...
  • Page 405 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the hood is not fully closed. If the vehicle reaches a speed of 3 mph (5 Close the hood. km/h), flashes and a buzzer sounds to indicate that the hood is not yet fully closed.
  • Page 406 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates, if the vehi- cle reaches a speed of 3 mph (5 km/h), that Release the parking the parking brake is brake. (U.S.A.) still engaged. A buzzer also sounds. (Canada) (Flashes) Indicates that the...
  • Page 407 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that all maintenance accord- ing to the driven dis- tance on the maintenance sched- ule* should be per- If necessary, perform formed soon. maintenance. Comes on approxi- mately 4500 miles (U.S.A.
  • Page 408 5-2. Steps to take in an emergency Warning message Details Correction procedure When stopping the vehicle for a long period Indicates that the of time, shift the shift hybrid battery (trac- lever to P. The hybrid tion battery) is low battery (traction battery) A buzzer also sounds.
  • Page 409 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the EV drive mode is not available A buzzer also sounds. The reason the EV drive mode is not available (the vehicle Use the EV drive mode is idling, battery when it becomes avail- charge is low, speed is...
  • Page 410 5-2. Steps to take in an emergency Warning message Details Correction procedure Indicates that the “POWER” switch is turned off or turned to ACCESSORY mode Turn the lights off. and the driver's door is opened while the lights are turned on. (Flashes) A buzzer also sounds.
  • Page 411 5-2. Steps to take in an emergency Have the malfunction repaired immediately. After taking the specified steps to correct the suspected problem, check that the warning message and light go off. Interior Exterior Correction Warning message Details buzzer buzzer procedure The electronic key is not Start the hybrid...
  • Page 412 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure The electronic key was carried outside the vehicle and a door other than the driver's door Bring the elec- was opened tronic key back and closed into the vehicle.
  • Page 413 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure An attempt was made to exit the vehicle with the Turn the electronic key “POWER” Continuous and lock the switch off and Once doors without lock the doors first turning the again.
  • Page 414 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure The driver’s door was opened while any shift lever other than P Change the shift ⎯ Continuous was selected lever to P. without turning off the (Flashes) “POWER”...
  • Page 415 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure An attempt was made to lock the doors using Retrieve the the smart key electronic key Continuous system while from the vehi- Once the electronic cle and lock the key was still doors again.
  • Page 416 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure • When the doors were unlocked with the mechanical key and then the “POWER” switch was pressed, the electronic key Touch the elec- could not be tronic key to the detected in the “POWER”...
  • Page 417 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure Next time when starting the hybrid system, increase the Power was engine speed turned off due to slightly and ⎯ ⎯ the automatic maintain that power off func- level for approx- tion.
  • Page 418 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure The driver's door was opened and closed with the “POWER” switch turned off Press the and then the “POWER” “POWER” switch while switch was put depressing the in ACCES- brake pedal.
  • Page 419 5-2. Steps to take in an emergency Interior Exterior Correction Warning message Details buzzer buzzer procedure The “POWER” switch has been turned off with Change the shift ⎯ Once the shift lever in lever to P. a position other than P. (Flashes) After the “POWER”...
  • Page 420 5-2. Steps to take in an emergency If you have a flat tire Remove the flat tire and replace it with the spare provided. ■ Before jacking up the vehicle ● Stop the vehicle on a hard, flat surface. ● Set the parking brake. ●...
  • Page 421 5-2. Steps to take in an emergency Taking out the jack Remove the luggage floor cover STEP and spare tire cover. Remove the jack. STEP...
  • Page 422 5-2. Steps to take in an emergency Taking out the spare tire Remove the luggage floor cover STEP and spare tire cover. Remove the tool tray. STEP Loosen the center fastener that STEP secures the spare tire. When taking out or stowing the spare tire, make sure to firmly hold opposite ends of the tire.
  • Page 423 5-2. Steps to take in an emergency Replacing a flat tire Chock the tires. STEP Wheel Flat tire chock posi- tions Behind the Left- rear right- hand hand side side tire Front Behind the Right- rear left- hand hand side side tire In front of...
  • Page 424 5-2. Steps to take in an emergency Slightly loosen the wheel nuts STEP (one turn). Turn the tire jack portion “A” by STEP hand until the notch of the jack is in contact with the jack point. The jack point guides are located under the rocker panel.
  • Page 425 5-2. Steps to take in an emergency Remove all the wheel nuts and STEP the tire. When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface. Installing the spare tire Remove any dirt or foreign mat- STEP ter from the wheel contact sur-...
  • Page 426 5-2. Steps to take in an emergency When replacing an aluminum Tapered portion wheel with a steel wheel, tighten the wheel nuts until the tapered portion comes into loose contact with the disc wheel seat. Disc wheel seat Lower the vehicle. STEP Firmly tighten each wheel nut STEP...
  • Page 427 5-2. Steps to take in an emergency ■ The compact spare tire ● The compact spare tire is identified by the label “TEMPORARY USE ONLY” on the tire sidewall. Use the compact spare tire temporarily, and only in an emergency. ●...
  • Page 428 5-2. Steps to take in an emergency CAUTION ■ When using the compact spare tire ● Remember that the compact spare tire provided is specifically designed for use with your vehicle. Do not use your compact spare tire on another vehicle.
  • Page 429 5-2. Steps to take in an emergency CAUTION ■ Using the tire jack Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury. ● Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
  • Page 430 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • When installing the wheel nuts, be sure to install them with the...
  • Page 431 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and...
  • Page 432 5-2. Steps to take in an emergency If the hybrid system will not start Reasons for the hybrid system not starting vary depending on the situation. Check the following and perform the appropriate proce- dure: ■ The hybrid system will not start even though the correct starting procedure is being followed.
  • Page 433 ● One or both of the 12-volt battery terminals may be discon- nected. ● The 12-volt battery may be discharged. (→P. 461) Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. Emergency start function...
  • Page 434 (a system to pre- vent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to...
  • Page 435 5-2. Steps to take in an emergency If you lose your keys New genuine Toyota keys can be made by your Toyota dealer using the other key and the key number stamped on your key number plate.
  • Page 436 Unlocks all doors Turning the key rearward unlocks the driver’s door. Turning the key once again unlocks the other doors. Opens the windows and moon roof (turn and hold) * *: This setting must be custom- ized at your Toyota dealer.
  • Page 437 5-2. Steps to take in an emergency Starting the hybrid system STEP Ensure that the shift lever is in P and depress the brake pedal. Touch the Toyota emblem side of STEP electronic “POWER” switch. The “POWER” switch will turn to ON mode.
  • Page 438 5-2. Steps to take in an emergency ■ Stopping the hybrid system Shift the shift lever to P and press the “POWER” switch as you normally do when stopping the hybrid system. ■ Replacing the key battery As the above procedure is a temporary measure, it is recommended that the electronic key battery be replaced immediately when the battery is depleted.
  • Page 439 The following procedures may be used to start the hybrid system if the vehicle's 12-volt battery is discharged. You can also call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your vehicle by follow- ing the steps below.
  • Page 440 STEP Make sure the “READY” indicator comes on. If the indicator does not come on, contact your Toyota dealer. STEP Once the hybrid system has started, remove the jumper cables in the exact reverse order from which they were con- nected.
  • Page 441 5-2. Steps to take in an emergency ■ Charging the 12-volt battery The electricity stored in the 12-volt battery will discharge gradually even when the vehicle is not in use, due to natural discharge and the draining effects of certain electrical appliances. If the vehicle is left for a long time, the 12-volt battery may discharge, and the hybrid system may be unable to start.
  • Page 442 Do not allow children near the 12-volt battery. ■ After recharging the 12-volt battery Have the 12-volt battery inspected at your Toyota dealer as soon as possi- ble. If the 12-volt battery is deteriorating, continued use may cause the 12-volt battery to emit a malodorous gas, which may be detrimental to the health of passengers.
  • Page 443 Wait until the rightmost segment of the engine coolant tem- perature display stops flashing and returns to normal dis- play. Then stop the hybrid system. If the fans are not operating: Stop the hybrid system immediately and call your Toyota dealer.
  • Page 444 Water can be used in an emer- gency if engine coolant is unavail- (→P. 477) able. Have the vehicle inspected at the nearest Toyota dealer as soon as possible. ■ If “HYBRID SYSTEM OVERHEAT” is shown on the multi-infor- mation display...
  • Page 445 Water can be used in an emer- gency if power control unit cool- P. 477 ant is unavailable. (→ Have the vehicle inspected at the nearest Toyota dealer as soon as possible. ■ Overheating The following symptoms may occur when your vehicle is overheating: ●...
  • Page 446 5-2. Steps to take in an emergency CAUTION ■ To prevent an accident or injury when inspecting under the hood of your vehicle ● If steam is seen coming from under the hood, do not open the hood until the steam has subsided. The engine compartment may be very hot, caus- ing serious injury such as burns.
  • Page 447 5-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: STEP Stop the hybrid system. Set the parking brake and shift the shift lever to P.
  • Page 448 5-2. Steps to take in an emergency If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the following pro- cedure: STEP Steadily step on the brake pedal with both feet and firmly...
  • Page 449 Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is located on the...
  • Page 450 6-1. Specifications This number is also on the Certi- fication Label. ■ Engine number The engine number is stamped on the engine block as shown.
  • Page 451 6-1. Specifications Engine Model 2AR-FXE Type 4-cylinder in line, 4-cycle, gasoline 3.54 × 3.86 in. (90.0 × 98.0 mm) Bore and stroke Displacement 152.2 cu.in. (2494 cm Valve clearance Automatic adjustment (engine cold) Fuel Fuel type Unleaded gasoline only Octane rating 87 (Research Octane Number 91) or higher Fuel tank capacity 17.0 gal.
  • Page 452 5 minutes, and check the oil level on the dipstick. ■ Engine oil selection “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity.
  • Page 453 6-1. Specifications Oil viscosity (0W-20 is explained here as an example): • The 0W in 0W-20 indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather. •...
  • Page 454 Power control 3.4 qt. (3.2 L, 2.8 Imp. qt.) unit Use either of the following: • “Toyota Super Long Life Coolant” • A similar high-quality ethylene glycol-based non-sili- Coolant type cate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
  • Page 455 *: The fluid capacity is a reference quantity. If replacement is necessary, con- tact your Toyota dealer. NOTICE ■ Transmission fluid type Using transmission fluid other than “Toyota Genuine ATF WS” may ulti- mately damage the transmission of your vehicle.
  • Page 456 6-1. Specifications Brakes Pedal clearance 3.62 in. (92 mm) 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) Pedal free play Brake pad wear limit 0.04 in. (1.0 mm) Parking brake lining wear limit 0.04 in. (1.0 mm) ⎯ 10 clicks Parking brake pedal travel Fluid type SAE J1703 or FMVSS No.116 DOT 3...
  • Page 457 6-1. Specifications Steering Free play Less than 1.2 in. (30 mm) Tires and wheels 16-inch tires Tire size P205/65R16 94S, T155/70D17 110M Driving under normal conditions Front: 35 psi (240 kPa, 2.4 kgf/cm or bar) Rear: 35 psi (240 kPa, 2.4 kgf/cm or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm...
  • Page 458 6-1. Specifications 17-inch tires Tire size P215/55R17 93V, T155/70D17 110M Driving under normal conditions Front: 35 psi (240 kPa, 2.4 kgf/cm or bar) Rear: 35 psi (240 kPa, 2.4 kgf/cm or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm or bar) Tire inflation pressure Driving at high speeds (above 100 mph [160 (Recommended cold tire...
  • Page 459 6-1. Specifications Light bulbs Light Bulbs Bulb No. Type Headlights ⎯ Low beam (halogen bulbs)* ⎯ Low beam (discharge bulbs)* High beam 9005 Front side marker ⎯ lights Rear side marker ⎯ Exterior lights Front turn signal/park- ⎯ 28/8 ing lights ⎯...
  • Page 460 In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer. ■...
  • Page 461 ■ Recommendation of the use of gasoline containing detergent additives ● Toyota recommends the use of gasoline that contains detergent additives to avoid the build-up of engine deposits. ● All gasoline sold in the U.S.A. contains detergent additives to clean and/ or keep clean intake systems.
  • Page 462 Non-recommendation of the use of gasoline containing MMT Some gasoline contains an octane enhancing additive called MMT (Methyl- cyclopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected.
  • Page 463 6-1. Specifications Tire information Typical tire symbols Full-size tire Compact spare tire Tire size (→P. 489) DOT and Tire Identification Number (TIN) (→P. 488) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators (→P.
  • Page 464 6-1. Specifications Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL”...
  • Page 465 6-1. Specifications Typical DOT and Tire Identification Number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer's identifica- tion mark Tire size code Manufacturer's optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal...
  • Page 466 6-1. Specifications Tire size ■ Typical tire size information The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits) Speed symbol...
  • Page 467 U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. ■ DOT quality grades All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades.
  • Page 468 6-1. Specifications ■ Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1 - 1/2) times as well on the government course as a tire graded 100.
  • Page 469 6-1. Specifications Warning: The temperature grades of a tire assume that it is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. Glossary of tire terminology Tire related term Meaning Tire pressure when the vehicle has been...
  • Page 470 6-1. Specifications Tire related term Meaning 150 lb. (68 kg) times the number of occupants Normal occupant specified in the second column of Table 1 that weight follows Distribution of occupants in a vehicle as speci- Occupant distribution fied in the third column of Table 1 below The combined weight of installed regular pro- duction options weighing over 5 lb.
  • Page 471 6-1. Specifications Tire related term Meaning The surface area of the rim not covered by the Weather side inflated tire The part of the tire that is made of steel wires, Bead wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components Bead separation...
  • Page 472 6-1. Specifications Tire related term Meaning The parting of the innerliner from cord material Innerliner separation in the carcass (a) The sidewall that contains a whitewall, bears white lettering, or bears manufac- turer, brand, and/or model name molding that is higher or deeper than the same Intended outboard molding on the other sidewall of the tire, or sidewall...
  • Page 473 6-1. Specifications Tire related term Meaning A layer of rubber-coated parallel cords A parting of rubber compound between adja- Ply separation cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, Pneumatic tire when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load...
  • Page 474 6-1. Specifications Tire related term Meaning That portion of a tire that comes into contact Tread with the road A tread section running circumferentially Tread rib around a tire Tread separation Pulling away of the tread from the tire carcass The projections within the principal grooves Treadwear indicators designed to give a visual indication of the...
  • Page 475 Toyota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Customizable Features Vehicles with a Display Audio system: Settings that can be...
  • Page 476 6-2. Customization Default set- Customized Item Function ting setting Operation sig- — (Emergency flashers) Operation sig- — — (Buzzer) Smart key Operation system and Level 5 Off to level 7 buzzer volume wireless remote Time elapsed control before auto- → P. 53, matic door lock function is acti- 60 seconds...
  • Page 477 6-2. Customization Default set- Customized Item Function ting setting Wireless — — remote control Driver's door unlocked in All doors Unlocking one step, all unlocked in operation doors one step. unlocked in Wireless two steps remote control Panic function — —...
  • Page 478 6-2. Customization Default set- Customized Item Function ting setting Driver's door unlocked in All doors Unlocking one step, all unlocked in — using a key doors one step. unlocked in two steps Speed-detect- ing automatic door lock func- tion Door lock Opening →...
  • Page 479 6-2. Customization Default set- Customized Item Function ting setting Time elapsed before lights 15 seconds 7.5 seconds — turn off 30 seconds Operation when the doors — — are unlocked Illumination Operation after → P. 286) the “POWER” — — switch turned Operation when you...
  • Page 480 6-2. Customization Default set- Customized Item Function ting setting Key linked — — opening Wireless Power win- remote control — — linked opening (driver’s door) & Key linked clos- — — moon roof → P. 97, Wireless 100) remote control —...
  • Page 481 6-3. Initialization Items to initialize The following items must be initialized for normal system operation after such cases as the 12-volt battery being reconnected, or mainte- nance being performed on the vehicle: Item When to initialize Reference Maintenance data After the maintenance is performed P.
  • Page 482 If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
  • Page 483 Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité...
  • Page 484 ■ Ceinture de sécurité arrière Si la ceinture de sécurité est sortie de son guide, repassez-la dedans avant de l'utiliser. Entretien et soin ■ Ceintures de sécurité Nettoyez avec un chiffon ou une éponge humectée d'eau savonneuse tiède. Profitez de l'occasion pour vérifier régulièrement que les ceintures ne sont pas effilochées, entaillées, ou ne paraissent pas exagérément usées.
  • Page 485 SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English. Sacs de sécurité...
  • Page 486 Sacs de sécurité gonflables SRS latéraux et rideau Sacs de sécurité gonflables SRS latéraux avant Participent à la protection du haut du corps des occupants assis aux places avant Sacs de sécurité gonflables SRS latéraux arrière Participent à la protection du haut du corps des occupants assis aux places arrière extérieures Sacs de sécurité...
  • Page 487 Composition du système de sacs de sécurité gonflables SRS Capteurs d'impact avant Témoins indicateurs “AIR BAG ON” et “AIR BAG Système de classification OFF” des occupants du siège passager avant (ECU et Témoin d'alerte SRS capteurs) Contacteur de boucle de Sac de sécurité...
  • Page 488 Votre véhicule est équipé de SACS DE SECURITE GONFLABLES INTELLIGENTS (ADVANCED AIRBAGS) conçus selon les normes de sécurité américaines applicables aux véhicules à moteur (FMVSS208). Le boîtier électronique (ECU) des sacs de sécurité gonflables régule le déploiement de ces derniers sur la base des informations qu'il reçoit des capteurs, etc., indiqués ci-dessus dans le schéma illustrant la composition du système.
  • Page 489 ATTENTION ■ Précautions avec les sacs de sécurité gonflables SRS Respectez les précautions suivantes concernant les sacs de sécurité gonflables SRS. À défaut, des blessures graves, voire mortelles, pourraient s'ensuivre. ● Le conducteur et tous les passagers à bord du véhicule doivent porter leur ceinture de sécurité...
  • Page 490 être grièvement blessés ou tués par le déploiement d'un sac de sécurité gonflable. Installez dans un siège de sécurité enfant les enfants trop jeunes pour pouvoir utiliser la ceinture de sécurité. Toyota recommande vivement que les nourrissons et les jeunes enfants soient installés sur le siège arrière du véhicule et convenablement attachés.
  • Page 491 ATTENTION ■ Précautions avec les sacs de sécurité gonflables SRS ● N'installez jamais un siège de sécurité enfant type dos à la route sur le siège passager avant, même si le témoin indicateur “AIR BAG OFF” est allumé. En cas d'accident, par la violence et la vitesse de son déploiement, le sac de sécurité...
  • Page 492 ATTENTION ■ Précautions avec les sacs de sécurité gonflables SRS ●Interdisez à quiconque de s'agenouiller sur les sièges passagers en appui contre la porte ou de sortir la tête ou les mains à l'extérieur du véhicule. ●Ne fixez ni ne posez aucun objet sur la planche de bord, la garniture centrale du moyeu de volant de direction et la partie inférieure du tableau de bord.
  • Page 493 ● Si les parties renfermant les sacs de sécurité gonflables SRS, telles que la garniture du moyeu de volant et les garnitures de montants avant et arrière, apparaissent abîmées ou craquelées, faites-les remplacer par votre concessionnaire Toyota.
  • Page 494 Modification et mise au rebut des éléments du système de sacs de sécurité gonflables SRS Consultez impérativement votre concessionnaire Toyota si vous avez besoin d'intervenir sur votre véhicule ou de procéder à l'une des modifications suivantes. Les sacs de sécurité gonflables SRS risquent de ne pas fonctionner correctement ou de se déployer (gonfler) accidentellement,...
  • Page 495 What to do if... What to do if... If you have a flat tire A tire punctures P. 442 P. 454 If the hybrid system will not start P. 108 Immobilizer system If the vehicle’s 12-volt battery is The hybrid system does not P.
  • Page 496 What to do if... The vehicle is stuck in If the vehicle becomes stuck P. 469 mud or sand If a warning light turns on or a A warning light or indicator light P. 413 warning buzzer sounds... comes on...
  • Page 497: Warning Lights

    What to do if... ■Warning lights Brake system warning Slip indicator light light (red indicator) P. 414 Tire pressure warning system light P. 413 P. 416 Brake system warning light Electric power steering sys- (yellow indicator) tem warning light P. 414 P.

Table of Contents

Save PDF