Fcc And Ic Interference Requirements; For Industry Canada User - Siemens EcoView Installation Instructions Manual

Document No. 129-566
Installation Instructions
December 13, 2011
FCC and IC Interference
Requirements
"This device complies with Part 15 of the FCC Rules
and with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two
conditions (1) this device may not cause harmful
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device."
« Ce dispositif est conforme à la partie 15 des règles
de FCC et aux normes permis-exemptes du Canada
RSS d'industrie. L'opération est sujette aux deux
conditions suivantes (1) que ce dispositif peut ne
pas causer l'interférence nocive, et (2) ce dispositif
doit accepter n'importe quelle interférence, y
compris l'interférence qui peut causer le
fonctionnement peu désiré du dispositif. »
Per RSS-Gen Issue 3 (December 2010 Section 7.1.3)
FCC Note
This device complies with Part 15 of the FCC rules.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate the equipment.
FCC and IC Radiation Exposure
Statement for Mobile Devices
"This equipment complies with FCC and IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and
operated with minimum distance 20cm between the
radiator and your body. This transmitter must not be
re-located or operating in conjunction with any other
antenna or transmitter."
(For compliance with FCC Code of Federal
Regulations Title 47 Part 2.1093)
FCC Code of Federal Regulations Title
47 Part 15.105
Information to the user:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and
models as design improvements are introduced. EcoView is a trademark of Siemens Industry, Inc. Other product or company names
mentioned herein may be the trademarks of their respective owners. © 2014 Siemens Industry, Inc.
Siemens Industry, Inc.
Building Technologies Division
Retail and Commercial Systems
1000 Deerfield Parkway
Buffalo Grove, IL 60089-4513
USA
+1 847-215-1000
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
•
•
•

For Industry Canada User

"This Class B digital apparatus complies with
Canadian ICES-003 Issue 4 (February 2004)."
« Cet appareillage numérique de la classe B est conforme
ICES-003 à l'issue canadienne 4 (le février 2004). »
Antenna
"Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication."
« Aux termes des règlements du Canada d'industrie, cet
émetteur radioélectrique peut seulement fonctionner
utilisant une antenne d'un type et (ou moins) d'un gain
maximum approuvés pour l'émetteur par Industry Canada.
Pour ramener des interférences radio potentielles à
d'autres utilisateurs, on devrait ainsi choisir le type
d'antenne et son gain que l'équivalent a isotropically
rayonné la puissance (e.i.r.p.) n'est pas plus que celui
nécessaire pour la communication réussie. »
For EcoView system support, please call
1 + 877-306-9400
Your feedback is important to us. If you have
comments about this document, please send
them to SBT_technical.editor@siemens.com
Reorient or relocate receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
Document No. 129-566
Printed in the USA
Page 8 of 8