Subscribe to Our Youtube Channel
Related Manuals for SATA jet3000 K
Summary of Contents for SATA jet3000 K
- Page 1 ® SATAjet 3000 K spray mix Betriebsanleitung - Operating Instructions Betriebsanleitung - Operating Instructions Mode d‘emploi...
- Page 2 US 7.018.154...
- Page 3 Trade Associations, etc.). SATA, SATAjet, the SATA Logo and/or other SATA products referenced herein are either registered trademarks or trademarks of SATA GmbH & Co. KG in the U.S. and/or other countries. The names of companies and products mentioned herein may be the trademarks of their respective owners.
-
Page 4: Functional Description
• Flat fan 120 Nl/min/4.2 cfm at 3 bar/43.5 psi • Round fan 310 Nl/min/10.9 cfm at 3 bar/43.5 psi Further product range and accessories • Filter system SATA filter 400 • Respirators (half masks and full face respirators) • Material pump 14:1 • Material pump 32:1... - Page 5 For servicing/repair work of any kind, the system must be devoid of pressure, i.e. disconnected from the air supply. Failure to respect this safety warning may result in damage and injuries, even death at worst. SATA does not take any responsibility for possible results of such failure.
- Page 6 Operating Instructions SATAjet 3000 K spray mix Note: - Micrometer in vertical position (position III - parallel to the gun body) = maximum atomization and maximum internal spray gun pressure (identical with spray gun inlet pressure) - Position I or II (across gun body) = minimum atomization, minimum internal spray gun pressure (for spot repair, speckling etc.) Attention: While the spray gun is connected to the air supply, the air micro- meter fixing screw, pos.
- Page 7 Use punched hexagon socket (SW12) of the universal wrench for the paint nozzle. Using components of other manufacturers may result in a reduction in quality and the SATA Warranty expires or it may be hazardous to your health. 7. Changing the self-adjusting seals a) Material side: The paint needle is sealed by a self-adjusting Teflon sealing.
- Page 8 Insert new air distribution ring in its correct position and tighten paint nozzle again. Respect mounting instructions for the air distribution ring (see 6.1)! e) Slightly oil movable parts with SATA special grease (Art. No. 10009). Should the material connection 98608 in the spray gun body loosen when removing the material tube 98590, respectively, please proceed as follows: • Remove material connection 98590 completely...
- Page 9 Operating Instructions SATAjet 3000 K spray mix 8.1 Repair instructions for air distribution ring Important Notes: When pulling off the air distribution ring make sure that the sealing edges inside the gun body are not damaged. Therefore please proceed with utmost care when removing the air distribution ring ! 1.
- Page 10 - needle sealing damaged or lost Spray pattern Horn air holes or air circuit Soak in thinner/cleaning in sickle shape clogged fluid, afterwards clean with SATA nozzle cleaning needle Drop-like or oval Dirt on fluid pin tip or air circuit Turn air nozzle by 180 shaped pattern clogged degrees. If defective...
- Page 11 18341 Pressure spring for paint needle 30833 Nozzle cleaning kit 74856 Kit of SATA sieves 200 msh, consisting of 4 sieves 20933, 2 strainer holder 77503 and 1 screw 26393 94961 Air micrometer, cpl. 97824 Pack of 3 air distribution rings...
- Page 12 Operating Instructions SATAjet 3000 K spray mix Nozzle identification: SATAjet 3000 K spray mix Paint nozzle A Technical data Sieve Inversion nozzle B Nozzle Art. No. Nozzle Art. No. ø mm ø Zoll Angle Width l/min at ø mm/ Art. No. 70 bar µm 1840...
- Page 13 Returned merchandise to SATA must be sent prepaid. All service charges, freight and handling charges are to be paid by the consumer. The charges made will be in accordance with the currently existing pricing. Suretyships may not prolong the warranty period.
- Page 14 98699 Gewicht Weight with Poids avec SATAjet 3000 K spray mix 650 g...
- Page 15 SATA GmbH & Co. KG Domertalstr. 20 70806 Kornwestheim Tel. +49 71 54 811 - 0 Fax +49 71 54 811 - 196 www.sata.com...
Need help?
Do you have a question about the jet3000 K and is the answer not in the manual?
Questions and answers