Advertisement
FEA TURE
A CTION TO PERFORM
To
Turn the Ignition Switch ON
Enter
Toggle the Valet/Program/M anual Override Switch
The
ON then OFF 3 Times
Programming Within 3 seconds,
M ode
turn the Ignition Switch OFF, then ON
You have now engaged the Programming M ode, and are set to adjust the First feature
This mode will time out automatically in 15 seconds, or can be cancelled by turning the Ignition Switch OFF
First
Press Transmitter Button 1 to Change Feature
OR Toggle the Valet/Program/M anual Override Switch once to Advance to the next feature
Second
Press Transmitter Button 1 to Change Feature
OR Toggle the Valet/Program/M anual Override Switch once to Advance to the next feature
Third
Press Transmitter Button 1 to Change Feature
OR Toggle the Valet/Program/M anual Override Switch once to Advance to the next feature
Fourth
Press Transmitter Button 1 to Change Feature
OR Toggle the Valet/Program/M anual Override Switch once to Advance to the next feature
Fifth
Press Transmitter Button 1 to Change Feature
OR Toggle the Valet/Program/M anual Override Switch once to Advance to the next feature
Sixth
Press Transmitter Button 1 to Change Feature
OR Toggle the Valet/Program/M anual Override Switch once to Advance to the next feature
Seventh
Press Transmitter Button 1 to Change Feature
NOTE: If you accidentally toggled past the feature you intended to adjust, you must exit and re-enter the mode.
NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between steps, or
the programming mode will be terminated.
COMPLETING THE INSTALLATION:
After you have confirmed the operation of the PRO 9845, and tested any and all optional features of the system:
1. Mount the control module up and behind the dash securing it in place with cable ties or screws. Be certain that
the chosen mounting location will not inhibit any of the controls of the vehicle.
2. Securely harness and tie all wiring up and away from all hot and moving parts that they may come in contact with
under the dash board or in the engine compartment areas.
CAUTION: Particularly avoid the area around the steering shaft and column, as wires can wrap around these
mechanisms and impair the safe operation of the vehicle.
3. Check the vehicle's wipers, lights, horn, etc... to insure proper operation.
4. Replace all panels that were removed during installation, and retest the system.
5. Explain the operation of the system and its various features to the end user if available, and place the Owner's
Manual on the dashboard for them to find and review.
OR Turn the Ignition Switch OFF to exit the Programming M ode
RESPONSE FROM SYSTEM
LED Turns OFF
1 Siren/Horn Chirp & 1 LED Flash
1 Short Chirp, and 1 Long Chirp
1 Chirp = Passive Arming ON
2 Chirps = Active Arming ON
1 Chirp = Ign Locking ON
2 Chirps = Ign Locking OFF
1 Chirp = Ign Unlocking ON
2 Chirps = Ign Unlocking OFF
1 Chirp = Chirps ON
2 Chirps = Chirps OFF
1 Chirp = Passive Doorlock ON
2 Chirps = Passive Doorlock OFF
1 Chirp = Steady Output (siren)
2 Chirps = Pulsed Output (horn)
1 Chirp = 800ms Lock Pulse
2 Chirps = 3.5sec Lock Pulse
3 Chirps = 800ms Lock Pulse
800ms Double Unlock
7
LED FLA SH PA TTERN
1 Flash, Pause, Repeat
2 Flashes, Pause, Repeat
3 Flashes, Pause, Repeat
4 Flashes, Pause, Repeat
5 Flashes, Pause, Repeat
6 Flashes, Pause, Repeat
7 Flashes, Pause, Repeat
Advertisement
