WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN 10.70MHz THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. blue 10.67MHz REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE orange 10.73MHz PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Page 3
SECTION 1 This section is extracted from GENERAL instruction manual. – 3 –...
SECTION 2 DISASSEMBLY The equipment can be remo ved using the f ollo wing pr ocedure . Cabinet (rear) Power board AC IN board AMP board Main board, Key board Note : Follow the disassembly procedure in the numerical order given. 2-1.
2-5. SETTING THE POINTER 1 Turn the drum (B) in the direction of A until it stopped. 2 Insert the rack (pointer) into the chassis groove. 3 Install the pointer 4 Slid the pointer and align it with the groove on the scribed Scribed line Pointer...
SECTION 3 ELECTRICAL ADJUSTMENTS 3-1. MW SECTION LW FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. BAND switch : MW 145kHz AM RF signal < confirmation > 265kHz Put the lead-wire generator antenna close to the set. LW TRACKING ADJUSTMENT Adjust for a maximum reading on level meter.
Page 8
• Connecting Digital Voltmeter • Repeat the procedures in each adjustment several times, and the frequency coverage and tracking adjustments should be finally – MAIN board (Conductor side) – digital voltmeter done by the trimmer capacitors. Main board TP2 (VT) FM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter.
ICF-1000L 4-4. SCHEMATIC DIAGRAMS Waveform (Band : FM) 12 Vp-p VOLT/DIV : 5 V AC Q101 C TIME/DIV : 1 msec Note: • All capacitors are in µF unless otherwise noted. pF: µµF • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.
SECTION 5 EXPLODED VIEWS NOTE : • -XX, -X mean standardized parts, so they • The mechanical parts with no reference may have some difference from the original number in the exploded views are not The components identified by mark 0 one.
5-2. FRONT CABINET SECTION T401 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-047-923-01 WOOD (C), SIDE(GRAY) 3-047-936-11 WOOD (A), SIDE(BROWN) 3-047-923-11 WOOD (C), SIDE(BROWN) 3-043-336-01 SHAFT (TUNING)
AC IN AMPLIFIER SECTION 6 ELECTRICAL PARTS LIST MAIN NOTE : • Due to standardization, replacements in the • SEMICONDUCTORS In each case, u : µ , for example : The components identified by mark 0 parts list may be different from the parts uA..
Page 17
MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < BAND PASS FILTER > C207 1-107-826-11 CERAMIC CHIP 0.1uF C208 1-107-826-11 CERAMIC CHIP 0.1uF BPF1 1-236-022-11 FILTER, BAND PASS C209 1-107-826-11 CERAMIC CHIP 0.1uF < CAPACITOR > C501 1-164-489-11 CERAMIC CHIP 0.22uF...
Page 18
MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < JUMPER > Q101 8-729-120-28 TRANSISTOR 2SC1623-L5L6 1-216-296-91 SHORT Q102 8-729-800-71 TRANSISTOR 2SB815B7-TB 1-216-296-91 SHORT Q103 8-729-027-60 TRANSISTOR DTC144TKA-T146 1-216-864-11 METAL CHIP 1/16W Q201 8-729-027-60 TRANSISTOR DTC144TKA-T146 1-216-296-91 SHORT Q202 8-729-027-39 TRANSISTOR DTA144TKA-T146...
Page 19
ICF-1000L MAIN POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R221 1-216-833-11 METAL CHIP 1/16W D403 8-719-031-85 DIODE 1N4002L R501 1-216-821-11 METAL CHIP 1/16W D404 8-719-031-85 DIODE 1N4002L R502 1-216-833-11 METAL CHIP 1/16W R503 1-216-833-11 METAL CHIP 1/16W <...