Advertisement
Your Alarm and or Remote Start unit has a configurable receiver that allows
the transmitter to be programmed to operate the Lock Unlock functions with
one transmitter button or with two transmitter buttons (separate Lock/
Unlock). In addition, the receiver also allows driver priority function. This
driver priority function takes place when ever a particular transmitter is
used to unlock the vehicle regardless of the selection of one button or two
button operation.
The following indicates the receiver programmable slots.
1 Lock/Unlock or Lock
2 Unlock if Programmed
3 Trunk Release & or Remote Start (Optional on some models)
4 Auxiliary Output
5 Auxiliary Output
6 Driver 1 Priority or Sperate Output
7 Driver 2 Priority or Separate Output
Receiver channels 6 or 7 will accept the programming of transmitter
channel 1 if used as the Lock/Unlock button, or Channel 2 when separate
Lock Unlock buttons are programmed. In this way, whenever the transmit-
ter is used to unlock the vehicle, channel 6 or 7, when programmed, will
provide a pulsed ground output. This output can be connecter to the driver
priority function of the vehicle to reset preset user features. Please consult
with your installation center's technician to see if this feature is available in
your vehicle.
NOTE: A total of 4 transmitters may be programmed into any receiver
channel. Two two way and two one way or four one way transmitter
combinations only.
Force programming a transmitter, removing a transmitter, or reprioritizing a
transmitter is covered later in this manual.
Also, if you do not program a transmitter button into channel 2 which is the
separate unlock/disarm channel, then whatever button is programmed into
channel 1 will serve as both lock/arm & unlock/disarm.
Note: The "F" Button serves as a function button in combination with other
buttons explained in your owners manual. This button may not be used to
operate a receiver channel.
NOTE: The Option Button is predetermined and programmed for access to
Time Start, and Temperature Start & Check so it cannot be used for multiple
button operation of any other feature. It will however operate for any single
button programming.
This transmitter is also capable of one button programming for certain model
Audiovox Alarms. If your alarm is one of these models, then when step 3 is
Rev "a" To Indicate PBLED 7/06
Model UTX-ETX
Programming Guide
128-7400A
1 of 8
Advertisement
Related Manuals for Audiovox UTX-ETX
Summary of Contents for Audiovox UTX-ETX
- Page 1 It will however operate for any single button programming. This transmitter is also capable of one button programming for certain model Audiovox Alarms. If your alarm is one of these models, then when step 3 is Rev “a” To Indicate PBLED 7/06 Programming Guide...
- Page 2 THIS PAGE LEFT BLANK INTENTIONALLY 128-7400A 2 of 8...
-
Page 3: To Enter The Program Mode
completed on the following page, you can turn the ignition switch off and programming with the default button configurations for the first four chan- nels will be complete. TO ENTER THE PROGRAM MODE: Note: Some systems may use a combination push-button LED switch. In these systems the push-button and the dash mounted LED are one and the same. - Page 4 transmitter you wish to control Channel 4 output, (Auxiliary Output 1) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 4 output) 10. Within 10 seconds, press and release the valet program switch one time.
-
Page 5: Replacing The Battery
(Repeat this for each transmitter you wish to remain stored in the control unit). The receiver stores up to four transmitters. To be certain all transmitter slots in the receiver are occupied with transmitters you wish to continue to use, and all others are erased, you will have to fill all four receiver slots. If in step 3 you identified one transmitter, you will have to fill the additional 3 slots. - Page 6 recommended at least every 6 to 8 months, depending upon how frequently the transmitter is used. To replace the transmitter battery: 1. Slide back the lock tab on the back side of the transmitter case in the direction shown on the following page. 2.
- Page 7 8) Mail this form along with your payment to: Transmitter Ordering Department Audiovox Corporation 150 Marcus Blvd., Hauppauge N.Y. 11788 Credit card purchasers can order additional or replacement transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and follow the instructions from the operator interface $99.00...
- Page 8 © 2006 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-7400A 128-7400A 8 of 8...