Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Venini VEO9002
Summary of Contents for Venini VEO9002
- Page 1 ELECTRIC SINGLE OVENS USER AND INSTALLATION INSTRUCTIONS...
-
Page 2: Model Number
For future reference please record the following information which be found on the Rating Plate and the date of purchase which can be found in the invoice: Model Number ……………………. Serial Number ……………………. Date of Purchase ……………………. -
Page 3: Table Of Contents
CONTENTS page 3 General Information pages 4-5 Warning and Safety Instructions pages 6-9 Instructions for Use Instructions for Installation pages 10-12 Technical Data page 13... - Page 4 Dear Customer, Congratulations on purchasing your new product from Think Appliances. To register your parts and labour warranty (some conditions apply please refer to your warranty card for more details) please contact out Customer Care team on: 1800 444 357 Our Customer Care centre is there to ensure you get the most out of your appliance.
-
Page 5: General Information
GENERAL INFORMATION Please read this booklet thoroughly before you use this appliance. It is important that you understand all the control functions before commencing to cook with your new appliance. Please remember the advice and warnings shown on page 5 which is headed ‘IMPORTANT –... -
Page 6: Warning And Safety Instructions Pages
IMPORTANT NOTE – WARNING AND SAFETY INSTRUCTIONS Warning: this appliance must be earthed. This appliance complies with all current European safety legislation, however the producer do wish to emphasise that compliance does not remove the fact that the appliance surfaces will become hot during use and retain heat after operation. - Page 7 NOTE: This appliance must be correctly installed by a suitably qualified person, strictly in accordance with the manufacturer’s instructions. The producer declines any responsibility for injury or damage to persons or property as a result of improper use or installation of this appliance. Heat, steam and moisture will be created during use, take care to avoid injury and ensure that the room is adequately ventilated.
-
Page 8: Instructions For Use Pages
These User Instructions should be retained for future reference and for use by a person who is perhaps unfamiliar with the appliance. The following models are covered by these instructions: VEO9002 USING THE OVEN Before your ovens first use it is suggested to do a “burn in”. This involves turning the oven onto the fan oven setting at 200°C for 15 minutes, then select the conventional mode for a further 15 minutes. -
Page 9: Helpful Hints
WARNING • Keep the oven door CLOSED when using the GRILL. • Do not use aluminium foil to cover the grill pan or heat items wrapped in aluminium foil under the grill – the high reflectivity of the foil can damage the grill element. •... - Page 10 120 minutes cut-off timer The function of the programming timer is to turn on the oven for a pre-determined amount of time. Operating: After having set the oven, switch knob at the desired temperature, turn the timer knob in a clockwise direction to the desired cooking time (max. 120 minutes). when the timer will return to position "0", a minute counter ringing will advise that the oven will automatically turn off.
-
Page 11: Cleaning The Appliance
CLEANING THE APPLIANCE Always allow the appliance to cool down before cleaning to avoid a burn injury. Do not use caustic or abrasive agents, coarse wire wool or hard tools as these can damage the surface finishes. Normally, wiping with a soft cloth dampened with hot detergent is sufficient, but for stubborn marks the following is recommended: VITREOUS ENAMEL PARTS Use only a cleaner that is recommended for this type of material –... -
Page 12: Instructions For Installation Pages
INSTALLATION INSTRUCTIONS INSTRUCTIONS FOR INSTALLATION This appliance must be installed by a competent person, in accordance with the current version of the Regulations and Safety Standards or your local Regulations and Safety Standards: Building Regulations (issued by the Department of Environment) Building Standards (issued by the Scottish Development Department) IEE Wiring Regulations Electricity at Work Regulations... -
Page 13: Installation Instructions
INSTALLATION INSTRUCTIONS ELECTRICAL CONNECTION Before connecting the appliance, make sure the supply voltage marked on the Rating Plate corresponds with the mains supply voltage. WARNING – THIS APPLIANCE MUST BE EARTHED This appliance should be wired into a 16A circuit ensuring compliance with AS/NZS 3000 wiring rules. IMPORTANT The wires in the mains supply lead are coloured in accordance with the following code: Green and Yellow... -
Page 14: Replacing The Oven Light
INSTALLATION INSTRUCTIONS REPLACING THE OVEN LIGHT (Not covered by the appliance warranty) Disconnect the appliance from the electricity supply, remove the oven door (as described previously) as well as the oven shelves. Remove the protective glass light-cover by twisting anti-clockwise. Unscrew the old bulb and discard safely, replace with the type specified in the Technical Data and refit the cover. -
Page 15: Technical Data
VEO9002 Height – 480mm Width – 898mm Depth – 563mm ELECTRICAL DETAILS 240V~ 50Hz Rated Voltage: Max Rated Inputs: VEO9002 : 2600 W 3x 2.5mm ² type H05 RR-F <HAR> Mains supply lead: Oven Light Bulb: 25W/300°C Screw type pygmy... - Page 19 Cod. 12300065120...
Need help?
Do you have a question about the VEO9002 and is the answer not in the manual?
Questions and answers