Related Manuals for Infineon Technologies XE166
Summary of Contents for Infineon Technologies XE166
- Page 1 X E 1 6 6 F a m i l y Ha rd w ar e M a nu al XE 16 6 E asy K it B oa rd Ve rsi on 3. 1 H a r d w a r e M a n u a l V 1 .
- Page 2 Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life.
- Page 3 Hardware Manual XE166 Easy Kit Board Version 3.1 Device1 Revision History: V1.2 2009-08 Previous Version(s): 1.1 change device name to series Trademarks ® TriCore is a trademark of Infineon Technologies AG. We Listen to Your Comments Is there any information in this document that you feel is wrong, unclear or missing? Your feedback will help us to continuously improve the quality of this document.
-
Page 4: Table Of Contents
General Information about XE166 Easy Kit Board ........ -
Page 5: Introduction - Xe166 Family
XE166 core. Together, the Microcontroller's real-time capability and ease of use and the DSP's mathematical performance and data throughput form a powerful singe-chip solution ideal for many embedded applications. For detailed technical information about the different derivatives please refer to the XE166 family web pages on the Infineon Internet. -
Page 6: General Information About Xe166 Easy Kit Board
– On board USB to JTAG / UART interface – Powered via USB Connectors – The XE166 Board offers a wide variety of connectors: – USB connector for ASC/JTAG Interface – 4 pin header for LIN Transceiver – 16-pin header for JTAG interface (OCDS) –... -
Page 7: Block Diagram
Hardware Manual XE166 Easy Kit Board Version 3.1 General Information about XE166 Easy Kit Board Block Diagram Voltage Regulator CAN Transceiver LIN Transceiver EEPROM XE166 8 LEDs USB To UART/ JTAG Bridge XTAL Figure 1 Block diagram of XE166 Easy Kit layout overview Board Overview P10.0... -
Page 8: Dip Switch S102
These configurations are accomplished by latching the logic levels at a number of pins at the end of the internal reset sequence. DIP switch S102 allows to configure the startup setting of the XE166 during RESET. The default System Startup Configuration is shown in Table 1. -
Page 9: Basic Startup Configuration For Xe167F And Xe164F
Hardware Manual XE166 Easy Kit Board Version 3.1 General Information about XE166 Easy Kit Board 2.4.1 Basic Startup Configuration for XE167F and XE164F Table 2 Basic Startup Configuration via External Circuitry Startup Mode CFG pins P10 CFG pins P10 [2] CFG pins P10 [1] CFG pins P10 [0]... -
Page 10: Usb Driver Installation
Hardware Manual XE166 Easy Kit Board Version 3.1 General Information about XE166 Easy Kit Board USB Driver installation All USB-Transaction are realized by the USB-Software running on a Host-Computer. The USB-Device driver is communicating with the Equipment connected to the Computer. -
Page 11: Easy Kit Power Supply Concept
Hardware Manual XE166 Easy Kit Board Version 3.1 General Information about XE166 Easy Kit Board Easy Kit Power Supply concept The Easy Kit USB Power Supply concept enables the user to work with the Kit without an external Power Supply. -
Page 12: Power Supply Via Power Plug
Power Supply via Power Plug The XE166 Board can be supplied either with USB cable or with an external power supply. For external power supply a regulated DC power supply with max. 12Volt/ 400mA can be connected to the power connector. The maximum power dissipation of the used voltage regulator has to be taken into account. -
Page 13: Information In Detail
Information in Detail Information in Detail The XE166 family supports variety of start-up modes, allowing the user to make selections in three aspects: • Main functionality - where from the user code will be started (on-chip Flash, PSRAM, external memory);... -
Page 14: Dip Switch Setting Xe166
Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail 3.1.2 DIP Switch Setting XE166 Table 7 DIP Switch Settings for S102 Name in Default configuration Description schematic S102 Startup configuration: Standard start from internal Flash xx-xx-xx-xx-OFF S102 Startup configuration:... -
Page 15: Can1/2 (X110, X111)
CAN1/2 (X110, X111) On the board are two CAN transceiver connected to the MultiCAN on XE166 node 0 and 1. The transceivers are connected to two IDC10 plug. For the pinout of IDC10 plug see Figure 7. You can use a IDC female connector with crimp connector, flat cable and SUB-D 9 plug with crimp connector to have a 1:1 adapter to SUB-D 9. -
Page 16: Dap Interface
Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail CPUCLK /BRK_OUT /TRST TCLK / OCDS_E / BRK_IN Figure 9 On-board header X202 3.2.5 DAP Interface The board comes with a DAP connector (X204). For pinout of this connector see Figure 10. You can connect a DAP hardware here. -
Page 17: Leds
Serial EEPROM By default the USIC0 Channel1 of the XE166 is connected to a serial EEPROM with a size of 128K (16.384 x 8). If the SSC bootstrap loader is needed the four resistors have been reconfigured as described in table 8. -
Page 18: Pin Definition And Location
Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail Pin Definition and Location 3.3.1 XE167 - 144 - Pinout Figure 11 Pinout of the144 Pin device Note: For the XE167F Series Pin P2.13 is used as Tref pin. - Page 19 Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail X107 P0.7 P10.6 P10.5 P3.3 P2.10 VDDI1 P3.1 P3.0 P2.9 P0.1 P4.5 P3.7 P3.6 P3.5 P10.4 P10.3 TREF P10.2 P10.1 P0.2 P2.8 P4.6 VDDPB VDDPB P10.7 P0.6 P3.4 P0.5 P3.2...
-
Page 20: Xe164 - 100 - Pinout
Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail 3.3.2 XE164 - 100 - Pinout Figure 13 Pinout of the 100 pin device For the XE164F Series Pin P2.13 is used as Tref pin. Hardware Manual V1.2, 2009-08... - Page 21 Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail X107 P0.7 P10.6 P10.5 P2.10 VDDI1 P2.9 P0.1 P10.4 P10.3 TREF P10.2 P10.1 P0.2 P2.8 VDDPB VDDPB P10.7 P0.6 P0.5 P0.4 P0.3 P10.0 P2.7 P0.0 P1.0 P4.3 VDDPB VDDPB P10.8...
-
Page 22: Xe162Fm - 64 - Pinout
Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail 3.3.3 XE162FM - 64 - Pinout Figure 15 Pinout of the 64 pin device Zero Ohm Resistors For configuration purposes several zero ohm resistors have been implemented. The functionality of these resistors are shown in the table below. - Page 23 Hardware Manual XE166 Easy Kit Board Version 3.1 Information in Detail Table 10 Zero Ohm Resistors Component Name in Description schematic Microcontroller XE166 Analog reference R220 / R221 change of analog reference source R219 Voltage supply R212 / R229 change of voltage supply...
-
Page 24: Getting Started
Hardware Manual XE166 Easy Kit Board Version 3.1 Getting Started Getting Started For the successful start up of the XE166 Easy Kit, the following items should be done: Figure 16 XE166 Easy Kit (144-Pin) By default a HELLO WORLD program can be executed. The following steps are needed to be successful. -
Page 25: Power Supply
OCDS Debugging Interface The XE166 Easy Kit offers two types of JTAG interfaces. With the FTDI chip an on board USB JTAG wiggler has been implemented. Further the USB interface allows to emulate a USB to UART bridge. Both can be done at the same time. -
Page 26: Schematic
Hardware Manual XE166 Easy Kit Board Version 3.1 Schematic Schematic Hardware Manual V1.2, 2009-08... - Page 27 Hardware Manual XE166 Easy Kit Board Version 3.1 Schematic Hardware Manual V1.2, 2009-08...
- Page 28 . i n f i n e o n . c o m Published by Infineon Technologies AG...
Need help?
Do you have a question about the XE166 and is the answer not in the manual?
Questions and answers