Yamaha DX9 Operating Manual page 35

3.
HOW
TO
PLAY
PRE-PROGRAMMED
VOICES
•
Playing the
Internal
Voices
The
DX9
has
20
internal
voices
,
any one
of
which
ca n be
selected
simply by
pressing
the
IMEMORY
SELECTl
key,
and
then by
pressing
the appropriate Voice Select key.
Each Voice
Select
key
has a large
numeral
that corresponds
to the voice
number
at
its
left
edge.
Select
and
play
each voice to
get
a feel
for the kind of
sounds
that
are available.
Press
the
Memory
Select key,
set
to
the Play
mode.
EDIT/
COMPARE
MEMORY
SELECT
^\rA
\^-
Select the
preset voice
ice
V-^
20
-\
voice
number
•
Playing the External Voices
The
voice data contained
on
the voice data
cassette
must
be
loaded into the instrument before
it
can be
played.
Two
types of
LOAD
functions
are
provided:
LOAD,
with
which
an
entire
group of
20
voices
is
loaded,
and
LOAD
SINGLE,
with
which any
desired single voice
can be
loaded.
1)
LOADing
an
entire
20-voice group.
(1)
Make
sure the
cassette
recorder
is
properly connect-
ed to the
DX9,
insert
the
cassette
containing the
desired
voice group, and
set
the tape
to
the beginning of
that
voice
group
{disengage the
remote
control function to
do
this).
Stop
the
cassette recorder.
(2)
Turn
MEMORY
PROTECT
OFF.
FUNCTION CONTROL
MEM.
PROTECT: OFF
(3)
Press
the
I
LOAD
I
key and then
the
|
YES|
key and
the
display will read
"from
TAPE
to
MEM
all
ready?"
(the
remote control function
is
re-engaged).
(4)
Make
sure
the
cassette recorder's
headphone
jack
is
connected to the
DX9
and
press
the
cassette
recorder
PLAY
button^
(5)
Press
the
I
YES
|
key and
the
"ready?"
portion of the
display
will
disappear, the tape
will
begin to run,
and
the
pilot
tone
will
be
heard.
(6)
Adjust the
cassette
recorder
volume
control to
set
the
pilot
tone
at a
comfortable
listening level.
(7)
When
the data
signal
begins the
bottom
right
hand
corner of the display
will
read
"1"
through
"20"
as
the
corresponding
voices are loaded
into
the
internal
memory.
fror^ TAPE to MEM
all
1
Display
will
read
""1"
through
"20"
(8)
When
the
LOAD
operation
is
completed the
DX9
PLAY
mode
will
be engaged and the
cassette
recorder
will stop.
*
Using
a
Cassette
Recorder with
No
REMOTE
Terminal
The
SAVE
and
LOAD
procedures
are basically
same
for
cassette recorders with or without
a
REMOTE
terminal.
When
there
Is
no
REMOTE
terminal, the cassette recorder
must
ma
nually be
set
to the record or play
mode
after
the
and
I
YES
I
keys have been
pressed
SAVE
or
LOAD
("ready?"
display).
2)
LOADing
a
single voice.
This function
loads
any
single voice
from
within
a
voice
group, and operates
basically
in
the same
way
as for
loading
a voice
group.
Instead of pressing the
[LOAD
key,
press
the
[LOAD SINGLE]
key.
(1)
Make
sure
the
cassette recorder
is
properly connect-
ed
and
set
the tape to the beginning of the
voice
group
that
contains the desired
voice.
(2)
Press
the
[LOAD
SINGLE]
key and then
the
[YES]
key and
the
display
will
read
"from
TAPE
to
BUF
single?
(1—20)". The
DX9
is
asking
you
for the
number
of the desired
voice.
(3)
Press
the
preset
key corresponding
to the
number
of
the desired voice and the display
will
respond with
the
chosen
voice
number and
"ready?".
Pressing
fron TAPE
single
18
to
BUF
ready?
voice
number
(4)
Press the
|
YES
|
key and
the tape
will
begin playback.
The
pilot
tone
will
be
heard.
(5)
Set the
cassette recorder
volume
control so that the
pilot
tone
is
at a
comfortable
listening
level.
(6)
The
display counts
down
the voices
in
the group, and
the
DX9 PLAY
mode
is
engaged
when
the desired voice
has
been
loaded.
The
voice
number
display
shows
"0".
The
loaded voice must then be
stored
in
any
preset
number
according to the
STORE
instructions
in
your
owner's manual.
.YAMAHA
IOMD-73AI
83113
%
Printed
in
Japan