Yamaha DX9 Operating Manual page 20

4)
Adjust the
cassette
recorder
volume
control so that
the
pilot
tone
is
at a
comfortable
listening
level.
5)
When
the data signal
begins
{a
discontinuous tone)
the
bottom
right
hand corner of the display should
read
"1"
through
"20"
as
each voice
is
verified.
When
verification
is
complete the display
will
read
"OK"
followed by
"VERIFY COMPLETED".
UERIF'-
TfiPE
1
-Display
will
read
"1"
through
"20"
UERIF
OK
I.) TAPE
20
Display
shows
indicats
"OK!",
The
VERIFY
operation can be carried
out
directly
(not necessarily
immediately following a
SAVE
opera-
tion}
by
using
the
1
SAVE/VERIFY
|
key
to
set
the
display to
"VERIFY TAPE?"
in
the
FUNCTION
mode.
•
REMOTE
Normally when
the
cassette recorder's
remote
termi-
nal
is
connected
to the
DX9
with the
FUNCTION
CONTROL
TAPE
REMOTE
OFF,
the tape
will
not
run
until either the
LOAD
or
SAVE
function
Is
initi-
ated even
if
the Play or
Record
controls are engaged.
The
REMOTE
function
makes
it
possible to start or
stop the tape to
facilitate locating
the beginning of
voice groups,
etc.
1}
Press
the
[REMOTE]
key.
10
REMO
FUNCTION CONTROL
TAPE REMOTE
:
OFF
2} Press
the
I
ON
|
key.
FUNCTION CONTROL
TRPE REMOTE
:
ON
YES
This turns
remote control
ON
so the tape recorder
can be run
as
required.
5.
LOAD
Two
types of
LOAD
functions are provided:
LOAD,
with
which an
entire
group
of
20
voices
is
loaded,
and
LOAD
SINGLE,
with
which any
desired single voice
can be
loaded.
1)
LOADing
an
entire
20-voice group.
(1)
Make
sure the cassette
recorder
is
properly con-
nected to the
DX9,
insert the cassette
containing the
desired voice group,
and
set
the tape to
the beginning
of
that
voice group (disengage the
remote control function
to
do
this).
Stop
the cassette recorder.
(2)
Turn
MEMORY
PROTECT
OFF.
FUHCTIOH CONTROL
MEn.
PROTECT: OFF
(3)
Press
the
|
LOAD
|
key and then the
|
YES|
key and
the display
will
read
"from
TAPE
to
MEM
all
ready?
"
(the
remote
control function
is
re-engaged),
(4}
Make
sure the cassette recorder's
headphone
jack
is
connected to the
DX9
and
press
the
cassette
recorder
PLAY
button.
(5)
Press
the
|
YES
|
key and the "ready?" portion
of
the
display will
disappear, the tape
will
begin to run,
and
the
pilot
tone
will
be heard.
(6)
Adjust the cassette
recorder
volume
control to
set
the pilot
tone
at a
comfortable
listening level.
(7)
When
the data signal
begins the
bottom
right
hand
corner of the display will
read
"1"
through
"20"
as the
corresponding voices are
loaded
into
the
internal
memory.
frori TOPE to MEM
all
1
Display
will
read
""1"
through
"20"
(8)
When
the
LOAD
operation
is
completed
the
DX9
PLAY
mode
will
be engaged
and
the
cassette
recorder
will stop.
•
Using
a Cassette
Recorder with
No
REMOTE
Terminal
The
SAVE
and
LOAD
procedures are basically
same
for
cassette
recorders with or
without
a
REMOTE
terminal.
When
there
is
no
REMOTE
terminal, the cassette recorder
must manually be
set
to
the record or piay
mode
after the
I
SAVE
I
or
I
LOAD
\
and
|
YES
|
keys have been pressed
("ready?"
display}.
^^
^^.
<I9>