Yamaha DX9 Operating Manual page 23

Using MIDI.
•
Real-Time Control
1.
Sequencer
Controlled Automatic Performance
With the system
shown
in
figure
1, let
us use the
DX9
as
synthesizer
A,
and
the
DX7
as synthesizer
B.
Specify
the
DX9
receiving channel
as
1,
and
the
DX7
receiving
channel
as
2.
This
will
enable automatic performance
under sequencer
control.
2.
Remote
Control
Performance
Hooking up
the remote keyboard KX1
to a
DX9
as
shown
in
the
figure, will
enable you
to remotely
control the
DX9
from
the
KX1
keyboard.
In
addition, by connecting
a
DX9
and
a
DX7,
the
DX7
can be controlled
from
the
DX9
keyboard.
The DX9's
send channel
number
should
also
be
specified as
1
'
OUT
KX1
(DX9)
IN
DX9
(DX7)
• Transmit
System
Information
1.
Transmit
Single
Voice Data
When
the
display appears
as
shown
in
the
figure, press
the voice
number
key
for
the voice you
wish
to transmit,
The
corresponding
voice data
will
be output from MIDI
OUT.
FUNCTION CONTROL
SVS INFO
flUPlIL
in this condition
SELECT
1
^
20
n
the voice you
wish
to transmit.
2.
Transmit Voice Data
for All
20
Voices
Press
[e
when
the display appears
as
shown
in
the
upper
area of the
figure.
The
display
will
change
to that
shown
in
lower
area of the
figure. Pressing
[pfsj
|
will
cause the voice data
for
all
20
voices to be output from
MIDI OUT.
FUNCTION CONTROL
SVS
INFO
flUfllL
in this
condition
Pressing the
the display
will
change
to
FUNCTION CONTROL
MIDI TRhNSMIT?
key, the voice data
for
all
20
voices
to
be output from
ch.1
3.
Transmit Voice
or
FUNCTION
Parameters
^^^^
^^^e dis pla
y
reads
"SYS INFO AVAIL",
press
s'^^er
i
EDIT
I
or
|
FUNCTIONI
Pressing the key
cor-
responding to the parameter
that
you
wish to transmit
will
output the data
for that parameter
from MIDI OUT.
FUNCTION CONTROL
SVS INFO
flUfllL
in this
condition
Press either
EDIT/
COMPARE
FUNCTfON
^-E
Press the voice
number
key for the voice or
function parameters you
wish
to transmit.
key.
Note; For
all
of the above, the transmit channel
number
Of the
DX9
is 1.
•
Receiving
System
Information
Select the
same number
for both the
receive
and
the
trans-
mit
channels.
When
the
display reads
"SYS INFO
AVAI L",
the instrument
will
be ready
to receive system
information.
1.
Receiving
Single
Voice Data
After
receiving the voice data
for a single voice, the voice
data
will
be held
in
the
memory
of the buffer and
the
voice
number
display shows
"0".
2.
Receiving the Voice Data
for
all
20 Voices
Switching the
PROTECT
off for the
memory,
will
cause the voice
data for
all
20
voices to
be memorized
into
the
internal
memory.
3.
Receiving
Voice
or
FUNCTION
Parameters
When
receiving
this
Information, the
unit
will
vary the
data
for that particular parameter.
<22>