Advertisement

SERVICE MANUAL
Ver 1.3 2002.03
AUDIO
POWER SPECIFICATIONS
(US model only)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION
With 4-ohm loads, both channels driven from
100 - 10,000 Hz; rated 1.5 W per channel-
minimum RMS power, with no more than 10 %
total harmonic distortion in AC operation.
Other Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about
200 mm from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +0/–1 dB
Wow and flutter
Below measurable limit
Radio
section
US, Canadian, *E92, Taiwan, Mexican models
Frequency range
FM: 87.6 - 108 MHz
AM: 530 - 1 710 kHz
Antennas
FM: Telescopic antenna
AM: Built-in
ferrite bar antenna
Singapore, Korean, Argentina models
Frequency range
FM: 87.6 – 107 MHz (Korean model)
87.5 – 108 MHz (Singapore, Argentina models)
AM:
531 – 1,602 kHz (9 kHz step)
530 – 1,610 kHz (10 kHz step)
Sony Corporation
9-873-110-14
2002C0500-1
Personal Audio Company
C 2002.03
Published by Sony Engineering Corporation
Model Name Using Similar Mechanism
CD
CD Mechanism Type
Section
Optical Pick-up Name
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type

SPECIFICATIONS

IF
FM: 10.7 MHz
AM: 450 kHz
Aerials
FM: Telescopic aerial
AM: Built-in ferrite bar aerial
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 sec. with Sony cassette C-60
Frequency response
TYPE I (normal): 70 - 13 000 Hz
General
Speaker
Full range: 8 cm (3
1
in.) dia.,
4
4 Ω, cone type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 64 Ω impedance headphones
Power output
2 W + 2 W (at 4 Ω, 10 % harmonic distortion
in AC operation)
Power
requirements
For CD radio cassette-corder:
US, Canadian, *E92, Taiwan, Mexican models
120
V AC, 60 Hz
Argentina model
220-230 V AC, 50Hz
Korean model
220 V AC, 60Hz
Singapore model
230 V AC, 50 Hz
9 V DC, 6 size C (R14) batteries
For memory back-up:
4.5 V DC, 3 size AA (R6) batteries
For remote control:
3 V DC, 2 size AA (R6) batteries
CD RADIO CASSETTE-CORDER
CFD-E75
US Model
Canadian Model
E Model
CFD-926L
KSM-213CDP
KSS-213C
CFD-926L
MF-V5-117
Power consumption
AC 14 W
Battery life
For CD radio cassette-corder:
FM recording
Sony R14P: approx. 5 h
Sony alkaline LR14: approx. 20.5 h
Tape playback
Sony R14P: approx. 6 h
Sony alkaline LR14: approx. 27 h
CD playback
Sony R14P: approx. 1.5 h
Sony alkaline LR14: approx. 8 h
Dimensions
Approx. 283 × 165 × 281 mm (w/h/d)
1
1
1
(11
× 6
× 11
inches) (incl. projecting parts)
4
2
8
Mass
Approx. 3.5 kg (7 lb. 11 oz) (incl. batteries)
Supplied accessories
AC power cord (1)
Remote control (1)
*E92: Central and South America model
Design and specifications are subject to change without
notice.

Advertisement

Table of Contents
loading

Summary of Contents for Sony CFD-E75

  • Page 1: Specifications

    4-track 2 channel stereo Fast winding time Sony R14P: approx. 6 h Other Specifications Approx. 120 sec. with Sony cassette C-60 Sony alkaline LR14: approx. 27 h CD player section Frequency response TYPE I (normal): 70 - 13 000 Hz...
  • Page 2 OPERATION. REPLACE THESE COMPONENTS WITH DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS POSANTS QUE PAR DES PIÈCES SONY DONT LES SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- NUMÉROS SONT DONNÉS DANS CE MANUEL OU LISHED BY SONY.
  • Page 3: Table Of Contents

    CFD-E75 SECTION 1 SERVICING NOTES TABLE OF CONTENTS NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT SERVICING NOTES ..........The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated GENERAL ..............
  • Page 4 CFD-E75 Ver 1.3 CHUCK PLATE JIG ON REPAIRING On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. • Code number of Chuck Plate Jig: X-4918-255-1 MODEL IDENTIFICATION  C F D - E 7 5 MODEL NO.
  • Page 5: General

    CFD-E75 SECTION 2 This section is extracted from instruction manual. GENERAL Basic Operations Playing a CD Use these buttons for additional operations 1, 2 Jog dial ZPUSH OPEN/CLOSE VOLUME +, — POWER Do this adjust the volume Press VOLUME +, — (VOL +, — on the remote).
  • Page 6: Playing A Tape

    CFD-E75 Playing a tape Use these buttons for additional operations POWER VOLUME +, — m, M Press adjust the volume VOLUME +, — (VOL +, — on the remote) stop playback Connect the supplied AC power cord (see page 24).
  • Page 7: Setting The Clock

    CFD-E75 The Timer Setting the clock Press DSPL¥ENT MEM. The clock starts from 00 seconds. — —:— — indication appears in the display until you set the clock. The time display system: 12-hour system MENU DSPL AM 12:00 = midnight...
  • Page 8: Disassembly

    CFD-E75 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Cabinet lower assy AC INLET board, POWER board TUNER board, MAIN board Cover plate assy CD mechanism deck Optical pick-up (KSM-213CDP) (KSS-213C)
  • Page 9: Ac Inlet Board, Power Board

    CFD-E75 3-3. AC INLET BOARD, POWER BOARD 5 two screws 2 two screws (BVTP3 × 10) (BVTP3 × 10) 3 AC INLET board 1 connector (CN902) 4 connector (CNP901) 6 plate shield (TRANS) 7 POWER board 3-4. TUNER BOARD, MAIN BOARD 4 two screws (BVTP3 ×...
  • Page 10: Cover Plate Assy

    CFD-E75 3-5. COVER PLATE ASSY 3 FFC cable 27P 4 wire (flat type) (14 core) (CNP801) (CNP323) 5 FFC cable 13P 6 screw (BVTP3 × 10) (CNP322) 2 connector (CNP802) 6 two screws (BVTP3 × 10) 6 screw (BVTP3 × 10)
  • Page 11: Optical Pick-Up (Kss-213C)

    CFD-E75 3-7. OPTICAL PICK-UP (KSS-213C) 2 two claws 3 cover, CD 9 optical pick-up (KSS-213C) 1 two claws 5 gear (A) 4 claw 6 claw 8 sled shaft 3-8. CABINET FRONT ASSY 4 Push the knob (stop/eject). 8 cabinet front assy 6 screw (BTP2.6 ×...
  • Page 12: Tape Mechanism Deck (Mf-V5-117)

    CFD-E75 3-9. TAPE MECHANISM DECK (MF-V5-117) 2 tape mechanism deck (MF-V5-117) 1 four screws (BVTP3 × 10) 3-10. CD LID 4 CD lid 3 boss 1 screw (BTP2.6 × 8) 2 damper CD lid driver...
  • Page 13: Lid Cassette Assy, Lcd Board

    CFD-E75 3-11. LID CASSETTE ASSY, LCD BOARD 1 two screws 4 LCD board (BTP2.6 × 8) 3 lid cassette assy 2 two claws 3-12. HEAD (HRP301), MOTOR ASSY (M301), BELT 3 Remove four solders. 6 two screws (B2.6 × 5)
  • Page 14: Connector Setting

    CFD-E75 3-13. CONNECTOR SETTING Note: When connecting leads, set it as shown in the figure. CNP801 TC board CN321 CN303 CNP802 CNP322 MAIN board TUNER board CN322 CNP1 CNP321...
  • Page 15: Mechanical Adjustments

    CFD-E75 SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS PRECAUTION PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened 1. Setting swab : MEGA BASS control : OFF record/playback head pinch roller erase head rubber belts TAPE DECK SECTION 0 dB=0.775 V...
  • Page 16: Tuner Section

    CFD-E75 0 dB=1 µV AM IF ADJUSTMENT TUNER SECTION Adjust for a maximum reading on level meter [AM] 450 kHz Setting: Function : RADIO AM VCO VOLTAGE ADJUSTMENT RADIO BAND button : AM Adjustment Part Frequency Display Reading on Digital Voltmeter 530 kHz 1.0 ±...
  • Page 17 CFD-E75 Adjustment Location: – TUNER BOARD (Component Side) – T2 FM IF Adjustment AM VCO Voltage Adjustment T1 AM IF Adjustment FM VCO Voltage Adjustment FM Tracking Adjustment AM Tracking Adjustment – TUNER BOARD (Conductor Side) – (ANT) (VT) (GND) –...
  • Page 18: Cd Section

    CFD-E75 CD SECTION CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias. Focus Bias Check 1. Connect the oscilloscope to TP (RF) and TP (GND) on the CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3.
  • Page 19: Diagrams

    CFD-E75 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – CD Section – CD BOARD MAIN BOARD RF AMP, FOCUS/TRACKING SERVO, DIGITAL SIGNAL PROCESSOR, (1/4) CNP701 CLV SERVO, D/A CONVERTER FIN2 IC701 CNP702 CNP323 DETECTOR INTERPOLATION ERROR LCHO CD L-OUT MUTE SLISE LEVEL...
  • Page 20: Block Diagram - Tuner Section

    CFD-E75 6-2. BLOCK DIAGRAM – TUNER Section – TUNER BOARD MAIN BOARD FM IFT (2/4) FM IF ANT1 FM TELESCOPIC ANTENNA FM/AM RF AMP, MIX, OSC, FM/AM IF AMP, DET, MPX CN321 CNP322 CNP1 (1/2) (2/4) FM/AM FM RF LOUT...
  • Page 21: Block Diagram - Main Section

    CFD-E75 6-3. BLOCK DIAGRAM – MAIN Section – TC BOARD MAIN BOARD (3/4) POWER BOARD (1/2) TC POWER CN303 (1/3) D394 REC/PB EQ AMP CD IN L IC301 VREF FROM CD SECTION POWER (Page 19) MIC IN MUTE IC390 L.CD...
  • Page 22: Block Diagram - Power Supply Section

    CFD-E75 6-4. BLOCK DIAGRAM – POWER SUPPLY Section – MAIN BOARD (4/4) LCD BOARD CNP801 ı ı LIQUID CRYSTAL DISPLAY LCD801 ı ı REMOTE AAAA CONTROL BBBB RECEIVER CCCC DDDD IC804 CNP811 SYSTEM CONTROLLER POWER BOARD (2/2) IC801 CN322 (3/3)
  • Page 23 CFD-E75 • Waveforms • Circuit Boards Location – CD Board – – TUNER Board – – MAIN Board – 1 IC701 4 (RF) (CD Play mode) 5 IC2 w; (XOUT) 7 IC801 es (XTAL) 500 mV/DIV, 1 µs/DIV 500 mV/DIV, 5 µs/DIV...
  • Page 24: Printed Wiring Board - Cd Section

    CFD-E75 6-5. PRINTED WIRING BOARD – CD Section – • See page 23 for Circuit Boards Location. • Semiconductor Location Ref. No. Location CD BOARD IC701 IC702 Q701 IC701 MAIN BOARD (GND) CNP323 (Page 29) (RF) OPTICAL PICK-UP BLOCK (KSS-213C) Note on Printed Wiring Board: •...
  • Page 25: Schematic Diagram - Cd Section

    CFD-E75 6-6. SCHEMATIC DIAGRAM – CD Section – • See page 23 for Waveforms. • See page 36 for IC Block Diagrams. C729 S701 (LIMIT) C747 R724 C730 C744 R731 2.2k R728 C746 CNP702 R727 C745 2.2k R730 R729 P-GND CD MOTOR 6.0V...
  • Page 26: Printed Wiring Board - Tuner Section

    CFD-E75 Ver 1.1 6-7. PRINTED WIRING BOARD – TUNER Section – • See page 23 for Circuit Boards Location. ANT1 FM TELESCOPIC TUNER BOARD ANNTENA (VT) (ANT) (US, CND, E92, MX) (GND) (SP, TW, KR, AR) MAIN BOARD CN321 (Page 29)
  • Page 27: Schematic Diagram - Tuner Section

    CFD-E75 Ver 1.1 6-8. SCHEMATIC DIAGRAM – TUNER Section – • • See page 23 for Waveform. See page 36 for IC Block Diagrams. AM FERRITE-ROD ANTENNA 220p (VT) 100p AM OSC KV1520NT 0.22 1000p JC12 JC11 0.01 220k 100p 0.01...
  • Page 28: Printed Wiring Board - Tape Deck Section

    CFD-E75 6-9. PRINTED WIRING BOARD – TAPE DECK Section – 6-10. SCHEMATIC DIAGRAM – TAPE DECK Section – • See page 23 for Circuit Boards Location. • See page 23 for Waveform. • See page 37 for IC Block Diagram.
  • Page 29: Printed Wiring Boards - Main/Lcd Boards

    CFD-E75 Ver 1.1 6-11. PRINTED WIRING BOARDS – MAIN/LCD Boards – • See page 23 for Circuit Boards Location. MAIN BOARD S304 (Page 28) (TAPE PLAY) M301 D320 (CAPSTAN/REEL) JW320 TC BOARD CN303 C120 R123 JW316 JW318 S303 R130 R224...
  • Page 30: Schematic Diagram - Main Board (1/2)

    CFD-E75 6-12. SCHEMATIC DIAGRAM – MAIN Board (1/2) – (1/2) C320 R123 C120 C124 R320 0.0022 C321 R124 C123 R325 0.01 6.8k R120 R121 220k Q122 Q120 DTC343TKA-T146 KTC3198GR-AT AF AMP C324 R321 C326 R122 Q122,222 C331 MUTING R222 ELECTRICAL...
  • Page 31: Schematic Diagram - Main (2/2)/Lcd Boards

    CFD-E75 Ver 1.1 6-13. SCHEMATIC DIAGRAM – MAIN (2/2)/LCD Boards – • See page 23 for Waveforms. IC804 SPS-442E LCD801 LIQUID CRYSTAL DISPLAY REMOTE CONTROL RECEIVER CNP811 CNP801 (2/2) R838 R837 100k RESET SIGNAL GENERATOR IC803 PST9128-T R836 100k R835...
  • Page 32: Printed Wiring Boards - Panel Section

    CFD-E75 6-14. PRINTED WIRING BOARDS – PANEL Section – • See page 23 for Circuit Boards Location. KEY VOLUME BOARD JOG BOARD KEY POWER BOARD R422 DSPL MODE MENU ENT MEM ALARM JW401 MAIN BOARD CNP802 (Page 29) S403 1-681-672-...
  • Page 33: Schematic Diagram - Panel Section

    CFD-E75 6-15. SCHEMATIC DIAGRAM – PANEL Section – RE401 ROTARY ENCODER (JOG DIAL) S407 MENU ALARM S406 CNP401 CN404 DSPL ENT MEM JOG-A JOG-B KEY1 KEY2 CN403 CN401 JOG-A JOG-B R408 CNP402 1.5k KEY2 KEY2 KEY1 S408 CN402 APPROBATE S401...
  • Page 34: Printed Wiring Boards - Power Supply Section

    CFD-E75 6-16. PRINTED WIRING BOARDS – POWER SUPPLY Section – • See page 23 for Circuit Boards Location. (L-CH) BACK-UP BOARD BATY B BOARD POWER BOARD (R-CH) 1-681-678- (13) 1-681-677- (13) DRY BATTERY SIZE “D” (IEC DESIGNATION) 6PCS. 9V DRY BATTERY SIZE “AA”...
  • Page 35: Schematic Diagram - Power Supply Section

    CFD-E75 Ver 1.1 6-17. SCHEMATIC DIAGRAM – POWER SUPPLY Section – POWER AMP IC390 BA5417 CNP392 (L-CH) (R-CH) C193 C293 C195 R397 R193 R293 2200 2.2k 3.3k 3.3k J301 C296 C398 R194 L190 0.22 1µH C194 C294 R294 L290 C295 D390 0.022...
  • Page 36 CFD-E75 • IC Block Diagrams – CD Board – IC702 BA6998FP-E2 IC701 LC78645NE 78 77 76 75 74 73 72 71 70 69 68 65 64 63 62 61 DRIVE DRIVE BUFFER BUFFER PLL VCEC COMMAND INTERFACE LEVEL LEVEL CLV, CAV...
  • Page 37 CFD-E75 IC2 LC72137M-TLM XOUT REFERENCE DIVIDER AOUT PHASE 12BITS DETECTOR PROGRAMMABLE CHARGE DIVIDER PUMP UNLOCK DETECTOR POWER ON RESET SWALLOW COUNTER FMIN 1/16,1/17 4BITS UNIVERSAL COUNTER AMIN IFIN – TC Board – IC301 TA2068N LINE LINE OUT1 AMP1 BUF AMP...
  • Page 38: Ic Pin Function Description

    CFD-E75 Ver 1.1 6-18. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC801 CXP83624-035Q (SYSTEM CONTROLLER) Pin No. Pin Name Description CD-WRQ Interruption detection signal input from the LC78645NE (IC701) Sircs remote control signal input from the remote control receiver (IC804)
  • Page 39 CFD-E75 Pin No. Pin Name Description Tape function control signal output to the TA2068N (IC301) TAPE “L”: radio or CD on, “H”: tape on TU-DATA PLL serial data output to the FM/AM PLL (IC2) TU-CLK PLL serial data transfer clock signal output to the FM/AM PLL (IC2) TU-MUTE Tuner muting on/off control signal output to the FM/AM PLL (IC2) “H”: muting on...
  • Page 40: Exploded Views

    CFD-E75 Ver 1.3 SECTION 7 EXPLODED VIEWS NOTE: The components identified by • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
  • Page 41: Cabinet Upper Section

    CFD-E75 Ver 1.3 7-2. CABINET UPPER SECTION S901 supplied optical pick-up supplied section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 51 A-3062-355-A MAIN BOARD, COMPLETE (US, CND, E92, MX) 3-241-089-71 CABINET UPPER (RED: PSYC TYPE) (CND)
  • Page 42: Cabinet Front Section

    CFD-E75 Ver 1.3 7-3. CABINET FRONT SECTION LCD801 tape deck section (MF-V5-117) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-757-967-11 FFC CABLE 27P 3-229-991-11 LID CASSETTE (YELLOW: ORIGINAL TYPE) 3-229-989-01 HOLDER LCD 3-229-991-21 LID CASSETTE (RED: ORIGINAL TYPE)
  • Page 43: Cabinet Lower Section

    CFD-E75 Ver 1.3 7-4. CABINET LOWER SECTION ANT1 T901 supplied not supplied not supplied not supplied not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
  • Page 44: Optical Pick-Up Section (Ksm-213Cdp)

    CFD-E75 7-5. OPTICAL PICK-UP SECTION (KSM-213CDP) not supplied not supplied not supplied (M701) M702 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No.
  • Page 45: Tape Mechanism Deck Section-1 (Mf-V5-117)

    CFD-E75 7-6. TAPE MECHANISM DECK SECTION-1 (MF-V5-117) HRP301 HE301 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-933-010-01 SPRING (S/P), TORSION * 712 3-008-587-01 SLIDER (STOP) 3-933-025-01 SPRING (P), TORSION * 713 3-008-591-01 SLIDER (PAUSE) 3-040-857-01 LEVER (P)
  • Page 46: Tape Mechanism Deck Section-2 (Mf-V5-117)

    CFD-E75 7-7. TAPE MECHANISM DECK SECTION-2 (MF-V5-117) S304 S303 M301 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-933-029-01 LEVER, ERASING PREVENTION 3-343-358-01 RING, RETAINING 3-933-182-01 SPRING, CASSETTE 3-223-156-01 SPRING (CAM), COMPRESSION 3-932-995-01 GEAR (MID) 3-016-349-01 WASHER...
  • Page 47: Electrical Parts List

    CFD-E75 Ver 1.1 SECTION 8 AC INLET BACK-UP ELECTRICAL PARTS LIST BATY A BATY B NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by parts list may be different from the parts speci- are seldom required for routine service.
  • Page 48 CFD-E75 KEY POWER KEY VOLUME Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > 1-681-672-13 JOG BOARD ********** JC701 1-216-864-11 METAL CHIP 1/16W JC702 1-216-864-11 METAL CHIP 1/16W < ROTARY ENCODER > JC703 1-216-864-11 METAL CHIP...
  • Page 49 CFD-E75 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-681-675-13 LCD BOARD C813 1-162-927-11 CERAMIC CHIP 100PF C818 1-107-826-11 CERAMIC CHIP 0.1uF ********** C819 1-162-927-11 CERAMIC CHIP 100PF 3-229-989-01 HOLDER LCD C820 1-162-927-11 CERAMIC CHIP...
  • Page 50 CFD-E75 Ver 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC803 8-759-645-87 IC PST9128-T R801 1-216-821-11 METAL CHIP 1/16W R802 1-216-821-11 METAL CHIP 1/16W < COIL > R803 1-216-833-11 METAL CHIP 1/16W L321 1-410-509-61 INDUCTOR...
  • Page 51 CFD-E75 Ver 1.1 MAIN OPR/BATT LED POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R860 1-216-841-11 METAL CHIP 1/16W C193 1-126-934-11 ELECT 220uF R861 1-216-841-11 METAL CHIP 1/16W C194 1-164-227-11 CERAMIC CHIP 0.022uF R865 1-216-837-11 METAL CHIP...
  • Page 52 CFD-E75 Ver 1.1 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D906 8-719-988-61 DIODE 1SS355TE-17 D907 8-719-988-61 DIODE 1SS355TE-17 < TRANSFORMER > D908 8-719-056-73 DIODE UDZ-TE-17-2.7B 0 T901 D909 8-719-988-61 DIODE 1SS355TE-17 1-437-319-11 TRANSFORMER, POWER...
  • Page 53 CFD-E75 Ver 1.1 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R201 1-216-835-11 METAL CHIP 1/16W 1-162-964-11 CERAMIC CHIP 0.001uF R202 1-216-807-11 METAL CHIP 1/16W 1-162-970-11 CERAMIC CHIP 0.01uF R203 1-216-843-11 METAL CHIP 1/16W 1-162-970-11 CERAMIC CHIP 0.01uF...
  • Page 54 CFD-E75 Ver 1.1 TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-864-11 METAL CHIP 1/16W < VIBRATOR > 1-216-864-11 METAL CHIP 1/16W 1-216-864-11 METAL CHIP 1/16W 1-760-130-11 VIBRATOR, CRYSTAL (75kHz) 1-216-864-11 METAL CHIP 1/16W (SP, TW, KR, AR)
  • Page 55 CFD-E75 Ver 1.3 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3013-906-A REMOTE CONTROL UNIT (RMT-CE75A/LC) (BLUE: ORIGINAL TYPE) A-3013-907-A REMOTE CONTROL UNIT (RMT-CE75A/LIC) (NAVY BLUE: ORIGINAL TYPE) A-3013-908-A REMOTE CONTROL UNIT (RMT-CE75A/DC) (ORANGE: ORIGINAL TYPE)
  • Page 56: Revision History

    CFD-E75 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.03...

Table of Contents