H3C S5820V2H Configuration Manual page 25

127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
192.168.0.0/24
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32
The output shows that the MCE has a static route for VPN instance vpn1.
# Run OSPF in VPN 2. Create OSPF process 2 and bind it with VPN instance vpn2 on the MCE,
so that the MCE can learn the routes of VPN 2 and add them to the routing table of the VPN
instance vpn2.
[MCE] ospf 2 vpn-instance vpn2
# Advertise subnet 10.214.20.0/24.
[MCE-ospf-2] area 0
[MCE-ospf-2-area-0.0.0.0] network 10.214.20.0 0.0.0.255
[MCE-ospf-2-area-0.0.0.0] quit
[MCE-ospf-2] quit
# On VR 2, assign IP address 10.214.20.2/24 to the interface connected to MCE and
192.168.10.1/24 to the interface connected to VPN 2. (Details not shown.)
# Configure OSPF process 2, and advertise subnets 192.168.10.0/24 and 10.214.20.0/24.
<VR2> system-view
[VR2] ospf 2
[VR2-ospf-2] area 0
[VR2-ospf-2-area-0.0.0.0] network 192.168.10.0 0.0.0.255
[VR2-ospf-2-area-0.0.0.0] network 10.214.20.0 0.0.0.255
[VR2-ospf-2-area-0.0.0.0] quit
[VR2-ospf-2] quit
# On the MCE, display the routing information for VPN instance vpn2.
[MCE] display ip routing-table vpn-instance vpn2
Destinations : 13
Destination/Mask
0.0.0.0/32
10.214.20.0/24
10.214.20.0/32
10.214.20.3/32
10.214.20.255/32
127.0.0.0/8
127.0.0.0/32
127.0.0.1/32
127.255.255.255/32
192.168.10.0/24
224.0.0.0/4
224.0.0.0/24
255.255.255.255/32
Direct 0 0
Direct 0 0
Direct 0 0
Static 60 0
Direct 0 0
Direct 0 0
Direct 0 0
Routes : 13
Proto Pre Cost
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
Direct 0 0
OSPF 10 2
Direct 0 0
Direct 0 0
Direct 0 0
18
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
10.214.10.2 Vlan10
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0
NextHop Interface
127.0.0.1 InLoop0
10.214.20.3 Vlan20
10.214.20.3 Vlan20
127.0.0.1 InLoop0
10.214.20.3 Vlan20
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
127.0.0.1 InLoop0
10.214.20.2 Vlan20
0.0.0.0 NULL0
0.0.0.0 NULL0
127.0.0.1 InLoop0