START-UP GUIDE POWER LINK 100M /COL Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance. For Customer Use: Enter below the Serial No. which is located on the bottom of the body.
CAUTION shock to persons. Changes or modifications not approved by JVC could void user's The exclamation point within an equilateral triangle authority to operate the equipment. is intended to alert the user to the presence of...
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. ATTENTION: (Business users) This symbol is If you wish to dispose of this product, please visit our web page www.jvc-europe.com to obtain information about the take- only valid in the back of the product. European Union.
JPEG file transfer by detection of motion or alarm input. Controlling external devices connected to the serial port VN-E4 comes with 2 serial ports. It is possible to control external devices connected to the serial ports from the clients.
To completely cut off the power, disconnect the power cable About the contents of this manual ● All rights reserved by JVC. Unauthorized duplication or from the wall outlet or remove the power cord from the AC adaptor.
D [FDX/COL] Lamp during transmission of video input at Ch1 to the network. Lights up when VN-E4 is connected to the network via full Turns off when there is no transmission. duplex. The light will not be illuminated in the case of half duplex.
Switch for switching COM1 to servicing. Select CONTROL For connecting the AC adaptor supplied. for normal use. Select SERVICE during maintenance. VN-E4 does not come with a power switch. It starts up automatically upon supply of power using the AC adaptor. S [ALARM OUTPUT] terminal The COM and OUT terminals form the make contact.
Preparation System Connection Example This manual aims at familiarizing users with the fundamental uses of VN-E4 by providing explanations on the monitoring system using the built-in viewer in LAN. Camera 1 VIDEO IN 1 Camera 2 VIDEO IN 2 Camera 3...
When speakers other than the PC’s built-in speaker is used, connect the speaker to the audio output of the PC via the amplifier. AV Devices Connect up to 4 cameras to the 4 video input terminals at the rear panel of VN-E4. Output signals of each camera need not be synchronized.
Mount the side bracket on both left and right (Remove 1 screw from each end of VN-E4. Fasten each end using 1 M3 screw and 2 M4 screws that are supplied with the rack mount bracket.) Fasten to the rack using the M5 screws supplied with the rack mount bracket (2 M5 screws at each end) In case of 2 units.
(1) System configuration for setting the IP address To set a static IP address for VN-E4, connect VN-E4 and PC to a switching hub using straight LAN cables of Category 5 or above. (Do not connect the DHCP server to the switching hub.) Supply power to VN-E4 using the AC adaptor.
(2) IP address setting on PC Set an IP address for the PC that enables communication with VN-E4. Click AStartB. ● Right click AMy Network PlacesB and select APropertiesB. Select the network of the PC that will be used for Web browser operations.
Follow the procedures below to enable the active script if this is disabled in Internet Explorer. ● Go to AToolsB - AInternet OptionsB - ASecurityB and select ATrusted sitesB. Click ASites...B. Uncheck the check box, and add following URL of VN-E4 to the zone. http://192.168.0.2 Click ACustom LevelB.
Launch the Web browser Enter the IP address of the unit. (Factory setting, 192.168.0.2, Click AGoB. is available when there is no DHCP server.) MEMO ● Direct specification of the IP address may not be possible when a proxy server is used for Internet access.
Click the AOKB button when the confirmation screen is displayed. This changes the IP address of VN-E4 to the new setting. Upon changing the IP address for VN-E4, access from this PC may fail. In order to continue access to VN-E4 from the same...
Enter the URL of the image in the address field of Internet Explorer to display the image. For example, to display image on Channel 1 of VN-E4 when the IP address for VN-E4 is 192.168.0.2, enter the following URL in the Internet Explorer address field.
Viewing Using Built-in Viewer Continuous image display, one-shot image recording and bi-directional audio are possible by using the built-in viewer in VN-E4. (1) Setting up Internet Explorer (A pg. 17, 18) (2) Installing the built-in viewer (A pg. 19) (3) Operating the viewer (A pg. 20) (4) Exiting the viewer (A pg.
Follow the procedures below to enable the ActiveX controller and plug-in if these are disabled in Internet Explorer. ● Go to AToolsB - AInternet OptionsB - ASecurityB and click on ATrusted sitesB. Press the ASites...B button and add URL of VN-E4 to the zone.
(2) Installing the built-in viewer Enter the URL of the built-in viewer in Internet Explorer’s address field. For example, enter as follows if the IP address of VN-E4 is 192.168.0.2. https://192.168.0.2/e4viewer/e4monitor.html Enter the URL of built-in viewer of the unit. (In factory setting, https://192.168.0.2/e4viewer/e4monitor.html is the URL when there is no...
AoperatorB in the setup window. Factory setting password is Avn-e4B. Press AOKB button of the setup window, and restart the built-in viewer. Press the ASpeech OnB button to send audio from the PC to VN-E4. Press the button again to stop the audio transmission. The audio transmission feature cannot be used during audio transmission by another client.
Click ACloseB. Launch Internet Explorer and enter the built-in viewer’s URL in the address field again for next launch. For example, enter as follows if the IP address of VN-E4 is 192.168.0.2. https://192.168.0.2/e4viewer/e4monitor.html When a security warning screen appears, click the AOKB button to proceed. Enter the user name and password in the login...
Right-click on the shortcut on the Desktop screen and select Property to display the setting screen. Enter the URL of the built-in viewer in the URL field. For example, enter as follows if the IP address of VN-E4 is 192.168.0.2.
Power/Rated consumption current: 1 Vp-p (75 K) analog composite (x4) AC adaptor AC 100 V to 240 V (20 W) VN-E4E: VN-E4 DC 5 V 3.0 A and below PAL composite video BNC 75 K Ambient temperature 0I to 40I...
Printed in Japan LST0249-001A © 2005 Victor Company of Japan, Limited...