Panasonic DMR-E500H Operating Instructions Manual page 52

Transferring (dubbing) MPEG4/MPEG2
§
MPEG2 data taken on a SD Video Camera
Refer to the control reference on page 51.
After performing steps 1–4 (➡ page 51, right column)
5
Press [3, 4] to select "Create List"
and press [1].
DUBBING
Create dubbing list.
Cancel All
Destination Capacity: 4343MB
1
Dubbing Direction
No. Size
HDD > SD CARD
2
Dubbing Mode
MPEG4 High Speed
3
Create List
Previous
Start Dubbing
ENTER
RETURN
Select the transferring (dubbing) items and register on the list.
1 Press [3, 4] to select "New item" and press [ENTER].
2 Press [3, 4, 2, 1] to select the titles (or play lists)
and press [ENTER].
≥To select a multiple number of items together, press [;]
to add the check mark and press [ENTER] (➡right,
Multiple editing).
≥To show other pages (➡ right)
≥To edit the transferring (dubbing) list (➡right)
≥(Mobile hard disk only) To select the titles in another
folder (➡ page 33)
≥To view the contents of MPEG2 titles. [SD] [PC] (Mobile
hard disk only)
MPEG2 titles are shown as still pictures on the Create list
screen. Follow the steps below to display the chapters.
1. Press [3, 4, 2, 1] to select the title and press
[SUB MENU].
2. Press [3, 4] to select "Chapter View" and press
[ENTER].
Chapter View screen is displayed.
When transferring (dubbing) by converting to MPEG4 format,
the displayed "Size" value is calculated using video segments
that contain the most information. You may still be able to
transfer (dub) even if the "Size" has exceeded "Destination
Capacity" when the video images contain little movement.
6
Press [3, 4] to select "Set" and
press [ENTER].
The transferring (dubbing) list is registered.
7
Press [3, 4] to select "Start
Dubbing" and press [ENTER].
When transferring (dubbing) the MPEG2 title to 5k high
speed recording compatible DVD-RAM
1 Press [3] to select "DVD drive speed".
2 Press [2, 1] to select "Maximum" or "Normal (Silent)" and
press [4].
≥Selecting "Normal (Silent)" means the noise generated by
this unit is less than "Maximum", however the time required
for transferring (dubbing) will increase (approximately)
double.
Press [2, 1] to select "Yes" and press [ENTER] to start
transferring (dubbing).
RQT7755
52
§
Size: 0MB
Name of item
New item
Next
Set
01/01
titles
∫ To edit the transferring (dubbing) list
Select the item in step 5 (➡left)
When transferring (dubbing) MPEG4 titles in "High
Speed" mode, "Move" is not displayed.
1 Press [SUB MENU].
2 Press [3, 4] to select the operation and press
[ENTER].
§
Multiple editing is possible (➡ below).
To cancel all registered transferring (dubbing) setting and lists
In step 3 (➡ page 51, right column)
1 Press [3, 4] to select "Cancel All" and press [ENTER].
2 Press [2, 1] to select "Yes" and press [ENTER].
≥The settings and lists may be cancelled in the following situations.
–When a title etc. has been recorded or erased at the transfer
(dubbing) source
–When steps have been taken, for instance, to turn off the unit,
open the tray, remove the card, change the transfer (dubbing)
direction, etc.
To show other pages
Press [3, 4, 2, 1] to select "Previous" or "Next" and press
[ENTER].
≥You can also press [:, 9] to show other pages.
Multiple editing
Select with [3, 4, 2, 1] and press [;]. (Repeat.)
Press [ENTER] to register to the list.
≥A check mark appears. Press [;] again to cancel.
≥When you switch between the "Video" and "PLAY LIST" tab, the
check mark is cancelled.
To stop transferring (dubbing)
Press and hold [RETURN] for 3 seconds.
To return to the previous screen
Press [RETURN].
[Note]
≥When a name has not been input for the transfer (dubbing) source
title, it is possible that this title's number will not be the same on the
transfer (dubbing) destination. It is recommended that you input a
title name before transferring (dubbing) (➡ page 42).
≥The sequence in which the MPEG4 titles are registered on the
transfer (dubbing) list may not be reflected at the transfer (dubbing)
destination.
Erase All
Add
Erase §
Move