Bluetooth Wireless Technology; Automatic Connection - Pioneer SP-SB23W Operating Instructions Manual

10
English

BlUetOOth wIreleSS teChNOlOgY

to use your Bluetooth
with the sp-sB23W speaker Bar system, you must
first pair your device with your speaker Bar.
pairing creates the ability for your Bluetooth
to connect with your speaker Bar wirelessly and
exchange information.
you only have to pair your speaker Bar with your
Bluetooth device one time for this exchange of
®
information to take place.
PaIr aND CONNeCt YOUr BlUetOOth DeVICe
1. Make sure your Bluetooth
Bar are powered on and the Bluetooth
is selected on the speaker bar (Blue light above
Bluetooth logo is solid blue).
®
2. activate the Bluetooth
Bluetooth source device and check it is actively
®
looking for a Bluetooth
3. press and hold the Bluetooth
the Bluetooth light begins to flash slowly.
®
4. your speaker bar will now appear on your
Bluetooth source device. select "sp-sB23W" on
®
your Bluetooth device to initiate pairing.
®
5. after a few seconds your speaker Bar will now be
paired with your Bluetooth
enjoy music playback wirelessly. Note: only one
device can be connected to the speaker Bar at
one time.
6. using the included remote for your speaker Bar,
you can track forward and back, pause and play
your current track, and turn the Volume up and
down.

aUtOmatIC CONNeCtION

any time you want to connect the last paired device
and play it through the speaker bar, do the following:
1. turn your device's Bluetooth
2. enter Bluetooth
®
source button from the remote.
NOTE: By default, the last connected Bluetooth
device will automatically connect if available.
hOw tO DISCONNeCt wIth a BlUetOOth DeVICe
turn off or disconnect the Bluetooth
Bluetooth device.
®
Not all features are available on all Bluetooth
source devices.
wireless technology device
®
®
device and speaker
®
source
®
function on your
®
device.
®
pairing button until
®
device and you can
®
function on.
®
source by pressing the Bluetooth
feature on your
®
teaChINg YOUr SPeaker Bar tO reSPOND tO
aNOther remOte CONtrOl
PrOgrAmmINg INSTruCTIONS: your speaker bar
is currently programmed to respond to the remote
control that is included with the product. However, we
device
strongly recommend programming the speaker bar to
also respond to your existing remote control using the
steps illustrated below. this will enable you to operate
all of your components using a single remote control.
While programming the speaker bar, ignore anything
that may be displayed on the tV screen.
Not all remote controls can be used to control the
Speaker Bar.
1. power on the speaker Bar and wait for the blue
light to become solid.
2. using the souRce button select either analog or
digital input.
3. press and hold the speaker Bar's BLuetootH/
paiRiNg/LeaRNiNg button until the Bluetooth
light flashes. Release the button. the light will now
turn solid blue.
4. press the button on the speaker Bar that you
would like to teach, the Bluetooth
begin to flash slowly.
5. point the remote control that you want to use for
your speaker bar and push the corresponding
command button that you chose in step 4.
6. the Bluetooth
and the mode light will flash green if the code
®
was accepted (if the mode light flashes red the
code was not accepted. Move the remote control
®
closer and push the button again). Now push your
remote's command button again and if the mode
light flashes green the command is now set.
7. Repeat this process for each button you would like
to teach your speaker bar.
8. to exit the learning mode press and hold the
BLuetootH/paiRiNg/LeaRN button until the
Bluetooth
Bluetooth
®
1'- 2'
light should begin flashing quickly
®
flashes. then release the button. the
®
light is now off.
®
®
light should