Service VP15S1 / F B/N1B/U1B VP15S1L / N1B/U1B Manual DLP Projector TABLE OF CONTENTS SECTION PAGE 1. TECHNICAL SPECIFICATIONS....................1 2. SERVICE TOOLS .......................... 1 3. ABOUT THE REPAIR METHOD ....................2 4. DISASSEMBLE PROCEDURE ..................... 3 5. COLOR WHEEL REPLACEMENT PROCEDURE / (Japan Ver.) ......... 9 / (11) 6.
Page 2
Parts for your MARANTZ equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.
1. TECHNICAL SPECIFICATIONS ❖ ❖ Optical characteristics General Panel 0.95 inch 16:9 Power requirement 1920 x 1080 pixels [/F] AC 100V, 50/60 Hz 1080p DLP ® chip [/N] AC 230V, 50 Hz [/U] AC 120V 60 Hz Lamp Super High Pressure 200W DC Power consumption <...
3. ABOUT THE REPAIR METHOD About service spare part supply of the PWB and OPTICAL ENGINE When the PWB and the UNIT are repaired, confi rm contents of the following. POS.NO DESCRIPTION How to repair P101 FORMATTER PWB PWB ASSY is replaced P201 FAN PWB Can be repaired on component level...
4. DISASSEMBLE PROCEDURE 1. Disassemble of the lens ring. 1) Turn the ring (170B) counter clockwise and remove the ring. 2) Remove 3 screws (167B) and remove the focus ring (165B). 160B 3) Remove 3 screws (162B) and remove the zoom ring (160B). 162B 165B Fig.1...
Page 6
4. Disassemble of the top case. 045B TOP CASE 1) Remove 4 screws (200B), 3 screws (045B) and the screw 045B 001B (202B) from the top and bottom case. 200B J334 2) Disconnect the 2 connectors (J334 and J329) from the top 202B 045B case.
Page 8
8. Disassemble of the OPTICAL ENGINE unit. LAMP CASE 150G 157G 153G 1) To remove a OPTICAL ENGINE unit (UN04), a procedure UN04 (Fig.10 - Fig.13) is required. Because the screw (157G) is LENS BASE 155G hidden by the duct of the fan for lamp cooling (M703). J021 2) Disconnect 4 connectors from (J205, J211, J221, J224) on P201.
Page 9
3)ネジ (207G) 4 本を外し BALLAST ユニットを取り外します。 注)BALLAST ユニットを取り外すには、ランプコネクターがレン ズベースの下側に有りますのでレンズベースを取り外して下 さい。( 図 8 参照 ) 10. Disassemble of the shield for PWB of bottom side. 311G 1) Remove 4 screws (311G) and remove the shield (310G) for 302G PWB. 310G 2) Remove 9 screws (302G) and the shield (300G) for PWB. 3) Remove the cover (484G).
Page 10
12. Disassemble of the SSB2 PWB, the SSB1 PWB and the 250G HDMI PWB. SSB2 PWB 247G P801 1) Remove 3 screws (247G) and the screw (250G). 247G 2) Disconnect 3 connectors (A : J501, J502 and J503) and the FPC(J505).
5. COLOR WHEEL REPLACEMENT PROCEDURE 1. Remove the 4 screws shown in the picture below and remove the top cover of the optical engine. Remove screw 4. Remove the screws at the front and back sides of the color wheel and remove the color wheel cover. Top cover 2.
Page 12
5. Remove the 3 hex-screws then remove the color wheel. (Caution) Remove hex-screws The rubber dumper are glued to the color wheel, Be careful and remove. The color wheel of VP-15S1 is not the same as VP-11S1, VP12S1 to VP12S4 and VP13S1. Be careful when exchange the color wheel.
6. ADJUSTMENT PROCEDURE 各調整が必要な場合 各調整が必要な場合 Cases Adjustment is needed Replaced item 交換したアイテム P701 PWB Board PK00 SSB PWB Kit 035G Color wheel UN04 Optical Engine Color Wheel Adjustment ○ ○ ○ ○ カラーホイール調整 Color Temperature Adjustment ○ ○ ○ ○ 色温度補正...
Page 16
調整が終了したら、 ボタンを押します。 6) When the adjustment is made, press ENTER button. ENTER ボタンを押し、サービスメニューを表示します。 7) Press MENU button to display the service menu. MENU ) 矢印ボタンを使い を選択し、 ボタ 8) With the direction buttons, select "Service Exit" and "Service Exit" ENTER ンを押します。 press ENTER button.
[B] Color Temperature Adjustment Procedure Press the ENTER button. The below message Color Temperature Adjustment appears on the screen. After replacing the lamp or in other cases where Initialize the lighting changes, color temperature can be adjusted using the color temperature sensor. In the adjustment procedure, you must first initialize the Press "Enter"...
Page 18
Fit the color temperature sensor onto the lens Press the ENTER button to return to the menu and disconnect the cable of the color and press the ENTER button. Color temperature sensor from the projector. temperature adjustment starts and the projector’s WARNING and STANDBY indicators begin flashing simultaneously.
Page 21
[C] Serial Number Installing Procedure 準備するもの 1. Necessary Equipments • RS232C ケーブル ストレート タイプ:メス⇔メス • RS232C cable (Straight type: Female to Female) • PC (Windows200 もしくは • PC (Windows 200 or XP) • PC にインストールされたシリアルナンバー書込みツール • Serial Number installing software "FwVpManf.exe" on the "FwVpManf.exe"...
Page 22
6) "Serial Number" ボタンをク リ ックすると書き込まれます。 6) Click "Serial Number" button to install. 7) Remove the main AC cable. Don’t power off by any other 電源ケーブルを抜いてください。 means. 確認のため、 電源ケーブルを差し、 プロジェクターをオンしてく 8) Connect the main AC cable and Press the POWER ださい。...
Page 23
11) Confirm the serial number on the window and the プロジェクターと のウイン ドウのシ リ アルナンバーと確認し てください。 projector. 12) Turn off the projector. プロジェクターの電源をオフします。...
Page 24
[D] Confirmation procedure of software version 準備するもの 1. Necessary Equipments コード " 00 63 63 " が出せるサービスリモコン A service remote controller that can output the RC5 code サービスリモコンを使用せず、本体のみでも調整できます "00 63 63". (The unit can adjust without a service remote controller.) 確認...
Page 25
[E] A/D コンバータ AD9888 の調整方法 [E] AD9888 Adjustment Method を信号発生器として用います。 調整に必要なもの [1] Necessaries • Desktop Windows PC (for signal generator) • 信号発生器として用いる • Video card (It has to be filled the following features. ex. • Windows 搭載 (バージョンは使用するグラフィックカー NVIDA GeForce6600) ドの要求による)...
Page 27
[4] How to setup the desktop PC for signal generator 信号発生用 の初期設定 1) After connecting all cables, press the power button on 接続後に VP-15S1 、 信号発生用 、 調整用 をそれぞれ立 the VP-15S1, and PC for signal generator and PC for ち上げる。 VP-15S1 を...
Page 28
6) Open the tab of GeForce 6600. 6) GeForce 6600 タブを開きます。 タブを展開すると Fig 5 の詳 細設定画面になります。 Fig 6. Property of screen 3 Fig 6. 画面のプロパティ 7) Select "Screen resolution & refresh rates", Change the 7) Screen resolution & refresh rates Screen を選択し、...
Page 29
Fig 9. ペイン ト画面 Fig 9.Screen of MS PAINT 3) To display the full screen of test pattern, click the "View" 全画面テス トパターン表示を行う為に上部にある表示をク リ ッ クし、 ビッ トマップ表示を選択します。 全画面にテス トパターンが of menu bar on the top of MS PAINT and select the bitmap view.
Page 30
Fig 11.Screen of AtAdAdjEng Fig 11. AtAdAdj_1_08 起動画面 5) Press the "SPACE" key on the keyboard of PC for Fig 12 のメ ッセ−ジを確認後、 手順 テス トパターンの表 adjustment. 示に従い、 信号発生用 で Black(0 % のファイルを開き 6) Confirms that the following message. ます。 全画面表示した信号を 端子に入力し、...
Page 31
Fig 13.Screen of AtAdAdjEng Fig 13. AtAdAdj_1_08 起動画面 1 1) Adjustment of copmponent (480p) コンポーネン ト (480p) の調整 Open the property of GeForce 6600 on the PC for signal 出力を変更した時と同様に画面のプロパティ から generator. GeForce6600 のプロパティ画面にします。 Fig 14.Screen of property for GeForce 6600 Fig 14.
Page 32
Fig 15.Screen of AtAdAdjEng Fig 15. AtAdAdj_1_08 起動画面 14) Press the "SPACE" key on the keyboard of PC for Fig 16 のメ ッセ−ジを確認後、 コンポーネン トに 480p adjustment. Cyan(100%) "SPACE" を入力し、 調整用 の キーを押しま 15) Confirms that the following message. す。 テス トパターンの出力は、 手順 テス...
Page 33
20) Press the "SPACE" key on the keyboard of PC for Fig 17. AtAdAdj_1_08 起動画面 adjustment. 21) Confirms that the following message. 480p ここまでの作業で の調整が終了します。 22) Adjustment of copmponent (720p) コンポーネン ト (720p) の調整 Open the property of GeForce 6600 on the PC for signal 720p にてコンポーネン...
Page 34
23) Select "nView Display Setting", and change the setting 画面のプロパティ から GeForce6600 のプロパティ画面 of "Current display" to HDTV. Select 720p on the Device に示す nView Disply Setting を選択し Device Settings か Settings and click the application. ら出力解像度 (720p) を選択します。 選択後、 適用をク リ ックしま 24) Input 100% saturation Yellow 720P/60Hz Component す。...
Page 35
31) Press the SPACE key on the keyboard of PC for 全ての調整終了後に Fig 18 に示すメ ッセージが現れます。 確認 adjustment. をしてからセッ トの電源を落としてください。 32) Confirms that the following message. 33) Press Standby button on the projector. 34) Remove all connection cables. Fig 18. 終了メ...
Page 36
please perform 480p-YUV adjustment process. When the adjustment problem occurs into 720p-YUV adjustment process Press ESC key on the key board. Adjustment process returns to an initial 720-YUV adjustment process. Again, please perform 720p-YUV adjustment process.
7. TROUBLESHOOTING AND HINT [1] Check list for Troubleshooting Symptom 1 Symptom 2 Condition check Check Locations 1. Is the voltage of 5V at P701-J302 (2 pin)? UN02, W013 ↓ 2. Is the voltage of 5V at P903-J329 (10 pin)? P701, W014 No STANDBY ↓...
Page 38
Symptom 1 Symptom 2 Condition check Check Locations Current 100mA or more 1. Is output current 100mA or less? is not accepted by specification. ↓ The voltage of 12V is not outputted to TRIG1. When the lamp lights up, is the voltage of 3.3V at P501- P701, W012 JL16 (11 pin) ↓...
Page 39
[2] The flow from IRIS Control 1) Refer to the schematic diagram of P201-2/2. 2) Q262 and Q264 is 74VHC123AFT "Mono stable multi vibrator". Q263 and Q265 is BA6951FS "DC motor driver". 3) Refer to the following timing chart. 4) IRIS1 or IRIS2 = "L" level (0V) ------- Iris is narrow. IRIS1 or IRIS2 = "H"...
Page 40
[3] The flow from turn on the projector to the picture projection 1) Turn on the projector. 2) P701-J302 (3 pin) "PWR-CTR" become to "H" level (3.3V). 3) P701-J301, P101-J005, P201-J201 and P601-JE05 are raised to true voltage. PCB - Connector Pin No.
Page 41
R049 "LAMPLIT" R048 and D002 "ASIC_REDAY" R073 And D001 "PWR_GOOD" 6) The drive signal (3 phase motor drive) output from P101-J008 The color wheel starts. 7) P101-J011 (1 pin) "SCI" of the control signal for the lamp ignition become to "H" level (5V). The lamp lights up.
Page 42
[4] DMD [1080p] Image Quality Specification Error definitions 1.1 Dark Blemish Major Dark Blemish Major Dark Blemish A blemish is an obstruction or reflection of light. Blue 60 Blue 60 This is dark visibility on light screen in the active area. Minor Dark Blemish Minor Dark Blemish This is any form and size.
Page 43
Screen image 2.1 Active Area The Active area is the active pixel area on image screen. This is visible white area when input signal is all white. 2.2 Border Area The border is described as the area outside of the active area. This is visible black outside white image when input signal is all white.
Page 44
3. Screen select for remote controller Component 1 Input video signal Component 2 Lens Iris on/off S-Video Illumination Iris on/off Video Raster (Black) Raster (White) Theater Standard Green Dynamic Blue Info. Resolution Full Horizontal Staircase Normal Vertical Staircase Cinema Color Bars Through Horizontal Ramp Zoom...
Page 45
7. TROUBLESHOOTING AND HINT [1] CHECK LIST FOR TROUBLESHOOTING 対処方法 症状 1 症状 2 確認手順 対象箇所 1. P701-J302 (2 pin) に の電圧が有りますか UN02, W013 ↓ 2. P903-J329 (10 pin) に の電圧が有りますか P701, W014 STANDBY LED が点灯 ↓ しない 3. P903-J329 (8 pin) に...
Page 50
[4] DMD 検査基準 エラーの種類 1.1 Dark Blemish( ダーク・ブレミッシュ ホコリ、キズなどによる光りの障害・反射 Major Dark Blemish Major Dark Blemish 明るい画面で暗くなって見える物 Blue 60 Blue 60 形、大きさは様々な物がある Minor Dark Blemish Minor Dark Blemish White White 1.2 Light Blemish( ライト・ブレミッシュ ホコリ、キズなどによる光りの障害・反射 Major Light Blemish Major Light Blemish 暗い画面で明るくなって見える物...
Page 51
画面 2.1 Active Area ( アクティブ・エリア 画素が動作する部分 白画面を投影した時、白くなる部分 2.2 Border Area( ボーダー・エリア アクティブ・エリアの外周部分、 60 inch の画面で数 の範囲 黒画面を投影した時、 Active Area の外枠で明るさが少し異なる部分 図 参照 60inch (152cm) ボーダー・エリア ボーダー・エリア 60 inch(152 cm) 60 inch(152 cm) 周囲 数 周囲 数 アクティブ・エリア 図 図 ボーダー・エリア...
Page 52
表 表示パターン−リモコン対比 Service Mode 内 Optics Check のリモコンキー−表示パターン対応表 Component 1 Input video signal Component 2 Lens Iris on/off S-Video Illumination Iris on/off Video Raster (Black) Raster (White) Theater Standard Green Dynamic Blue Info. Resolution Full Horizontal Staircase Normal Vertical Staircase Cinema Color Bars Through...
Page 53
[5] The DC voltage value which was measured POS. NO. PIN NO. VOLTAGE DEVICE PWB : P101 Input terminal : VIDEO Input signal : SMPTE Color Bar Equipment : Tester (DC Voltage mesure mode) POS. NO. PIN NO. VOLTAGE DEVICE Q007 ICS650-41 J006...
Page 54
PWB : P101 PWB : P201 POS. NO. PIN NO. VOLTAGE DEVICE 13.3 Menu : Display Installation Front BAT54SWT1 Menu : Picture Adjust Lamp Mode Normal Equipment : Tester (DC Voltage mesure mode) 13.3 BAT54SWT1 POS. NO. PIN NO. VOLTAGE DEVICE 13.3 13.3...
9. BLOCK DIAGRAM LVDS BUS A 16bits,CLK,SCTRL VIDEO Y 10bit Y/R ODD 10bit G 10bit VIDEO IN CB 10bit CB/G ODD 10bit B 10bit (Digital GF9351 CR 10bit CR/B ODD 10bit R 10bit LVDS BUS B 16bits,CLK,SCTRL UPD64011B TIMING ODD Micromirror VIDEO TIMIN G Image...
12. MICROPROCESSOR AND IC DATA Q205 : BA4051BF-E2 : Q260 : BA6951FS-E2 DECODER CTL AMP PREAMP + − RM1 / RM2 − + CS AMP TL AMP...
Page 84
Q521 : TE8200PF SYNC. SEPARATOR Q506 / Q507 : AD8185ARU FEATURES FUNCTIONAL BLOCK DIAGRAM Fully Buffered Inputs and Outputs Fast Channel-to-Channel Switching: 15 ns AD8183/AD8185 High Speed IN0A 380 MHz Bandwidth (–3 dB) 200 mV p-p DGND SELECT 310 MHz Bandwidth (–3 dB) 2 V p-p SEL A/B IN1A 1000 V/ s Slew Rate G = +1, 2 V Step...
Page 85
Q522 : AD9888 FEATURES FUNCTIONAL BLOCK DIAGRAM 205 MSPS Maximum Conversion Rate 500 MHz Programmable Analog Bandwidth 0.5 V to 1.0 V Analog Input Range OUTA CLAMP Less than 450 ps p-p PLL Clock Jitter @ 205 MSPS OUTB 3.3 V Power Supply Full Sync Processing OUTA CLAMP...
Page 86
Q522 : AD9888 Mnemonic Description Inputs Channel 0 Analog Input for RED Channel 0 Analog Input for GREEN Channel 0 Analog Input for BLUE Channel 1 Analog Input for RED Channel 1 Analog Input for GREEN Channel 1 Analog Input for BLUE These high impedance inputs that accept the RED, GREEN, and BLUE channel graphics signals, respectively.
Page 87
Q522 : AD9888 Mnemonic Description CKINV Sampling Clock Inversion (Optional) This pin may be used to invert the pixel sampling clock, which has the effect of shifting the sampling phase 180°. This is in support of Alternate Pixel Sampling mode, wherein higher frequency input signals (up to 410 Msps) may be captured by first sampling the odd pixels, then capturing the even pixels on the subsequent frame.
Page 88
Q522 : AD9888 Mnemonic Description FILT External Filter Connection For proper operation, the pixel clock generator PLL requires an external filter. Connect the filter shown in Figure 6 to this pin. For optimal performance, minimize noise and parasitics on this node. Power Supply Main Power Supply These pins supply power to the main elements of the circuit.
Page 89
Q529 : µPD64011BGM 10 BIT VIDEO DECODER...
Page 92
99MZZ27AV8000 99MZZ27AV8000 PWB ASSY SSB2 PWB ASSY P901 PWB ASSY IR-FRONT PWB ASSY P902 PWB ASSY IR-REAR PWB ASSY P903 PWB ASSY KEY PWB ASSY NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 93
CUSHION BOTTOM 023S 00M07AV809120 CUSHION CUSHION TOP 035S 00M29AV801010 PACKING CASE PACKING CASE VP-15S1 039S 00M07AV805010 MASS CARTON MASTER CARTON 035Z 00M413V067010 CAP CAP PRODUCTION LENS NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 94
99MZZ27AV8000 99MZZ27AV8000 PWB ASSY SSB2 PWB ASSY P901 PWB ASSY IR-FRONT PWB ASSY P902 PWB ASSY IR-REAR PWB ASSY P903 PWB ASSY KEY PWB ASSY NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 95
CUSHION BOTTOM 023S 00M07AV809120 CUSHION CUSHION TOP 035S 00M29AV801010 PACKING CASE PACKING CASE VP-15S1 039S 00M07AV805010 MASS CARTON MASTER CARTON 035Z 00M413V067010 CAP CAP PRODUCTION LENS NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
14. ELECTRICAL PARTS LIST NOTE ON SAFETY FOR FUSIBLE RESISTOR : PARTS INFORMATION RESISTORS The suppliers and their type numbers of fusible resistors 1) 00MGD05 × × × 140, Carbon film fixed resistor, ±5% 1/4W are as follows; 2) 00MGD05 × × × 160, Carbon film fixed resistor, ±5% 1/6W 1.
Page 97
UMD9NTR P201 Q233 00MBA30003210 00MBA30003210 TRS. UMD9NTR P201 Q234 00MBA30003210 00MBA30003210 TRS. UMD9NTR P201 Q240 00MHC91915210 00MHC91915210 IC BA00ASFP P201 Q241 00MBA30003210 00MBA30003210 TRS. UMD9NTR NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 98
00MNN05563610 CHIP RES. 56K OHM +-5% 1/16W P201 R254 00MNN05124610 CHIP RES. 120K OHM +-5% 1/16W P201 R255 00MNN05683610 CHIP RES. 68K OHM +-5% 1/16W NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 99
100UF/ 16V P501 CL21 00MEY10601070 00MEY10601070 TANTL.CAP CHIP 10UF/ 10V P501 CL22 00MEY10701620 00MEY10701620 ELECT CAP. 100UF/ 16V P501 CL23 00MEY10701620 00MEY10701620 ELECT CAP. 100UF/ 16V NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 100
00MLU17103010 CHIP INDUCTANCE NLC322522 10UH P501 LL20 00MLU17103010 00MLU17103010 CHIP INDUCTANCE NLC322522 10UH P501 LL21 00MFM31101020 00MFM31101020 EMI FILTER NFM2012R03C101R P501 LL22 00MFM31101020 00MFM31101020 EMI FILTER NFM2012R03C101R NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 101
C530 00MEY10601670 00MEY10601670 TANTL.CAP CHIP MSVB21C 10UF/16V P801 C531 00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C532 00MEY10601670 00MEY10601670 TANTL.CAP CHIP MSVB21C 10UF/16V NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 102
00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C598 00MEY10601670 00MEY10601670 TANTL.CAP CHIP MSVB21C 10UF/16V P801 C599 00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 103
C5H6 00MEY10601070 00MEY10601070 TANTL.CAP CHIP 10UF/ 10V P801 C5H7 00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C5H8 00MEY10601070 00MEY10601070 TANTL.CAP CHIP 10UF/ 10V NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 104
00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C5S2 00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C5S3 00MEY10601070 00MEY10601070 TANTL.CAP CHIP 10UF/ 10V NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 105
00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C628 00MEY10601670 00MEY10601670 TANTL.CAP CHIP MSVB21C 10UF/16V P801 C629 00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 106
00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C6A7 00MDK96104200 CER. CAP. 0.1 UF +-10% B 10V P801 C6A8 00MEY10601070 00MEY10601070 TANTL.CAP CHIP 10UF/ 10V NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 107
00MLU15393010 CHIP INDUCTANCE NL252018 39UH P801 L530 00MLU15153010 00MLU15153010 CHIP INDUCTANCE NL252018-150J P801 L531 00MLU17103010 00MLU17103010 CHIP INDUCTANCE NLC322522 10UH P801 Q501 00MHC12245990 00MHC12245990 IC OPA2690ID NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 108
00MNN05750610 CHIP RES. 75 OHM +-5% 1/16W P801 R546 00MNN05104610 CHIP RES. 100K OHM +-5% 1/16W P801 R547 00MNN05750610 CHIP RES. 75 OHM +-5% 1/16W NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 109
00MNN05391610 CHIP RES. 390 OHM +-5% 1/16W P801 R5C5 00MNN05391610 CHIP RES. 390 OHM +-5% 1/16W P801 R5C6 00MNN05750610 CHIP RES. 75 OHM +-5% 1/16W NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 110
00MNN05220610 CHIP RES. 22 OHM +-5% 1/16W P801 R5P6 00MNN05220610 CHIP RES. 22 OHM +-5% 1/16W P801 R5P7 00MNN05220610 CHIP RES. 22 OHM +-5% 1/16W NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 111
00MNN05105610 CHIP RES. 1M OHM +-5% 1/16W P801 R629 00MNN05102610 CHIP RES. 1K OHM +-5% 1/16W P801 R630 00MNN05473610 CHIP RES. 47K OHM +-5% 1/16W NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 112
00MHZ20018050 00MHZ20018050 CHIP DIODE 1SS302 P903 D4W3 00MHZ20018050 00MHZ20018050 CHIP DIODE 1SS302 P903 D4W4 00MHI10042080 00MHI10042080 L.E.D. SECT1E01C-S P903 D4W9 00MHI10108210 00MHI10108210 L.E.D. SML-010YT T86/(YELLOW) NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
Page 113
00MSP01013810 PUSH SW SKHUPFE010 ALPS TACT SWITCH P903 S4W9 00MSP01013810 00MSP01013810 PUSH SW SKHUPFE010 ALPS TACT SWITCH INLET PWB P904 (00MWG413V904-) P904 EN01 00MYJ04002590 00MYJ04002590 JACK !N9226-6102 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
15. ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE When replaced of the U-PRO (Microprocessor) or the Flash ROM, confirm contents of the following. Pos. After Description Part Name Remark Name replaced P101 Q006 JS28F320C3BD70 FOR VP15S1 FORMATTER IC (EEPROM) Replacement by PWB ASSY.