DGTEC DG-SD3401 User Manual page 7

Note: The default is OFF, set this option to
connected to an active antenna which amplifies the received RF signal,
otherwise please set it to OFF .
2.2.1.2 Country Setting
Set the country for Auto Scan, Manual Scan and Time Zone.
Note: Change to Country Setting will automatically change the
default Time Zone and set the default Frequency and Bandwidth for
Auto Scan.
2.2.1.3 OSD Language
Set the On Screen Display Language.
2.2.1.4 Audio Language
Set the audio language for watching program.
2.2.1.5 Subtitle Language
Set the language for displaying subtitle.
2.2.1.6 LCN
Set the Logical Channel Number to on or off.
Note: LCN is a number that uniquely identifies a logical channel,
NOTE-Always set to ON
2.2.1.7 Daylight Saving/Region Setting/Time Zone
Allows you to enable or disable daylight saving. If you know the region of
your location,select an appropriate Region Setting or set the Time Zone
offset manually.
2.2.1.8 Auto Scan
Press <RED> button to start Auto Scan. See section 1.2.1 for details.
2.2.1.9 Manual Scan
Press <GREEN> button to start Manual Scan. See section 1.2.2 for details.
2.2.2 TV Setup
Setup the display mode for TV.(Optional) See Figure 3.
SETUP. TV Setup 01/01/2008 00:19
4:3 LB
TV Format
TV Mode PAL
OSD Transparency 6
Banner Display Time 3S
Video Output CVBS+RGB
Video Enhancement OFF
5761 Move Switch Exit
Figure 3. TV Setup Figure 4. Video Enhancement
2.2.2.1 TV Format
ON only if this STB is
Set display format for sizing screen, such as 4:3LB, 4:3PS,
16:9PB,16:9 FIT.
4:3LB(LetterBox): Typically for wide screen content displays on
conventional 4:3 TV with black bars above and below the picture.
4:3PS(PanScan): Typically for wide screen content displays on
conventional 4:3 TV with left and right edges cropped.
16:9PB(PillarBox)/16:9 FIT: Typically for wide screen 16:9 TV.
2.2.2.2
Set PAL, NTSC or AUTO for display. AUTO will switch PAL or NTSC
by program content. This setting should be matched with user's TV.
2.2.2.3 OSD Transparency
Set the On Screen Display transparency. 1 is the most transparent.
2.2.2.4 Banner Display Time
Set Banner displays time. Banner doesn't disappear when set as
Always
2.2.2.5 Video Output
Set the video output mode to TV.
2.2.2.6 Video Enhancement
Set the Video Enhancement. See Figure 4.
(1) Press <Up/Down> button to select Video Enhancement option.
(2) Press <Left/Right> button to set Video Enhancement.
(3) Press <Up/Down> button to select Flesh Tone or Black/White
Expansion.
(4) Press <Left/Right> button to set Flesh Tone and Black/White
Expansion.
2.2.3 Password
Set password for menu lock or channel lock or censorship lock. And the
user can change password here, the default PIN Code is 6666.
2.2.3.1
Lock the menus by password.
2.2.3.2
Lock the channel which has been set to lock status when turning on the
Channel Lock. Please see section 2.3.1.2 for details.
2.2.3.3
Lock the program by password and censorship threshold.
The censorship info is in program content. Under the censorship rating,
Flesh Tone OFF
user has to enter the right password for watching program.
Black/White Expansion OFF
2.2.3.4
Move Switch Exit
To change the PIN code, select this option, press <Left/Right> button
to trigger changing password and <0~9> buttons to enter old password,
new password and confirm new password. If successful,the PIN Code
Changed message will be displayed, otherwise the PIN Code Error
message will be displayed.
4
Note:Most settings are automatically set upon scanning the unit in.
TV Mode
and disappears at timeout when set as other values.
Menu Lock
Channel Lock
Censorship Lock
Change Password