Page 1 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router Rev: 1.0.0 1910011437...
Page 2 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
Page 3: Fcc Statement
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 4: Rf Exposure Information
RF Exposure Information This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:...
Page 5: Industry Canada Statement
1） l’appareil ne doit pas produire de brouillage; 2） l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
Page 6: Safety Information
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information When product has power button, the power button is one of the way to shut off the product; ...
Page 7: Declaration Of Conformity
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 300Mbps Wireless N VoIP VDSL/ADSL Modem Router Model No.: TD-VG5612 Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:...
Page 8: Table Of Contents
CONTENTS Package Contents ........................ 1 Chapter 1. Product Overview .................... 2 1.1 Overview of the Modem Router ..................2 1.2 Main Features ........................3 1.3 Panel Layout........................4 1.3.1 The Front Panel ......................4 1.3.2 The Back Panel ......................6 Chapter 2. Connecting the Modem Router ..............7 2.1 System Requirements .......................7 2.2 Installation Environment Requirements ................7 2.3 Connecting the Modem Router ..................7...
Page 9 4.7.1 DHCP Settings ......................53 4.7.2 Clients List......................... 55 4.7.3 Address Reservation ....................55 4.7.4 Conditional Pool......................56 4.8 Wireless ...........................57 4.8.1 Basic Settings......................57 4.8.2 WPS Settings ......................59 4.8.3 Wireless Security ....................... 62 4.8.4 Wireless Schedule ..................... 64 4.8.5 Wireless MAC Filtering ....................
Page 10 4.12.3 RIP Settings ......................93 4.13 IPv6 Route Settings ......................93 4.13.1 IP v6 Default Gateway ....................93 4.13.2 IP v6 Static Route ...................... 94 4.14 Forwarding ........................95 4.14.1 Virtual Servers ......................95 4.14.2 Port Triggering......................97 4.14.3 DMZ ........................98 4.14.4 UPnP ........................
Page 11 4.23.9 Reboot ........................123 4.23.10 Statistics ......................123 4.24 Logout ..........................125 Appendix A: Specifications ................... 126 Appendix B: Troubleshooting..................127 Appendix C: Telephony Features ................133...
Page 12: Package Contents
Package Contents The following contents should be found in your package: One TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router  One Power Adapter for TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router  Quick Installation Guide  Telephony Feature Guide ...
Page 13: Chapter 1. Product Overview
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Chapter 1. Product Overview Thank you for choosing the TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router. 1.1 Overview of the Modem Router The TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router integrates 4-port Switch, Firewall, NAT-Router and Wireless AP.
Page 14: Main Features
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 1.2 Main Features Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps (2.4GHz).  Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), three RJ11 ports (one ...
Page 15: Panel Layout
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 1.3 Panel Layout 1.3.1 The Front Panel Figure 1-1 The modem router’s LEDs are located on the front panel (View from left to right). They indicate the device’s working status. For details, please refer to LED Explanation.
Page 16 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide The wireless function is disabled. The corresponding phone is off-hook. VoIP1/ VoIP2 The corresponding phone is on-hook. It turns on when a WPS synchronization is established and On/Off automatically turns Off about five minutes later.
Page 17: The Back Panel
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 1.3.2 The Back Panel Figure 1-2 Wi-Fi: The switch for the Wi-Fi function is on the top. Press the button to enable/disable the  Wi-Fi function. WPS: The switch for the WPS function is on the top. For details, please refer to 4.8.2 WPS...
Page 18: Chapter 2. Connecting The Modem Router
Plug one end of the twisted-pair DSL cable into the DSL port on the rear panel of TD-VG5612. Connect the other end to the MODEM port of the external splitter. Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the modem router TD-VG5612.
Page 19 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 2-1...
Page 20: Chapter 3. Quick Installation Guide
300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router using Quick Setup Wizard within minutes.
Page 21: Quick Installation Guide
192.168.1.2 ~ 192.168.1.254. 3.2 Quick Installation Guide With a Web-based management page, it is easy to configure and manage the TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router. The Web-based management page can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
Page 22 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 3-5 Select your Region and Time Zone from the drop-down list, then click Next. Figure 3-6 Select “Yes” to auto detect your connection type and then click Next. It will take about two...
Page 23 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 3-7 Configure parameters for WAN connection. Here we take PPPoE as an example. Enter the username and password provided by your ISP. Click Next. Figure 3-8 3G/4G Router Mode can be set as a backup Internet access method. If you do not want to configure 3G/4G settings now, just click Next to continue.
Page 24 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 3-10 The wireless function is enabled by default. You can rename your wireless network name and create your own password in this page. The default wireless name is TP-LINK_XXXXXX.
Page 25 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 3-12 10. You will see the Complete screen below, click Finish to complete these settings. Figure 3-13...
Page 26: Chapter 4. Configuring The Modem Router
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Chapter 4. Configuring the Modem Router This chapter will show each Web page's key function and the configuration. 4.1 Login After your successful login, you will see the twenty-two main menus on the left of the Web-based management page.
Page 27: Quick Setup
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-1 4.3 Quick Setup Please refer to Section 3.2 Quick Installation Guide. 4.4 Operation Mode Choose “Operation Mode”, and you will see the screen as shown in Figure 4-2. Select your...
Page 28: Network
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-2  DSL Modem Router Mode: In this mode, the device enables multi-users to share Internet via ADSL/VDSL using its DSL port and share it wirelessly at 300Mbps wireless 802.11n speeds.
Page 29: Wan Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.5.1 WAN Settings Choose “Network”“WAN Settings”, and you will see the WAN Port Information Table in the screen similar to Figure 4-3. 4.5.1.1 VDSL WAN Settings For VDSL mode, there are four different connection types, which are Static IP, Dynamic IP, PPPoE and Bridge.
Page 30 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-4 DSL Modulation Type: DSL Modulation Type: The modem router supports two modulation types: ADSL and VDSL,  you can select the corresponding types according to your needs. PTM Configuration: Enable VLAN ID: Check the box to enable the Virtual LAN ID.
Page 31 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-5 WAN Service Setup: Enable IPv4：Check the box to enable IPv4.  IP Address: Enter the IP address in dotted-decimal notation provided by your ISP.  Subnet Mask: Enter the subnet Mask in dotted-decimal notation provided by your ISP, ...
Page 32: Dynamic Ip
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide IPv6 Address: Enter the IPv6 address provided by your ISP.  Prefix Length: Enter the prefix length of the IPv6 address. The default value is 64.  IPv6 Gateway: Enter the gateway IPv6 address provided by your ISP.
Page 33 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-6 Click Advance, advanced selections for WAN Service Setup can be shown.  MTU (Bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.
Page 34 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Internet, please select the check box. If another Router exists in your network, you don’t need to select the option.  Enable Fullcone NAT: It is a type of NAT, if not enabled, the default NAT will act.
Page 35 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-7 PPP Username/Password/Confirm password: Enter the User Name, Password and  Confirm password provided by your ISP. These fields are case-sensitive. Connection Mode: For PPPoE connection, you can select Always on or Connect on ...
Page 36 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide MTU (Bytes): Maximum Transmission Unit Size. Check this box then you can change the  MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.
Page 37 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.5.1.2 ADSL WAN Settings For ADSL mode, there are six different configurations for the connection types, which are Static IP, Dynamic IP, PPPoE, PPPoA, IPoA and Bridge. You can select the corresponding types according to your needs.
Page 38 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide ATM Configuration: VPI (0~255): Identifies the virtual path between endpoints in an ATM network. The valid range  is from 0 to 255. Please input the value provided by your ISP.
Page 39 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-11 Click Advance, advanced selections of ATM Configuration can be shown. Encapsulation Mode: Select the encapsulation mode for the Static IP Address. Here you  can leave it default.
Page 40 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Subnet Mask: Enter the subnet Mask in dotted-decimal notation provided by your ISP,  usually is 255.255.255.0. Gateway (Optional): Enter the gateway IP address in dotted-decimal notation provided by ...
Page 41 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-12...
Page 42 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Click Advance, advanced selections for WAN Service Setup can be shown.  MTU (Bytes): Maximum Transmission Unit Size. Check this box then you can change the MTU size. The default MTU value is 1500 Bytes. It is not recommended that you change the default value unless required by your ISP.
Page 43 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-13 PPP Username/Password/Confirm Password: Enter the User Name, Password and  Confirm Password provided by your ISP. These fields are case-sensitive. Connection Mode: For PPPoE connection, you can select Always on or Connect on ...
Page 44 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide IPv6 Default Gateway: Select a WAN connection from the drop-down list as the IPv6 default  gateway. Click Advance, advanced selections for WAN Service Setup can be shown. Service Name/Server Name: Enter the Service Name and Server Name if it was provided by ...
Page 45 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-14 IPoA If your ISP provides an IPoA connection, select IPoA option for the Connection Type on the screen.
Page 46 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-15 IP Address/Subnet Mask: Enter the IP Address and Subnet Mask provided by ISP. If you  forget, you can ask your ISP. Gateway: Enter the gateway IP address in dotted-decimal notation provided by your ISP.
Page 47: 4G Settings
Some 3G/4G USB modem may not be supported by the modem router. For more information, please refer to Compatibility List on our website: www.tp-link.com. If your 3G/4G USB modem is incompatible with our modem router, please contact our technical support by referring to the...
Page 48 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-17 Location: Please select the location where you're enjoying the 3G/4G card.  Mobile ISP: Please select the ISP (Internet Service Provider) you apply to for 3G/4G service. ...
Page 49 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Connect manually: You can click the Connect/Disconnect button to connect/disconnect  connection immediately. This mode also supports the Max Idle Time function as Connect on demand mode. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field.
Page 50: Interface Grouping
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide  Note: After connecting a 4G modem to the modem router, please access the Web-based management page by typing http://tplinkmodem.net/ in the address field of the browser and press Enter.
Page 51: Lan Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-21 Click Save to make the entry effective immediately 4.5.4 LAN Settings Choose “Network”“LAN Settings” menu, and you will see the LAN screen (shown in Figure 4-22). Please configure the parameters for LAN ports according to the descriptions below.
Page 52 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-22 IP Address: You can configure the modem router’s IP Address and Subnet Mask for LAN  Interface. • IP Address: Enter the modem router’s local IP Address, then you can access to the Web-based management page via the IP Address, the default value is 192.168.1.1.
Page 53: Ipv6 Lan Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide • Lease Time: The Lease Time is the amount of time in which a network user will be allowed connection to the modem router with their current dynamic IP address. Enter the amount of time, in hours, then the user will be “leased”...
Page 54 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-24 Start IPv6 Address: Enter a value for the DHCPv6 server to start with when issuing IPv6 • addresses. End IPv6 Address: Enter a value for the DHCPv6 server to end with when issuing IPv6 •...
Page 55: Mac Clone
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Site Prefix: Enter a value for the site prefix. • Site Prefix Length: Enter a value for the site prefix length. • Click the Save button to save the settings.
Page 56 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-28 Virtual Private Network (VPN): VPN Passthrough must be enabled if you want to allow VPN  tunnels using VPN protocols to pass through the modem router. PPTP Passthrough: Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point •...
Page 57: Dsl Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Click the Save button to save your settings. 4.5.8 DSL Settings Choose “Network”“DSL Settings”, you can select the DSL Modulation Type and Annex Type in the next screen. The DSL feature can be selected when you meet the physical connection problem.
Page 58  Note: You could also use other VPN Routers to set VPN tunnels with TD-VG5612. TD-VG5612 supports up to 10 VPN tunnels simultaneously. Click Add New Connection in Figure 4-30 and then you will enter the screen shown in Figure...
Page 59 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-31  IPSec Connection Name: Enter a name for your VPN.  Remote IPSec Gateway Address (URL): Enter the destination gateway IP address in the box which is the public WAN IP or Domain Name of the remote VPN server endpoint. (For example: Input 219.134.112.247 in Device1, Input 219.134.112.246 in Device 2)
Page 60 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-32  Authentication Method: Select Pre-Shared Key (recommended).  Pre-Shared Key: Enter the Pre-shared Key for IKE authentication, and ensure both the two peers use the same key. The key should consist of visible characters without blank space.
Page 61 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Settings for Phase 1:  Mode: You can select Main or Aggressive. Select Main to configure the standard negotiation parameters for IKE phase1. Select Aggressive to configure IKE phase1 of the VPN Tunnel to carry out negotiation in a shorter amount of time.
Page 62: Iptv
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide  Note: If you want to change the default settings of Advanced Settings, please make sure that both VPN server endpoints use the same Encryption Algorithm, Integrity Algorithm, Diffie-Hellman Group and Key Life time in both phase1 and phase2.
Page 63 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-35 Enable IPTV: Check the box to enable IPTV function.  Enable a wireless connection for IPTV: If enabled, the set-top box can connect wirelessly  to the modem router. To use this function, follow the steps below: Select Enable IPTV.
Page 64: Dhcp Server
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide DSL Modulation Type: The modem router supports two modulation types: ADSL and VDSL,  you can select the corresponding types according to your needs. If you choose "ADSL", you will see the screen as shown in the following figure: VPI (0-255): Identifies the virtual path between endpoints in an ATM network.
Page 65 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-37 Start IP Address: Enter a value for the DHCP server to start with when issuing IP addresses.  The default Start IP Address is 192.168.1.100. End IP Address: Enter a value for the DHCP server to end with when issuing IP addresses.
Page 66: Clients List
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide  Note: To use the DHCP server function of the modem router, you must configure all computers on the LAN as "Obtain an IP Address automatically". You have to disable NAT of the WAN connections, or the DHCP Relay may not take effect.
Page 67: Conditional Pool
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide notation) of the computer for which you want to reserve an IP address. Click the Save button. Figure 4-41 To modify or delete an existing entry: Click the Edit in the entry you want to modify. If you want to delete the entry, click the Delete.
Page 68: Wireless
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-43 To modify or delete an existing entry: Click the Edit in the entry you want to modify. If you want to delete the entry, click the Delete. Modify the information.
Page 69 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-44  SSID: Wireless network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard).
Page 70: Wps Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide  Note: If 11b only, 11g only, or 11bg mixed is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed.
Page 71 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-45 WPS: Enable or disable the WPS function here.  Current PIN: The current value of the modem router's PIN is displayed here. The default PIN  of the modem router can be found in the label or User Guide.
Page 72 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide You can also keep the default WPS Status as Enabled and click the Add device button in Figure 4-45, then Choose “Press the button of the new device in two minutes” and click Connect.
Page 73: Wireless Security
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-47 Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Connect button. Step 3: “Connect successfully” will appear on the screen of Figure 4-47, which means the client device has successfully connected to the modem router.
Page 74 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-48 Disable Wireless Security: If you do not want to use wireless security, check this radio  button. But it’s strongly recommended to choose one of the following modes to enable security.
Page 75: Wireless Schedule
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide WPA/WPA2-Personal security on the drop-down list. The default setting is Auto, which can select WPA-PSK or WPA2-PSK authentication type automatically based on the wireless station's capability and request. Encryption: You can select Auto, TKIP or AES as Encryption.
Page 76: Wireless Mac Filtering
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-49  Note: The time you set is the period you need the wireless off. Before configure the wireless schedule, please set system time first which refer to 4.22.2 Time Settings, then you can enable or disable Wireless Schedule.
Page 77 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-50 To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address: The wireless station's MAC address that you want to filter.  Status: The status of this entry either Enabled or Disabled.
Page 78: Wireless Advanced
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Click the Enable/ Disabled Selected button to make selected entries enabled or disabled. Click the Delete Selected button to selected entries. For example: If you desire that the wireless station A with MAC address 00:1D:0F:11:22:33 and the...
Page 79: Wireless Status
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Transmit Power: Here you can specify the transmit power of modem router. You can select  High, Middle or Low which you would like. High is the default setting and is recommended.
Page 80: Guest Network
SSID: The guest network name. When setting up a Guest network, it is strongly  recommended to use a name that easily distinguishes it from your primary network. The default SSID is set to be TP-LINK Guest Security: The default value is disabled, but it’s strongly recommended to enable ...
Page 81: Guest Network Status
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Wireless Password: You can enter ASCII characters between 8 and 63 characters or 8 to 64  Hexadecimal characters. Group Key Update Period: Specify the group key update interval in seconds. The value ...
Page 82: Sip Account
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.10.1 SIP Account Choose “Voice”“SIP Account”, you will see the screen similar to Figure 4-56. SIP accounts are necessary for making VoIP calls. This section introduces how to setup the SIP(Session Initiation Protocol) account for your Modem Router.
Page 83 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-57 SIP Account Basic Settings Phone Number/User ID: Enter the phone number of the account you applied.  Authentication ID: Enter the name or number used for SIP Authorization with SIP Registrar.
Page 84: Dial Plan
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Incoming Call Route: Select which line the incoming VoIP call will be routed to.  None: All incoming VoIP calls will be denied. • • Phone 1/Phone 2: The incoming call will be routed to either Phone1 or Phone 2 randomly.
Page 85 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Destination: Displays the account or network used for this plan.  Enable: Displays the interface(s) enabled in this plan.  Remove: Check the box and then click the Remove button below so that the very plan will ...
Page 86: Warmline
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Take the 2 dial plan in Figure 4-59 as an example. If you dial 186666, number 18655556666 will be dialed out to make a call. Add Number – If it is selected, the original phone number will be sent out with what you •...
Page 87: Call Blocks
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-61 Phone Enable: Check the box behind to enable the function.  Dial Plan Priority: The parameters configured here determine which SIP account to use  when making outgoing calls. Auto means no priority.
Page 88 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-62 DND(Do not disturb): Check the box to deny all incoming calls.  Period: Choose DND is effective on which days.  DND Time: Choose DND is effective from what time to what time.
Page 89: Call Forward
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Outgoing Calls: Click Add to add a number or call type to be blocked from dialing out.  Figure 4-65 Add number prefix: Enter the number prefix. Numbers with this prefix is not allowed to •...
Page 90: Advanced Setup
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-67 Click the Save button to make the configuration take effect. 4.10.7 Advanced Setup Choose “Voice”“Advanced Setup”, you will see the next screen in Figure 4-68. Figure 4-68...
Page 91: Speed Dial
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Bound Interface Name: Bound Interface decides where to send/receive the VOIP traffic.  Easy way to select the interface is to check the location of the SIP server. If it locates some where in the Internet then select Any_WAN.
Page 92: Call Log
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-69 To add a Speed Dial entry, click the Add button and you will see the screen as shown in Figure 4-70. Fill in the following parameters and then click the Save button.
Page 93: Usb Voice Mail
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-72 Call Log: Check the Enable if you want to make this function take effect; otherwise check the  Disable. Call Type: Choose a type from the drop-down list, and the call log of this type will show on the ...
Page 94 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Selected: Check the box to select the corresponding voice message.  To refresh the web page, click Refresh button. To delete a voice message, check the Selected box and then click Remove button.
Page 95: Feature Code Setting
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Input the PIN code according to the notification. You can listen to all the new messages after the PIN code is validated. Click Save to save your configurations. Click Back to go back to the previous page, i.e. Figure 4-73.
Page 96: Usb Mass Storage
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.11.1 USB Mass Storage Choose menu “USB Settings → USB Mass Storage”, you can configure a USB disk drive attached to the modem router and view volume and share properties such as share name, capacity, status, and action, etc on this page as shown below.
Page 97: Storage Sharing
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide address field of your browser or Windows Explorer, such as. \\192.168.1.1. FTP Server users can log into the FTP Server via FTP Client. There are five users here, which provide means to control the access to the USB mass storage by Storage Sharing or FTP.
Page 98 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-78 Server Status: Indicates the Storage Sharing's current status.  Anonymous access to all the volumes: This function is enabled by default, so users can  access all activated volumes of Storage Sharing without accounts. If you want to add a shared folder which does not allow anonymous login, uncheck the box to disable this function.
Page 99: Ftp Server
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-80 Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings.
Page 100 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-81 Server Status: Indicates the FTP Server's current status.  Internet Access: If Internet Access is enabled, user(s) in public network can access FTP  server via Internet Address.
Page 101: Media Server
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-82 Click the Browse button, and then select the Select Volume from the drop-down list. Enter display name of the share folder in Share Name filed. Click the Apply button to apply the settings.
Page 102: Route Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Server Enable: Select this box to enable this function.  Server Name: The name of this Media Server.  To add a new share folder for your media server, please follow the instructions below: Click Add New Folder button, and you will see the screen as shown in Figure 4-84.
Page 103: Static Route
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-85 Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. 4.12.2 Static Route Choose “Route Settings” “Static Route”. You can see the Static Route screen, this screen allows you to configure the static routes (shown in Figure 4-86).
Page 104: Rip Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Gateway: Here you should type the Gateway address correctly, and the option for Interface  will adopt the default Gateway address for the Static Route. Interface: Select the Interface name in the text box, or else, the default Use Interface will be ...
Page 105: Ipv6 Static Route
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-89 Click the Add Interface button, you can add WAN Interfaces. Click the Save button to save your settings. 4.13.2 IPv6 Static Route Choose “IPv6 Route Settings” “IPv6 Static Route”. You can see the IPv6 Static Route screen.
Page 106: Forwarding
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Gateway: Type in the correct IPv6 Gateway address for the IPv6 Static Route.  Interface: Select the Interface from the drop-down list.  Status: Select Enabled or Disabled from the drop-down list.
Page 107 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide You can leave it blank if the Internal Port is the same as the Service Port, or enter a specific port number when Service Port is a single one. Protocol: The protocol used for this application, either TCP, UDP, or All (all protocols ...
Page 108: Port Triggering
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Otherwise there will be a conflict to disable the virtual server. 4.14.2 Port Triggering Choose menu “Forwarding”→ “Port Triggering”, you can view and add port triggering in the next screen (shown in Figure 4-94). Some applications require multiple connections, like Internet games, video conferencing, Internet telephoning and so on.
Page 109: Dmz
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide supported by the modem router). Open Port: The port or port range used by the remote system when it responds to the  outgoing request. A response using one of these ports will be forwarded to the PC which triggered this rule.
Page 110: Upnp
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-96 To assign a computer or server to be a DMZ server: Click the Enable button. Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address field.
Page 111: Parent Control
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Click the Disable button to disable UPnP. Click the Refresh button to update the Current UPnP Settings List. 4.15 Parent Control Choose menu “Parent Control”, and you can configure the parental controls in the screen as shown in Figure 4-98.
Page 112: Firewall
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.16 Firewall There are four submenus under the Firewall menu: Rule, LAN Host, WAN Host and Schedule. Click any of them, and you will be able to configure the corresponding function.
Page 113: Lan Host
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide The methods to add a new rule: Click the Add New button and the next screen will pop up as shown in Figure 4-100. Give a name (e.g. Rule_1) for the rule in the Description field.
Page 114: Wan Host
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide To add a new entry, please follow the steps below. Click the Add New button. In the Mode field, select IP Address or MAC Address. If you select IP Address, please follow the steps below: ...
Page 115: Schedule
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide In IP Address field, enter the IP address. If you select MAC Address, the screen shown is Figure 4-104. Figure 4-104 In Description field, create a unique description for the host (e.g. Host_1).
Page 116: Ipv6 Firewall
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Edit: Here you can modify an existing schedule.  To add a new schedule, follow the steps below: 1. Click Add New button and the next screen will pop-up as shown in Figure 4-107.
Page 117: Ipv6 Rule
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.17.1 IPv6 Rule Choose menu “IPv6 Firewall” → “IPv6 Rule”, and then you can view and set Access Control rules in the screen as shown in Figure 4-108. Figure 4-108 ...
Page 118: Ipv6 Lan Host
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Select a host from the IPv6 LAN Host drop-down list or choose “Add IPv6 LAN Host”. Select a target from the IPv6 WAN Host drop-sown list or choose “Add IPv6 WAN Host”.
Page 119: Ipv6 Wan Host
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Click the Save button to save the settings. Click the Delete Selected button to delete selected entries. 4.17.3 IPv6 WAN Host Choose menu “IPv6 Firewall” → “IPv6 WAN Host”, and then you can view and set a Host list in the screen as shown in Figure 4-112.
Page 120: Ipv6 Tunnel
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-114 Description: Here displays the description of the schedule and this description is unique.  Edit: Here you can modify an existing schedule.  To add a new schedule, follow the steps below: Click Add New button and you will see the screen as shown in Figure 4-115.
Page 121 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide IPv6 completely supplants IPv4. It is a temporary solution for networks that do not support native dual-stack, where both IPv6 and IPv4 run independently. Choose menu “IPv6 Tunnel”, and you will see the screen as shown in Figure 4-116.
Page 122 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-118 WAN Connection: Select a WAN connection from the drop-down list. Only the connected  WAN connections can be shown in the drop-down list. Configuration Type: Select a configuration type for this tunnel. Auto means to obtain the ...
Page 123: Bandwidth Control
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.19 Bandwidth Control Choose menu “Bandwidth Control”, and then you can configure the Upstream Bandwidth and Downstream Bandwidth in the next screen. The values you configure should be less than 1000000Kbps.
Page 124: Ip & Mac Binding
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-121 Click the Save button. Click the Enable/ Disable Selected button to make selected entries enabled or disabled. Click the Delete Selected button to delete selected entries. 4.20 IP & MAC Binding There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List.
Page 125: Arp List
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Edit: To modify or delete an existing entry.  When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Edit button, and then you will go to the next page.
Page 126: Dynamic Dns
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Click the Load Selected button to load selected items to the IP & MAC Binding list. Click the Refresh button to refresh all items. 4.21 Dynamic DNS Choose menu “Dynamic DNS”, and you can configure the Dynamic DNS function.
Page 127: System Tools
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-126 4.23 System Tools Choose menu “System Tools”, and you can see the submenus under the main menu: System Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore, Factory Defaults, Firmware Upgrade, Reboot and Statistics.
Page 128: Time Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-127 Log Type: By selecting the log type, only logs of this type will be shown.  Log Level: By selecting the log level, only logs of this level will be shown.
Page 129: Manage Control
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-129 Time Zone: Select your local time zone from this pull down list.  Date: Enter your local date in MM/DD/YY into the right blanks.  Time: Enter your local time in HH/MM/SS into the right blanks.
Page 130: Cwmp Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-130 Current User Status: This box displays the information about User Type, User Name, Host  IP Address and Host MAC Address. Account Management: Here you can set the account user information about Old Password, ...
Page 131: Snmp Settings
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-131 CWMP: Select enable the CWMP function.  Inform: Enable or disable the function. If enabled, the information will be informed to ACS  server periodically. Inform Interval: Enter the interval time here.
Page 132: Backup & Restore
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-132 An SNMP Agent is an application running on the modem router that performs the operational role of receiving and processing SNMP messages, sending responses to the SNMP manager, and sending traps when an event occurs.
Page 133: Firmware Upgrade
To upgrade the modem router's firmware, follow these instructions below: Download a most recent firmware upgrade file from our website (www.tp-link.com). Enter or select the path name where you save the downloaded file on the computer into the File Name blank.
Page 134: Reboot
 Note: New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the modem router rather than the configuration, you can try to upgrade the firmware.
Page 135 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Figure 4-137 Traffic Statistics: Enable or Disable. The default value is disabled. To enable it, click Enable.  If it is disabled, the function of DoS protection in Security settings will be disabled.
Page 136: Logout
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide 4.24 Logout Choose “Logout”, and you will back to the login screen as shown in Figure 4-138. Figure 4-138...
Page 137: Appendix A: Specifications
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Appendix A: Specifications General IEEE 802.3, 802.3u, IEEE 802.11b, 802.11g, 802.11n ITU-T G.993.2, ITU-T G.992.5, ITU-T G.992.3 (G.dmt.bis), ITU-T G.992.4 (G.lite.bis) Full-rate ANSI T1.413 Issue 2, ITU-T G.992.1(G.DMT), ITU-T Standards and Protocols G.992.2(G.Lite), ITU-T G.994.1 (G.hs), ITU-T G.995.1...
Page 138: Appendix B: Troubleshooting
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my modem router’s configuration to its factory default settings? With the modem router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it.
Page 139 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Select Obtain an IP address automatically and Obtain DNS server address automatically.  Then click OK. For Windows 8 Move your mouse to the lower right corner and you will see Search icon in the Popups.
Page 140 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Now, try to log on to the Web-based management page again after the above settings have been configured. If you still cannot access the configuration page, please restore your modem router’s factory default settings and reconfigure your modem router following the instructions in 3.2 Quick...
Page 141 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide d) Then the configuration wizard will pop up and show you how to connect your devices. After that, the Easy Setup Assistant will start. Click NEXT, and then follow the step-by-step instructions.
Page 142 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide f) Follow the step-by-step instructions until you comes to the finish screen. Click FINISH to close this wizard. g) The configure files can be found in your USB device which means you have successfully...
Page 143 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide...
Page 144: Appendix C: Telephony Features
TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Appendix C: Telephony Features This section introduces what the following features are used for. Call Holding This feature allows you to put a call on hold, in which case the call is not ended but no verbal communication is available.
Page 145 TD-VG5612 300Mbps Wireless N VoIP VDSL/ADSL Modem Router User Guide Speed Dial This feature allows you to create short numbers for your frequently used telephone numbers to make your dialing more convenient. You just need to press one or two digits and the key # instead of the original phone number to make a call.

TP-Link TD-VG5612 User Manual

Package Contents

Chapter 1. Product Overview

Chapter 2. Connecting the Modem Router

Chapter 3. Quick Installation Guide

Chapter 4. Configuring the Modem Router

Appendix A: Specifications

Appendix B: Troubleshooting

Appendix C: Telephony Features

Quick Links

Related Manuals for TP-Link TD-VG5612

Summary of Contents for TP-Link TD-VG5612

Table of Contents