Summary of Contents for ADS-tec IWL3000 series
-
Page 1: User Manual
Version 2.0 Effective as of 10/14 Translation of original instruction manual User Manual IT Infrastructure IWL3000 series... -
Page 2: Table Of Contents
Treatment and disposal of lithium batteries 3.10 Safety instructions 4 Introduction 3.1 Equipment versions Scope of delivery Environmental conditions 5 Assembly Overall device dimensions Mounting options 5.2.1 Table mounting 5.2.2 Wall mounting 5.2.3 Top-hat rail mounting © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 3 Calling up the device web interface 8 Certifications Channel list ETSI 2.4 GHz Channel list ETSI 5 GHz, IEEE 802.11 a/h, n 9 Technical details 10 Service & support 10.1 ads-tec support 10.2 Company address © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 4: Note
German instruction manual. 1.2 Limitation of liability ads-tec GmbH shall not be liable for personal injury, property damage or damage caused to the product as well as consequential damage that is/was the result of non-compliance with this instruction manual,... -
Page 5: Safety Instructions
The symbol "Recommendation for use" indicates terms and/or conditions that strictly need to be observed to ensure optimised and/or zero-defect operation. Tips and suggestions for the efficient use of the device and software optimisation are also provided. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 6: Symbols
StoraXe® and Big-LinX® are registered trademarks of ads-tec. All other third-party trademarks used are hereby acknowledged. In the case of infringement of trademark rights, ads-tec reserves the right to exercise all rights. 2.7 Copyright This instruction manual is protected by copyright. For the authorised user, simple usage rights are granted within the scope of the intent of the contract. -
Page 7: Standards
It is therefore necessary to employ BUS and LAN cables with shielded connectors and these must be installed as per the instructions contained in the instruction manual. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 8: Settings For Use With Internet Explorer
Recommendation for use: Only the original ads-tec firmware / software is allowed for any of the settings and features described in this instruction manual. Loading of any firmware / software that has not been released by ads-tec invalidates the warranty. -
Page 9: Safety Instructions
To avoid overheating in operation: The device must not be exposed to direct radiation by sunlight or any other light or heat source. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 10: Damage Due To Improper Use
•The devices do not have a deterministic system behaviour •No MIN/MAX roaming time can be guaranteed The setting of the applicable regulatory authority and the antenna gain is the responsibility of the operating company. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 11: Intended Use
In the case of improper use, ads-tec shall not accept responsibility or liability for injury or damage that is directly or indirectly attributable to the handling of the device. -
Page 12: Safety Instructions
Recommendation for use: Always adhere to the safety measures applicable when handling components at risk of being damaged by electrostatic discharges. The provisions of DIN EN 61340-5-1 / DIN EN 61340-5-2 apply © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 13: Introduction
With this tool you can, for example, define individual parameters or whole groups of parameters on a master device and transfer them to a limited selection or to all ads-tec devices of same design and version without having to make these time-consuming configurations on each individual device. -
Page 14: Scope Of Delivery
4 x rubber feet 1 x Ethernet cable, 1m red 1 x Quick Start-Up Guide / Quick Assembly Guide 1 x GNU General Public License © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 15: Environmental Conditions
4.2 Environmental conditions The device can be put into operation and used under the following conditions. Failure to observe any one of these conditions will invalidate the warranty. ads-tec cannot be held liable for any damages arising from improper use and handling. -
Page 16: Assembly
IWL3000 series 5 Assembly 5.1 Overall device dimensions Fig. 1: © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 17: Mounting Options
Alternatively, the device can be mounted according to the VESA 75 standard on a suitable mounting surface. Fig. 2: Information: For mounting, use M4 screws of a suitable length. The usable blind hole depth of the mounting holes is 6mm. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 18: Top-Hat Rail Mounting
(2). The device must be felt to snap into the rail. Fig. 3: To release the device from the DIN rail, proceed in reverse order. Information: Make sure not to damage the mounting rail of the unit when removing it.. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 19: System Features
The device is supplied with voltage via POWER and is ready for operation Status (1) This device is not supplied with voltage Error during the boot-up process / recovery image © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 20 IWL3000 series Abb. 5: Link (2) / (3) Signal Action There is no Wi-Fi connection active Search for available WLAN networks Connection established Activity (2) / (3) Active traffic © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 21: Operational Led Status Indicators
6.2.3 Behaviour of the status indicators during a firmware update A firmware update can be performed via the web interface. The actual update process may require a few minutes. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 22: Interface Overview
The device is equipped with the following interfaces (rear/side): Fig. 7: 8. WLAN antenna (WLAN module 1) 9. SCM card reader (read in/out the ads-tec SIM cards) 10. WLAN antenna (WLAN module 2) Information: All input voltages can be connected redundantly... -
Page 23: Dc Power Supply
24V DC Technical data of the power adapter • Input voltage: 7 - 36V DC 6.3.2 LAN 1 (RJ45) PIN number Signal name TX + TX - RX + RX - © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 24: Lan 2 (Rj45)
IWL3000 series 6.3.3 LAN 2 (RJ45) PIN number Signal name TX + TX - RX + RX - © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 25: Usb Connections
6.3.5 X2 Pin-Nummer Signal-Name 24V DC 6.3.6 USB CONNECTIONS The USB interfaces are used for connecting peripherals with USB connection. The interface complies with the USB 2.0 standard. PIN number Signal name © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 26: Sim Card Reader In Accordance With Iso 7816
IWL3000 series 6.3.7 SIM CARD READER IN ACCORDANCE WITH ISO 7816 The SIM card reader is used to store configuration data. PIN number Signal name VCC 5 volt RESET CLOCK © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 27: Placing Into Operation
When placing into operation for the first time, a connection is required between the device and a PC via an RJ45 network cable. Connect the device to a PC: Device LAN connection <-> PC LAN connection © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 28: Manual Configuration Of The Network Adapter
Access to the device is only enabled if the following parameters are entered as the fixed IP address or if the computer is located in the same subnet space: IP ADDRESS: 192.168.0.100 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 29 Once the IP address has been entered, the subnet mask address must be entered. Click on the Subnet mask field and the correct address is entered automatically. Subnet mask: 255.255.255.0 The dialogue tab can now be closed with "OK". © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 30: Settings For Use With Internet Explorer 8
In the Add this website to the zone address line, enter the device IP address and confirm with Add. Default IP address: http://192.168.0.254 The IP address should now appear in the list under Websites. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 31 IWL3000 series Fig. 11: © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 32: Calling Up The Device Web Interface
Often, local subnet addresses (e.g. 192.168.x.x) are also diverted to a proxy server. In this case, it is possible to select the "Bypass proxy server for local addresses" option to enter the address in question. © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 33 IWL3000 series The device web interface then appears. Fig. 13: © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 34: Certifications
2.462 2.467 2.472 Information: TPC can optionally be activated at 2.4 GHz 13 channels, each 22 MHz wide 2 to 3 interference free channels in 802.11n operation with 40MHz channel bandwidth © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... - Page 35 IWL3000 series Achtung: TPC is always active at 5 GHz 19 channels, each 22 MHz wide © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen...
-
Page 36: Channel List Etsi 5 Ghz, Ieee 802.11 A/H, N
108+ 5,540 1.000 1.000 5,560 1.000 1.000 116+ 5,580 1.000 1.000 5,600 1.000 1.000 124+ 5,620 1.000 1.000 5,640 1.000 1.000 132+ 5,660 1.000 1.000 5,680 1.000 1.000 5,700 1.000 1.000 © ads-tec GmbH • Heinrich-Hertz-Str. 1 • D-72622 Nürtingen... -
Page 37: Technical Details
9 Technical details Device data IWL3000 series Operating system Embedded LinuX Configuration protocol http, https Power supply 24V DC +/- 20%, redundant voltage input Interfaces IN/OUT (electrically isolated) 1 x LAN RJ45 connection 10/100/1000MBit/s Auto crossover 1 x LAN RJ45 connection... -
Page 38: Service & Support
In this case, maintenance and support is provided by the partner company.