SERVICE MANUAL HW80-B1486/HW80-B1286 Contents Chapter 1 General Information ________________________________________________ 1-1. General Guidelines_____________________________________________________ 1-2. Function indication symbols ______________________________________________ Chapter 2 Product Feature _________________________________________________ 2-1. Features __________________________________________________________ 2-2. Specification _______________________________________________________ Chapter 3 Appearance brief introduction _____________________________________ 3-1. Name of parts ______________________________________________________ 3-2. Net dimension______________________________________________________...
HW80-B1486/HW80-B1286 (You will see them in the program introduction table) Signify the program has this course. Signify the program doesn t havet his course. Front Load Washing Machine...
SE RVICE MANUAL HW80-B1486/HW80-B1286 Chapter 2 Product Feature 2-1. Features Power-down memory With the power-down memory function, the washer can memorize the program s ru nning state in case of power failure or loose plug during washing and continue the selected program after resuming the power supply.
SERVICE MANUAL HW80-B1486/HW80-B1286 Chapter 5 Wiring circuit Lumbe g:3641 05 Filt er + 12V Pow er + 5V Heater Door lock B86 Board Washer RAST5.0 Drain _ Pump edge connector Di spl ay Main_Valve Pre _ Valve Hot _ Valve...
SERVICE MANUAL HW80-B1486/HW80-B1286 6-2 Self check 1. How to start Press the "Intense" and Pr ewas but ton, the np l ug on the m a ch i ne," tESt"will be displayed by tur Press Start/Pause but ton , the mod e l of the machine wi l l be displayed( suchas 14 80).Pres Start/Pause button again,the machine will start a self test program, then the following will be performed.
SERVICE MANUAL HW80-B1486/HW80-B1286 Chapter 7 Error Display and troubleshooting Front load Washing Machine...
Page 15
The wire connected PCB and inlet valve is not Check if export voltage from PCB to properly. Please reconnect it or replace it. electromagnetic valve (between X3-1 and X3-7), is it between AC 220-240V? Replace PCB Haier Front Load Washing Machine...
Switch on the power and look if the light on the motor flash every 0.5 seconds Switch on the power and look if the light on the PCB flash every 0.5 seconds Replace Haier Front Load Washing Machine...
Switch on the power and check if the export voltage from PCB to water level sensor is not 5V? Error message: The PBC and the motor cant’t communicate. Tr oubleshoo ting: Contact the maintenance personnel. Haier Front Load Washing Machine...
Replace electromagnetic valve there open circuit between electromagnetic valve and PCB? Reconnect the wire Choose pre-wash program and start, Replace PCB then check if there is 220-240V at export pin of electromagnetic valve Haier Front Load Washing Machine...
If it is broken, replace it. Replace motor Turn on power and set spin program, then start, check if there is different noise from motor Haier Front Load Washing Machine...
Is water leaking from outer cylinder? 7-4. Parameter of primary electronic appliance The rated voltage , current and frequency of motor The rated voltage of motor is 200~240V,rated current of motor is 6A,rated frequency of motor is 50/60Hz, Heater Haier Front Load Washing Machine...
SERVICE MANUAL HW80-B1486/HW80-B1286 Front Load Washing Machine...
Page 22
SERVICE MANUAL HW80-B1486/HW80-B1286 Front Load Washing Machine...
Page 23
SERVICE MANUAL HW80-B1486/HW80-B1286 Dismantle the motor Release the two screws on the Motor bracket. Pull the motor along the arrowhead, then take off the motor. Dismantle shock absorber shock absorber Pull out the pin of shock absorber, then take of f the bolt and washer of on the cabinet The pins can not be used again.
Page 24
SERVICE MANUAL HW80-B1486/HW80-B1286 Front Load Washing Machine...
Page 25
SERVICE MANUL HW80-B1486/HW80-B1286 Haier Group Haier I ndus trial Pa rk , No.1, Haie r Roa d 266101 , Qingdao, Chin a http://www.haier.com Front Load Washing Machine...