Why is my Haier HW80-B14979 washing machine not draining water?

Your washing machine may not be draining water due to several reasons:The drain hose is blocked or its end is higher than 100 cm above floor level. The height of the drain pipe should be adjusted to 80-100 cm.The pump filter is blocked or jammed.The hose-connecting cylinder to the pump is bent or jammed.There might be a drainage error where water is not emptied within 4 minutes.Issues with the drain pump, such as it being jammed, not working correctly (e.g., incorrect electric resistance), or having an incorrect import voltage.Problems with wire connections to the pump, drain valve, or between the drain pump and PCB.The pipe connected to the water level sensor might be jammed.A PCB issue.To resolve these: Unblock the drain hose and clean the pump filter. Adjust the height of the drain pipe to 80-100 cm. Clean the filter and tighten it clockwise. Arrange the hose and clean if the connecting cylinder is bent or jammed. If the drain pump is faulty, replace the drain pump. Reconnect the wire properly or replace it if the connection between the drain pump and PCB is open. If the pipe connected to the water level sensor is jammed, clean it.

Why is my Haier HW80-B14979 washing machine leaking water?

Your washing machine may be leaking water due to:Water leaking from the inlet pipe or the tap.A broken drain pipe.Foreign material caught between the cushion of the sight window and the sight window.Leaking tubes and tie-ins, including connections of the tube and valve, dispenser, outer cylinder-cushion of sight window-hose, and outer cylinder, or drain.A broken cushion of the sight window.Water leaking from the outer cylinder.To resolve these issues: Readjust the inlet pipe or tap. Replace the drain pipe if it is broken. Remove clothes if foreign material is causing the leak. Reassemble or repair any leaking tubes and tie-ins. Replace the cushion if the sight window cushion is broken. Replace the outer cylinder if water is leaking from it. For more information, see pages 29 and 32 of the manual.

Why does my Haier HW80-B14979 washing machine shake or move during spin cycles?

Your washing machine may shake or move during spin cycles due to:Transportation bolts that have not been fully removed.The appliance not being on solid ground or in a levelled position.An incorrect machine load or unbalanced laundry. To address these issues:Remove all transportation bolts.Ensure the appliance is on solid ground and in a levelled position by adjusting the adjustable feet.Check the load weight and balance. If laundry is unbalanced, check the machine load and laundry and run a spinning programme again. For more information, see pages 21, 22 and 31 of the manual.

Why is my Haier HW80-B14979 washing machine not spinning clothes dry?

Your washing machine may not be spinning clothes dry due to:Unbalanced laundry. In this case, check the machine load and laundry and run a spinning programme again.Unbalance protection being active because the load is too little. If this occurs, increase the loading.

Why won't my Haier HW80-B14979 washing machine turn on?

Your washing machine may not turn on due to several reasons:The programme may not be started.The door may not be properly closed.The appliance may not be switched on.There might be a power failure or no 220V-240V AC voltage power supply.The child lock or time delay function might be activated.The pause button might be pressed.The power switch may not be on.A filter might be broken.Plugs may not be connected well.The PCB might be broken.To resolve these: Check the programme and start it. Close the door properly. Switch the appliance on and check the power supply. Deactivate the child lock, time delay function, or pause mode. Press the power switch. Replace the filter if broken. Insert the plugs well and test. Replace the PCB if it is broken.

How do I drain water from my Haier HW80-B14979 washing machine?

To drain water from your washing machine, especially if it's not draining automatically:Locate the filter door.Open the filter door.Squeeze the plastic plugs out of the water flow and pull a plastic block to allow residual water inside the washing machine to drain.Once the water has drained, you can rotate the filter counterclockwise to remove it and clean it. For more information, see page 39 of the manual.

How do I clean the filter on my Haier HW80-B14979 washing machine?

To clean the filter:Open the filter door.Squeeze the plastic plugs out of the water flow and pull a plastic block to drain any residual water from the washing machine.Rotate the filter counterclockwise to remove it.Clean the pump filter or filter trap.

Why is my Haier HW80-B14979 washing machine making excessive noise?

Excessive noise can be caused by several factors:Transportation bolts may not have been fully removed.The appliance may not be on solid ground or in a levelled position.The machine load may not be correct or the laundry may be unbalanced.Foreign objects like coins or zippers might be hitting the drum. Ensure pockets are emptied.There might be pack screws that need to be dismantled, or other foreign material inside the washer that needs to be cleaned.The washer might not be in balance, requiring adjustment of the adjustable feet.A loose or worn bolt may need to be replaced.Components like the shock absorber, bearing, or rotor might be broken and require replacement.The motor might be making a different noise, indicating it needs replacement.

How do I start a wash cycle on the Haier HW80-B14979 washer?

To start a wash cycle, check and select your desired programme, then touch the start button. For more information, see page 21 of the manual.

Why is my Haier HW80-B14979 washing machine not rinsing clothes properly?

If your washing machine is not rinsing clothes properly, resulting in residues:Insoluble detergent particles might be leaving white spots. You can perform an extra rinse, brush the points from the dry laundry, or choose another detergent.Fats, oils, creams, or ointments might be causing grey patches. In this case, pretreat the laundry with a special cleaner. For more information, see page 22 of the manual.

How do I fix an 'FA' error code on my Haier HW80-B14979 washing machine?

To fix an 'FA' error code, which indicates a water level sensor error:Check if the wire connection to the water level sensor is loose and fix it. Ensure the line of the water level sensor is connected well.Ensure the line of the PCB is connected well.If the problem persists, change the water level sensor.If the export voltage from the PCB to the water level sensor is not 5V, you may need to change the PCB.

What do error codes on the Haier HW80-B14979 washing machine mean?

The error codes on the Haier HW80-B14979 washing machine indicate the following issues:CLR FLTR: Drainage error where water is not emptied within 4 minutes.E2: An unlocking or locking error, specifically indicating the door lock is not closed.F3: A water temperature sensor error, meaning the temperature sensor is not properly connected or damaged.E4: A water inlet error, indicating the required water level is not reached within 8 minutes.F4: A heating system error, suggesting the heater may be broken.F7: A motor system error, meaning the motor is not rotated.E8: Water level in the drum is too high, indicating water level exceeds protection value.FA: A water level sensor error, specifically that the water level sensor is unnormal.FC0: A communication bus error, indicating PCB abnormal phenomena.FC1: A motor driving module communicating error, indicating a connecting issue between the control board and driven boards.FC2: A motor driving module communicating error, indicating a connecting issue between the control board and power boards.Fb: A sub-switch continuously leaks for 10 seconds error, indicating water overflow.UNB: Indicates that the distribution of laundry is unbalanced during spinning.

How do I clean the detergent dispenser drawer on my Haier HW80-B14979?

To clean the detergent dispenser drawer:Press the siphon cover with your forefinger.Pull out the soap dispenser. Once removed, you can clean it. For more information, see page 37 of the manual.

What should I do if the Haier HW80-B14979 washing machine loses power during a cycle?

If your washing machine loses power during a cycle, you should check the power supply and check the power and water supply. For more information, see page 21 of the manual.

How do I stop a wash cycle on the Haier HW80-B14979 mid-cycle?

To stop a wash cycle mid-cycle, you can deactivate pause mode if the cycle is paused. To cancel a program, you may need to cancel the programme and restart. For more information, see page 21 of the manual.

Haier HW80-B14979 Service Manual

Front load washing machine

Hide thumbs Also See for HW80-B14979:

User manual

User manual (68 pages)

User manual (68 pages)

page of 42

/ 42
FAQs
Bookmarks

Quick Links

Download this manual
Frequently Asked Questions (15)

Front Load Washing Machine

Model:HW80-B14979

HW100-B14979

HW120-B14979

Why is my Haier HW80-B14979 washing machine not draining water?
Your washing machine may not be draining water due to several reasons:
- The drain hose is blocked or its end is higher than 100 cm above floor level. The height of the drain pipe should be adjusted to 80-100 cm.
- The pump filter is blocked or jammed.
- The hose-connecting cylinder to the pump is bent or jammed.
- There might be a drainage error where water is not emptied within 4 minutes.
- Issues with the drain pump, such as it being jammed, not working correctly (e.g., incorrect electric resistance), or having an incorrect import voltage.
- Problems with wire connections to the pump, drain valve, or between the drain pump and PCB.
- The pipe connected to the water level sensor might be jammed.
- A PCB issue.
To resolve these:
- Unblock the drain hose and clean the pump filter.
- Adjust the height of the drain pipe to 80-100 cm.
- Clean the filter and tighten it clockwise.
- Arrange the hose and clean if the connecting cylinder is bent or jammed.
- If the drain pump is faulty, replace the drain pump.
- Reconnect the wire properly or replace it if the connection between the drain pump and PCB is open.
- If the pipe connected to the water level sensor is jammed, clean it.
Was this helpful?
Why is my Haier HW80-B14979 washing machine leaking water?
Your washing machine may be leaking water due to:
- Water leaking from the inlet pipe or the tap.
- A broken drain pipe.
- Foreign material caught between the cushion of the sight window and the sight window.
- Leaking tubes and tie-ins, including connections of the tube and valve, dispenser, outer cylinder-cushion of sight window-hose, and outer cylinder, or drain.
- A broken cushion of the sight window.
- Water leaking from the outer cylinder.
To resolve these issues:
- Readjust the inlet pipe or tap.
- Replace the drain pipe if it is broken.
- Remove clothes if foreign material is causing the leak.
- Reassemble or repair any leaking tubes and tie-ins.
- Replace the cushion if the sight window cushion is broken.
- Replace the outer cylinder if water is leaking from it.
For more information, see pages 29 and 32 of the manual.
Was this helpful?
Why does my Haier HW80-B14979 washing machine shake or move during spin cycles?
Your washing machine may shake or move during spin cycles due to:
- Transportation bolts that have not been fully removed.
- The appliance not being on solid ground or in a levelled position.
- An incorrect machine load or unbalanced laundry. To address these issues:
- Remove all transportation bolts.
- Ensure the appliance is on solid ground and in a levelled position by adjusting the adjustable feet.
- Check the load weight and balance. If laundry is unbalanced, check the machine load and laundry and run a spinning programme again.
For more information, see pages 21, 22 and 31 of the manual.
Was this helpful?
Why is my Haier HW80-B14979 washing machine not spinning clothes dry?
Your washing machine may not be spinning clothes dry due to:
- Unbalanced laundry. In this case, check the machine load and laundry and run a spinning programme again.
- Unbalance protection being active because the load is too little. If this occurs, increase the loading.
Was this helpful?
Why won't my Haier HW80-B14979 washing machine turn on?
Your washing machine may not turn on due to several reasons:
- The programme may not be started.
- The door may not be properly closed.
- The appliance may not be switched on.
- There might be a power failure or no 220V-240V AC voltage power supply.
- The child lock or time delay function might be activated.
- The pause button might be pressed.
- The power switch may not be on.
- A filter might be broken.
- Plugs may not be connected well.
- The PCB might be broken.
To resolve these:
- Check the programme and start it.
- Close the door properly.
- Switch the appliance on and check the power supply.
- Deactivate the child lock, time delay function, or pause mode.
- Press the power switch.
- Replace the filter if broken.
- Insert the plugs well and test.
- Replace the PCB if it is broken.
Was this helpful?
How do I drain water from my Haier HW80-B14979 washing machine?
To drain water from your washing machine, especially if it's not draining automatically:
1. Locate the filter door.
2. Open the filter door.
3. Squeeze the plastic plugs out of the water flow and pull a plastic block to allow residual water inside the washing machine to drain.
4. Once the water has drained, you can rotate the filter counterclockwise to remove it and clean it.
For more information, see page 39 of the manual.
Was this helpful?
How do I clean the filter on my Haier HW80-B14979 washing machine?
To clean the filter:
1. Open the filter door.
2. Squeeze the plastic plugs out of the water flow and pull a plastic block to drain any residual water from the washing machine.
3. Rotate the filter counterclockwise to remove it.
4. Clean the pump filter or filter trap.
Was this helpful?
Why is my Haier HW80-B14979 washing machine making excessive noise?
Excessive noise can be caused by several factors:
- Transportation bolts may not have been fully removed.
- The appliance may not be on solid ground or in a levelled position.
- The machine load may not be correct or the laundry may be unbalanced.
- Foreign objects like coins or zippers might be hitting the drum. Ensure pockets are emptied.
- There might be pack screws that need to be dismantled, or other foreign material inside the washer that needs to be cleaned.
- The washer might not be in balance, requiring adjustment of the adjustable feet.
- A loose or worn bolt may need to be replaced.
- Components like the shock absorber, bearing, or rotor might be broken and require replacement.
- The motor might be making a different noise, indicating it needs replacement.
Was this helpful?
How do I start a wash cycle on the Haier HW80-B14979 washer?

To start a wash cycle, check and select your desired programme, then touch the start button.

For more information, see page 21 of the manual.

Was this helpful?
Why is my Haier HW80-B14979 washing machine not rinsing clothes properly?
If your washing machine is not rinsing clothes properly, resulting in residues:
- Insoluble detergent particles might be leaving white spots. You can perform an extra rinse, brush the points from the dry laundry, or choose another detergent.
- Fats, oils, creams, or ointments might be causing grey patches. In this case, pretreat the laundry with a special cleaner.
For more information, see page 22 of the manual.
Was this helpful?
How do I fix an 'FA' error code on my Haier HW80-B14979 washing machine?
To fix an 'FA' error code, which indicates a water level sensor error:
1. Check if the wire connection to the water level sensor is loose and fix it. Ensure the line of the water level sensor is connected well.
2. Ensure the line of the PCB is connected well.
3. If the problem persists, change the water level sensor.
4. If the export voltage from the PCB to the water level sensor is not 5V, you may need to change the PCB.
Was this helpful?
What do error codes on the Haier HW80-B14979 washing machine mean?
The error codes on the Haier HW80-B14979 washing machine indicate the following issues:
- CLR FLTR: Drainage error where water is not emptied within 4 minutes.
- E2: An unlocking or locking error, specifically indicating the door lock is not closed.
- F3: A water temperature sensor error, meaning the temperature sensor is not properly connected or damaged.
- E4: A water inlet error, indicating the required water level is not reached within 8 minutes.
- F4: A heating system error, suggesting the heater may be broken.
- F7: A motor system error, meaning the motor is not rotated.
- E8: Water level in the drum is too high, indicating water level exceeds protection value.
- FA: A water level sensor error, specifically that the water level sensor is unnormal.
- FC0: A communication bus error, indicating PCB abnormal phenomena.
- FC1: A motor driving module communicating error, indicating a connecting issue between the control board and driven boards.
- FC2: A motor driving module communicating error, indicating a connecting issue between the control board and power boards.
- Fb: A sub-switch continuously leaks for 10 seconds error, indicating water overflow.
- UNB: Indicates that the distribution of laundry is unbalanced during spinning.
Was this helpful?
How do I clean the detergent dispenser drawer on my Haier HW80-B14979?
To clean the detergent dispenser drawer:
1. Press the siphon cover with your forefinger.
2. Pull out the soap dispenser. Once removed, you can clean it.
For more information, see page 37 of the manual.
Was this helpful?
What should I do if the Haier HW80-B14979 washing machine loses power during a cycle?

If your washing machine loses power during a cycle, you should check the power supply and check the power and water supply.

For more information, see page 21 of the manual.

Was this helpful?
How do I stop a wash cycle on the Haier HW80-B14979 mid-cycle?

To stop a wash cycle mid-cycle, you can deactivate pause mode if the cycle is paused. To cancel a program, you may need to cancel the programme and restart.

For more information, see page 21 of the manual.

Was this helpful?

Need help?

Do you have a question about the HW80-B14979 and is the answer not in the manual?

Questions and answers

Summary of Contents for Haier HW80-B14979

Page 1 Front Load Washing Machine Model:HW80-B14979 HW100-B14979 HW120-B14979...
Page 4 80:Max Wash Load-8kg 100:Max Wash Load-10kg 120:Max Wash Load-12kg...
Page 5 ● DD motor...
Page 6 HW80- HW100- HW120- B14979 B14979 B14979 220-240V/50Hz 1400 1800 850x460x595 850x530x595 850x600x595 72/77 77/82 80/86 0.42 0.42 0.48 0.50 0.50 0.58...
Page 7 ● ● ● ● ●...
Page 8 ● ● ● ● ●...
Page 9 Delay Temp. Stain removal Steam Extra Rinse Speed Synthetics Cotton Duvet Wool Delicate Outdoor Refresh Babycare Express 15’ Fast Spin Cotton 20 Eco 40-60 1 “Power” button Display Function buttons Detergent /Softener drawer 6 “Start/Pause“ button Programme selector Note : Acoustic signal In following cases, an acoustic signal is no sounds by default: when pressing a button at the end of programme...
Page 10 3.4 Detergent drawer Open dispenser drawer,the following components can be seen (Fig. 4-5): 1: compartment for powder or liquid detergent. 2: detergent ﬂap slector, lift it up for powder detergent, keep it down for liquid detergent. 3: compartment for sanitizer. 4: compartment for softner.
Page 11 4.5.4 Function button“Speed“ 4-10 Touch this button (Fig. 4-10) to change or deselect the Speed spin of the programme. If no value is illuminated the dis- play"0")the laundry will not spin. 4.5.5 “Extra Rinse ” button 4-11 Touch this button (Fig. 4-11) to rinse the laundry more intense with fresh water.
Page 12 • sanitizer Yes, Optional, º Max. load Temperature Preset Function spin speed in kg in °C in rpm HW80-B14979 selectable Programme HW100-B14979 range Fabrics type HW120-B14979 • • • • • • Cotton 8/10/12 * to 90 Cotton 1400 º...
Page 14 2.2.1 1 Worktop 2 Detergent / Softener / disin- 1 Power cord plug fectant drawer 3 Drum door 2 Work top 4 Front panel 3 Water inlet valve 5 Adjustable feet (4 in all) 4 Power cord Touch screen display 5 Back cover Power button 6 Back cover screw...
Page 15 HW80-B14979:(H*W*D)mm=(850*595*460)mm HW100-B14979:(H*W*D)mm=(850*595*530)mm ● HW120-B14979:(H*W*D)mm=(850*595*600)mm...
Page 19 Main Pre- Drai- wash wash nage valve valve pump...
Page 20 E80 0 will be displayed ,then touch "Star t /Pause",If the storage is successful, the screen will display "PASS" otherwise and "FAIL" wil l continue to display. Please power oﬀ. For modle HW80-B14979 ,we can choose E800 For modle HW100-B14979 ,we can choose EA00 For modle HW120-B14979 ,we can choose EC00...
Page 21: Error Display And Troubleshooting
10- Error Display and troubleshooting 10-1 Troubleshooting without display code Problem Cause Solution Appliance fails to • Programme is not yet started. • Check programme and start it. operate. • Door is not properly closed. • Close the door properly. •...
Page 22 Problem Cause Solution Strange sound • Appliance has no solid position. • Ensure solid ground and a lev- elled position. • Foreign m atters like coins or zip- • Ensure pockets are emptied of pers hit the drum. keys, coins etc. Parts of control •...
Page 23 Cause Solution code 1.Clean ﬁlter trap and check the drain hose for blockage. 2. Check pump and wire connection then ﬁx. Drainage error FLTR 3. Check drain valve and wire connection then ﬁx. Unlocking error Shut door properly. If problem is still exist, please check the door lock and wire connection then ﬁx.
Page 24 CLR FLTR Error mes s age: The door lock not closed. Front Load Washing Machine...
Page 25 Front Load Washing Machine...
Page 26 Error message:The required water level is not reached within 8 min. Check if the import voltage of electromagnetic valve is blocked by dirt. Clean it right now. Draw out the dispenser and check if Observe if the height of drain pipe not reach 80 water is entering cm.If water level sensor and the hose is leaking gas.
Page 27 Front Load Washing Machine...
Page 28 Error message:PCB Abnormal phenomena Check the PCB power lines and reactance lines Check the PCB power lines and ,make sure they are well inserted reactance lines,make sure they are well inserted. Check if the PCB communication lines are Make sure the communication lines are well connected properly inserted.
Page 29 Front Load Washing Machine...
Page 30 10-2 Front Load Washing Machine...
Page 31 Turn on power and set spin program, then start , check if there is different noise from moto r. Front Load Washing Machine...
Page 32 Front Load Washing Machine...
Page 33: Water Heater
10-3. 1.Water heater Heater voltage 230V 2.Drain pump Drain pump voltage 220-240V 50Hz Front Load Washing Machine...
Page 34: Water Inlet Valve
10-3. 3.Water inlet valve Door lock 4.Door lock a t l resistance 1-3: Front Load Washing Machine...
Page 35 10-3. Motor 5.Motor voltage 220V,50/60Hz resistance 5% 22 P171 Front Load Washing Machine...
Page 36: Chapter 11. Disassembly Guide
Chapter 11. Disassembly guide Attention: 1. Pull out the plug before disassembly. 2.Keep the wire away from sharp stuff,avoid any brokage of isoluation protector therefore avoid creepage. 3.Collect screws,accecoories and keep them in difference place,avoid missing parts so that the technicians could reassemble them. Picture Tools Screw driver...
Page 37 Dismantle the top cover 1.Dismantle the 2 fixing screws at each side of the top cove r. 2.Pull back the top cover and then take it off. Dismantle the soap dispensor 1.Press the siphon cover with your forefinger 2.Pull out the soap dispensor Front Load Washing Machine...
Page 38 Demolitia door assembly Demolitia of the front plate Front Load Washing Machine...
Page 39 Front Load Washing Machine...
Page 40 Dismantle the heater Dismantle drive plate Front Load Washing Machine...
Page 41 Dismantle Split heating pipe Dismantle counterweight Dismantle the water storage tank module Front Load Washing Machine...
Page 42 Sincere Forever Front Load Washing Machine...

This manual is also suitable for:

Hw100-b14979 Hw120-b14979

Haier HW80-B14979 Service Manual

Quick Links

Frequently Asked Questions (15)

Need help?

Questions and answers

Related Manuals for Haier HW80-B14979

Summary of Contents for Haier HW80-B14979

Page 21: Error Display And Troubleshooting

Page 33: Water Heater

Page 34: Water Inlet Valve

Page 36: Chapter 11. Disassembly Guide

This manual is also suitable for: