Pioneer DV-515 Service Manual page 10

DV-515
(9) Slider Out
1. Press [SCAN FWD] (10) key of the remote control unit in the
tracking off condition.
2. Turn the shuttle of the remote control unit in the FWD direction
(28 to 2A) in the tracking off condition. (DVD only)
(10) Scan In
1. Press [SCAN REV] (11) key of the remote control unit in the
tracking on condition.
2. Turn the shuttle of the remote control unit in the REV direction
(2C to 2F) in the tracking on condition.
• DVD can be scanned only in the case of the play 2 (playback
without demultiplex).
(11) Scan Out
1. Press [SCAN FWD] (10) key of the remote control unit in the
tracking on condition.
2. Turn the shuttle of the remote control unit in the FWD direction
(28 to 2A) in the tracking on condition.
• DVD can be scanned only in the case of the play 2 (playback
without demultiplex).
(12) Loading In/Out
When pressing [SKIP REV] (53) key of the remote control unit in
the open condition, it loads in the clamp direction. Then it loads in
the open direction when pressing [SKIP FWD] (52) key.
• This function can practice only when it is indicated with "OPEN"
in FL.
(13) Search Address Input Entry
It becomes the address input mode when [+10] (1F) key is pressed.
(indication for the most significant digit : > )
Indicate the last address as the initial condition in this time.
Only in case of DVD, addition search (indication for the most
significant digit : + ) and subtraction search (indication for the most
significant digit : – ) are able to select in order by pressing [+10]
key continuously.
The address where input value was added to the present address is
make to search with addition search.
The address where input value was subtracted to the present address
is make to search with subtraction search.
In case of CD is only absolute time search.
Also address clear and release from the address input mode are able
to perform by 2 steps by pressing [CLEAR] (45) key.
(14) Search Address Input
Press [0] to [9] keys of the remote control unit.
Set up the address by the hexadecimal number with DVD.
When [PROGRAM] (4C) key is pressed in the address input mode,
input mode changes to hexadecimal number input (Indicates "∗"
mark), and [1] to [6] keys are input as [A] to [F].
At this time, [7], [8], [9] and [0] keys are not accepted.
Also the hexadecimal number input and the decimal number input
can be changed with toggle.
(15) Search Practice
1. Press [CHP/TIM] (13) key of the remote control unit.
Practice the on screen no playback (Doesn't demultiplex) after
the search with DVD.
10
2. Press [PLAY] (17) key of the remote control unit.
Practice the on screen playback (demultiplex exists) after the
search with DVD.
(16) Auto Digital On/Off
Auto Digital ON/OFF switches every time [DIG/ANA] (0C) key of
the remote control unit is pressed.
(17) Screen Display On
1. Press [DISPLAY] (43) key of the remote control unit.
2. Display on/off switches every time [PROGRAM] (4C) key of the
remote control unit is pressed.
• When [DISPLAY] key is pressed in the display on, change the
part number indication of the microprocessor and revision
indication.
• Initial state is screen display on and it becomes the part number
indication of the microprocessor.
(18) Screen Display Off
1. Press [AUDIO] (1E) key of the remote control unit.
2. Display on/off switches every time [PROGRAM] (4C) key of the
remote control unit is pressed.
(19) Focus Jump +
Focus jumps in 1 layer from 0 layer when [MULTI FWD] (58) key
of the remote control unit is pressed. (DVD only)
(20) Focus Jump –
Focus jumps in 0 layer from 1 layer when [MULTI REV] (55) key
of the remote control unit is pressed. (DVD only)
2.4.2 EXPANSION FUNCTION 1
Set the reception mode of expansion function by pressing [TEST]
(5E) key of the LD test mode remote control unit, then expansion
function is able to execute by pressing the following keys.
Indication for the most significant digit becomes "T" during the
reception mode of expansion function. (This mode can on and off
with toggle.)
(1) LD On (650n)
Turn the laser diode to on by pressing [TEST] and [1] keys in order.
(2) Focus On
Focus locks by pressing [TEST] and [2] keys in order.
(3) Focus Sweep
Repeat focus sweep by pressing [TEST] and [3] keys in order.
(4) LD On (780n)
Turn the laser diode to on by pressing [TEST] and [4] keys in order.
(5) Spindle FG Servo
Rising up the spindle and FG servo becomes on by pressing [TEST]
and [5] keys in order.