Monessen Hearth AVFLST42NTSC Installation & Operating Instructions Manual page 24

TOUCH SCREEN REMOTE CONTROL OPERATION
NOTE: There will be a
ten (10) second delay
for the flame adjustment
when the fireplace is
turned on.
1. When Set Temp. is
3° F or higher than
Room Temp., flame
height will be on High.
2. When Set Temp.
is 2° F higher than
Room Temp., flame
height will be on Me-
dium.
3. When Set Temp.
is 1° F higher than
Room Temp., flame
height will be on Low.
4. When Set Temp. is equal to Room Temp., flame height
does not change (stays on low).
5. When Set Temp. is lower than Room Temp., the fire-
place will be shut off.
6. When Set Temp. is 1° F higher than Room Temp.,
again the flame height will be on Low.
To exit Smart Mode and shut off the fireplace;
a. Press the OFF button,
or
b. Press and hold the THERMO buttons for 3 seconds
or
c. Slide down on the arrow buttons.
To shut off the Smart Mode option and return to regular
thermostat mode, press and hold the THERMO button
and the ON/UP button at the same time for 3 seconds
again.
Top Light Brightness Control
Figure 27
The top light brightness control function is used to adjust
the brightness of the top light bulb connected to the AC
module on the Signature Com-
mand System. There are four
®
light brightness levels defined:
Off, Low, Medium, High
1. Press the LIGHT button to en-
ter the light brightness control
mode. The LIGHT icon will
start flashing.
2. Press the On/up and OFF/
down buttons to increase/
decrease the light brightness
(Off-Low-Medium-High).
24
Smart
Mode
Icon
Figure 26.
FP2654
smart mode
Figure 27.
FP2657
Light bright control
3. Press the light button again to confirm the setting. The
new setting will be transmitted to the receiver.
4. After the signal is sent, the On/up and Off/down but-
tons become flame height controller again.
5. When the light button is flashing, slide up and down on
the arrow buttons will turn the light brightness to HIGH
or Off directly without pressing the light button again to
confirm.
AUX Control
The AUX control function is used to turn on or
turn off the overhead light connected to the AC
module of the Signature Command
Press the AUX button to turn on or turn off the
overhead light.
1. When the auxiliary is turned on, the icon will
become solid text and the "ON" icon will ap-
pear below the "AUX" icon.
2. When the auxiliary is turned off, the icon will become
hollow text and the "ON" icon will disappear.
NOTE: Some fireplaces use the AUX function to control
options within the fireplace.
Setting up Blank Screen or Constant Display in Idle
Figure 28
There is an option
to set up how the
LCD displays and
functions when the
transmitter is in
idle. There are two
choices:
1. A) Mode. When
the transmit-
ter is in idle,
the icons in the
"touch area"
Figure 28.
(timer, thermo-
stat, blower, light and AUX) will disappear, as shown
in the figure on the left. When any of the touch buttons
is pressed, those icons will appear and are ready to
operate (default).
2. B) Mode. The transmitter always displays all available
icons showing current status of timer,
blower, light and AUX as shown in the figure on the
right.
Press TIMER and THERMO buttons at the same time for
3 seconds to toggle between A) and B).
1. When the current setting is A), touch any place in the
touch area to bring up the icons then press TIMER but-
ton and THERMO button at the same time for 3 sec-
onds. The backlight will flash once to indicate that the
setting has changed to B).
AVFLST Vent Free Fireplace
System.
®
FP2658
AUX
FP2659
blank screen
thermostat,
20308636