Related Manuals for AUTOTERM PLANAR-2D-12/24
Summary of Contents for AUTOTERM PLANAR-2D-12/24
- Page 1 Installation Instructions PLANAR-2D-12/24 Air heater PLANAR-4DM2-12/24-P PLANAR-44D-12/24-GP-P PLANAR-8DM-12/24-P...
-
Page 2: Table Of Contents
Contents Connections Diagram PLANAR-2D Connections Diagram PLANAR-4DM2 Connections Diagram PLANAR-44D Connections Diagram PLANAR-8DM Introduction Application / modification Safety Installation PLANAR-2D Heater Dimensions PLANAR-4DM2 Heater Dimensions PLANAR-44D Heater Dimensions PLANAR-8DM Heater Dimensions Heater Mounting Position Heater Mounting holes Checking the Heater after Installation Recommendations Electrical Wiring Diagram... -
Page 3: Connections Diagram Planar-2D
Connections Diagram. Main Parts and units of PLANAR-2D... -
Page 4: Connections Diagram Planar-4Dm2
Connections Diagram. Main parts and units of PLANAR-4DM2 mod. P... -
Page 5: Connections Diagram Planar-44D
Connections Diagram. Main parts and units of PLANAR-44D mod. P... -
Page 6: Connections Diagram Planar-8Dm
Connections Diagram. Main parts and units of PLANAR-8DM mod. P... -
Page 7: Introduction
Technical Description Modification Introduction Heaters run on diesel fuel. These Instructions are designed for organizations and Voltage designations in heater labeling: users engaged in the installation of PLANAR air heaters. The «12» designed to operate with power supply voltage of 12V; document describes basic rules of installation of products in ... -
Page 8: Safety
2 Safety Instructions The fuel line shall not be installed inside Installation of the heater and its component the cabin of a vehicle. parts shall be carried out by specialized Wiring (harnesses) shall not be installed organizations approved by the manufacturer. near the fuel line. -
Page 9: Installation
3 Installation When mounting the heater, care should be taken to ensure that its housing does not have harmful Observe safety requirements during heater contact with projecting parts of the floor or other installation. parts of the cabin. 3.1 Mounting Location Installation of air ducts to the air heater The heater can be mounted both inside and outside the PLANAR-8DM is forbidden... -
Page 10: Planar-2D Heater Dimensions
PLANAR-2D Heater Dimensions... -
Page 11: Planar-4Dm2 Heater Dimensions
PLANAR-4DM2 Heater Dimensions... -
Page 12: Planar-44D Heater Dimensions
PLANAR-44D Heater Dimensions... -
Page 13: Planar-8Dm Heater Dimensions
PLANAR-8DM Heater Dimensions... -
Page 14: Heater Mounting Position
Heater Mounting Position... - Page 15 Heater Mounting Position...
-
Page 16: Heater Mounting Holes
Heater Mounting holes... - Page 17 3.4 Heating Air Supply Installation of air ducts to the air heater Heating air is taken from inside the room or from PLANAR-8DM is forbidden outside. Outside air should come from spaces protected from When using a mounting box, outlet should be sealed in rain, splashes and dirt, it should not be exposed to water such a manner that the box itself did not get hot air.
- Page 18 Exhaust gases should be discharged to the outside. The end of the exhaust pipe should not touch Furthermore, the gases should not adversely affect the operation the rubber sealing of the heater. of vehicle units. The outlet of the exhaust pipe should be in such a position that would prevent clogging or entering of snow, and When mounting the exhaust pipe, care should also provide for free drain of any water that got into it.
- Page 19 Both exhaust and intake pipes should be positioned When installing the heater inside van bodies inclined downward from the heater (Fig.16). If this is not (insulated vans, box vans, etc.), the exhaust pipe possible, then a hole Ø3 mm should be made at the lowest outlet and the air intake shall not be placed on point to drain condensate.
- Page 21 3.8 Insulation In order to avoid leakage of fuel from the fuel tank (by gravity) when the fuel pump loses its tightness, the fuel tank At installation of an exhaust pipe it is necessary to consider it's high temperature (to 500 °C, depending on should be preferably placed in such a way that the maximum fuel level is below the cut-off plane of the fuel tube of the heater.
- Page 22 3.9.2. Fuel Pickup Installation 3.9.3 Fuel Pump Installation Fuel pickup is mounted on the fuel tank as shown in The fuel pump is used for metered supply of fuel into the Fig.20(a). Fig.20(b) shows installation of a special washer combustion chamber. with the fuel pickup in the fuel tank hole.
- Page 23 3.9.4 Fuel Line Installation. Cutting of couplings and fuel tubes should be done only with a sharp knife. Interfaces shall not Installation of the fuel line between the fuel pickup be crushed and must be free of burrs or narrowing and the heater is shown in Fig.24.
- Page 24 3.9.6 Heater Electrical Wiring Installation. Installation of the fuel pump electrical harness connector is shown in Fig.27. Installation of wire harnesses and other electrical parts of the heater should be made according to the wiring diagram. The possibility of heating, deformation and movement of harnesses during operation of the vehicle must be eliminated.
- Page 25 3.9.7 Controller Installation 3.9.8 Cab Sensor Installation Controller is mounted in any place convenient for the Cabin sensor (Fig.29) is designed to measure air driver (personnel). The Controller is mounted by means temperature in the area of its installation, which allows to either of double-sided tape or a bracket: maintain there the desired temperature.
-
Page 26: Checking The Heater After Installation
25A fuses are good. If you are unable to determine the cause of the fault, please contact your local dealer, or visit www.autoterm.ru. * - optional. -
Page 27: Electrical Wiring Diagram
PLANAR-2D Electrical Wiring Diagram... - Page 28 Electrical Wiring Diagram PLANAR-44D и PLANAR-4DM2 mod «Р»...
- Page 29 Electrical Wiring Diagram PLANAR-8DM mod «Р»...
Need help?
Do you have a question about the PLANAR-2D-12/24 and is the answer not in the manual?
Questions and answers