McIntosh MHA100 Owner's Manual page 25

choices available, the correct impedance and power
output for the Headphones that will be used for
listening. Refer to figures 72 thru 78.
2. If desired, select the HXD TM Mode by momentarily
press the the VOLUME Control. The HXD Icon
located above the Headphone Jack will illuminate
Green. Refer to figure 71.
3. If desired, select the amount of TRIM Bass Boost
by momentarily pressing the INPUT Control.
Then rotate the INPUT Control to select BASS
BOOST followed by using the OUTPUT Control-
for the desired increase. Refer to figures 53 and 54
on page 21.
CREATE A PROFILE
With the Impedance/Power, HXD and Bass Boost set-
tings made, they will now be assigned to Profile1, for
easy recall at a later time. The PROFILE and VOL-
UME Controls are used to perform the various Profile
the PROFILE Control is rotated and there are no saved
Profiles the Front Panel Display will indicate.the cur-
rently selected Input and "NO PROFILE SAVED".
Refer to figure 79.
INPUT: UNBAL
NO PROFILE SAVED
Figure 79
Create new Profile1 by following the below steps:
4. Press and hold in the VOLUME CONTROL until
the Front Panel Display indicates "SAVE PRO-
FILE, Profile1". Refer to figure 80.
SAVE PROFILE
Profile1
Figure 80
5. To store "Profile 1" into memory press and hold in
the VOLUME CONTROL until the Front Panel
Display indicated "SAVE PROFILE, Profile
Saved". Refer to figure 81.
SAVE PROFILE
Profile Saved
Figure 81
6. To exit the Profile Setup Mode momentarily press
the VOLUME Control.
To select a previously saved Profile perform the foll-
wing steps:
7. Rotate the PROFILE Control to select from the
available Profiles stored in memory. Refer to
figure 82.
INPUT: UNBAL
Profile1
Figure 82
Note: The first time the PROFILE Control is
rotated, the Front Panel Display will indi-
cate the current Profile selection. Refer to
figure 83.
INPUT: UNBAL
PROFILE NOT SET
Figure 83
RENAMING A PROFILE
The MHA100 Profile Name (Profile1 thru Profile5 as
ized with a different name up to eight characters long
ing the input include the following: ! < > * , / - _ 0 1
2 3 4 5 6 7 8 9 a b c d e f g h i j k l m n o p q r s t u v
w x y z A B C D E F G H I J K L M N O P Q R S T
U V W X Y Z . In this example the previously created
and saved Profile1 will be renamed to "Y10-PRO" by
performing the follwing steps:
How to Operate the MHA100, con't
8. Refering to figure 84, rotate the PROFILE Control
to select "NAME PROFILE, Profile1".
NAME PROFILE
Profile1
Figure 84
9. Press and hold the VOLUME Control until the
the character "P" of the "Profile1" starts flashing.
Refer to figure 85.
NAME PROFILE
Profile1
Figure 85
11. Rotate the PROFILE Control until the character
"Y" appears . Then Rotate the OUTPUT Control
until the character "r" of the "Yrofile1" starts
flashing. Refer to figure 86.
NAME PROFILE
Yrofile1
Figure 86
12. Rotate the PROFILE Control until the character
"1" appears. Then rotate the OUTPUT until the
character "o" of the "Y1ofile1" starts flashing.
Refer to figure 87.
NAME PROFILE
Y1ofile1
-
Figure 87
13. Repeat steps 9 thru 12 until the new name of
-
"Y10-PRO" is indicated on the Front Panel Dis-
play. Refer to figure 88.
NAME PROFILE
Y10-PRO
Figure 88
25