Panasonic AJ-HDX400P Operating Instructions Manual page 41

Chapter 4 Adjustments and settings for recording
Display item
INH
4 Information
S.GAIN ¢¢dB/OFF
allocated to USER
DS.GAIN ¢¢:/OFF
buttons
LINE MIX ON/OFF
UM: USER MAIN
S.IRIS ON/OFF
U1: USER1 button
I.OVR ON/OFF
U2: USER2 button
S.BLK –¢¢/OFF
B.STR ON/OFF
AUDIO CH1
AUDIO CH2
REC SW
Y GET ON
RET SW
ATW ON/OFF
D.ZOOM a2/a3/a4/OFF
5 Filter positions 1 to 4
A to D
–
A
6 WHITE BAL switch
B
position
P
T
7 Cumulative gain 6:/10:/12:/15:/20:
display
M
8 8 LINE MIX GAIN
display
9 Gain value
¢¢dB
REC WARNING
: VTR warnings,
SLACK E-¢¢
information
HUMID
SERVO
RF
BACKUP BATT EMPTY
WIRELESS-RF
; AUDIO input
system and level F
meter W
R
TCG
< Time code display
TCR
(V)UBG AB CD EF 00
(V)UBR 12 34 56 78
CTL
What is displayed
"INH" is indicated when the operation of the USER button has been disabled.
This indicates the value selected for S.GAIN.
This indicates the value selected for DS.GAIN.
This indicates whether LINE MIX GAIN is set to ON or OFF.
This indicates whether S.IRIS is set to ON or OFF.
This appears when the IRIS OVERRIDE setting is enabled (ON).
This indicates whether SUPER BLACK is set to ON or OFF and, if it is
set to ON, it also indicates its value.
This indicates whether BLACK STRETCH (black level gradation
compensation) is set to ON or OFF.
This appears when the input signal to recorded on audio channel 1 has
been switched.
This appears when the input signal to recorded on audio channel 2 has
been switched.
This appears only during MODE CHECK button operations while the
USER button functions as the REC switch.
This appears when the function for measuring the output brightness level (in
% units for approx. 3 seconds for the area near the center marker) is ON.
This appears only during MODE CHECK button operations while the
USER button functions as the RET switch.
This appears when ATW is operating.
This indicates the D.ZOOM status.
This indicates the position of the ND filter.
This indicates the position of the CC filter.
This indicates that the filter has not been set to a proper position.
This indicates that the WHITE BAL switch is set to channel A.
This indicates that the WHITE BAL switch is set to channel B.
This indicates that the WHITE BAL switch is set to PRE.
This indicates that the ATW mode has been set. It flashes when the
brightness and color are outside the operating range.
This indicates the value of the cumulative gain (DS.GAIN) when this
gain function is working.
This appears when LINE MIX GAIN (+6 dB) is active.
This indicates the current gain value.
This indicates that a problem has occurred during recording.
This indicates that a problem has occurred in a mechanism. Depending on the
nature of the trouble concerned, the power may be turned off automatically.
This indicates that condensation has formed.
This indicates that servo lock has not been initiated during recording or
playback.
This indicates that the level of the signals from the tape has dropped.
This signals that it is time to replace the backup battery.
This indicates that the level of the RF signal from the wireless
microphone receiver has dropped.
<Note>
For details on the codes displayed in this area, refer to "6-3-2 Error codes."
This indicates the audio channels selected and their audio levels.
∫
This appears when the AUDIO IN switch is at the FRONT position.
This appears when the AUDIO IN switch is at the WIRELESS position.
This appears when the AUDIO IN switch is at the REAR position.
12:59:59:20 This indicates the TCG (time code generator) value.
12:59:59:20 This indicates the TCR (time code reader) value.
This indicates the UBG VUBG display.
This indicates the UBR VUBR display.
–01:59:59:20 This indicates the CTL-COUNTER value.
Status when display appears
4
41