Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stanley STSM1510
Summary of Contents for Stanley STSM1510
- Page 1 STSM1510 English Page 5...
- Page 2 ENGLISH (Original instructions) Parts Description (Fig. 1 ) FIG. 1 FIG. 1 1. Operating Handle 2. Guard 3. Saw Blade 4. Miter Clamp Handle 5. Miter Latch 6. Miter Scale 7. Left Side Fence 8. Bench Mounting Hole 9. Dust Spout FIG.
- Page 3 ENGLISH (Original instructions) FIG. 3 FIG. 4 FIG. 5 FIG. 6 FIG. 7 FIG. 8...
- Page 4 ENGLISH (Original instructions) FIG. 9 FIG. 10 FIG. 11 FIG. 12...
-
Page 5: Intended Use
• MAKE WORKSHOP KID PROOF with padlocks, master Your Stanley Mitre Saw has been designed for fast cutting in switches, or by removing starter keys. wood, fine finishing or aluminum cutting . General Safety Instructions •... - Page 6 ENGLISH (Original instructions) properly and perform its intended function—check for Conductor size (mm Cable rating (Amperes) alignment of moving parts, binding of moving parts, 0.75 breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is 1.00 damaged should be properly repaired or replaced.
- Page 7 ENGLISH (Original instructions) • DO-Use blade guards at all times. • DON’T-Use without Kerf Plate or when kerf slot is wider than 3/8" • DO-Keep hands out of path of saw blade. • DON’T- Carry saw by work extension or other accessory. •...
- Page 8 ENGLISH (Original instructions) Electrical Connection Installing a New Saw Blade (UNPLUG THE MITRE SAW) Be sure your power supply agrees with the nameplate marking. A voltage decrease of 10 percent or more will DO NOT USE FERROUS METAL or masonry cutting blades cause a loss of power and overheating.
-
Page 9: Operation
ENGLISH (Original instructions) NOTE: Your mitre saw is fully and accurately adjusted at the CAN CHECK THE PATH OF THE BLADE. DO NOT CROSS factory at the time of manufacture. If readjustment due to HANDS, AS SHOWN IN FIGURE 7. shipping and handling or any other reason is required, follow Cutting With Your Saw the steps below to adjust your saw. - Page 10 ENGLISH (Original instructions) If small fibers of wood still split out at the rear of the - Examples - workpiece, stick a piece of masking tape on the wood where No. Sides Angle Mitre the cut will be made. Saw through the tape and carefully remove tape when finished.
-
Page 11: Maintenance
ENGLISH (Original instructions) 2. The angled “flats” on the back of the molding must rest Bowed Material squarely on the fence and table of the saw. When cutting bowed material always position it as shown in INSIDE CORNER: Figure 11 and never like that shown in Figure 12. Positioning the material incorrectly will cause it to pinch the blade near Left side the completion of the cut. - Page 12 4. Incorrect blade for work 4. Change the blade being done • Stanley's policy is one of continuous improvement to our products and, as such, we reserve the right to change product specifications without prior notice. TROUBLE! BLADE DOES NOT COME UP TO SPEED •...
-
Page 13: Specifications
For more information about our Should you find one day that your Stanley product needs authorized service centers and if you need technical advice, replacement, or if it is of no further use to you, do not repair, or genuine factory replacement parts, contact the dispose of it with household waste. - Page 14 Ebrahim Al Zayani, Opposite to Al Fouzan, Jeddah highway or King Abdul Aziz road, Yanbu. Tel: (966-4) 3960980, Fax: (966-4) 3961980. Mohamed Ahmed Bin Afif Est., P.O. Box 530, Yanbu, Al Bahr, Tel: (966-4) 3222626/ 3228867, Fax: (966-4) 3222210. SOUTH AFRICA: Stanley Black & Decker - RSA, 199 Winze Drive Stormill Ext 9 Roodepoort, Tel: (2711) 472 0454, Fax: (2711) 472 0482.
Need help?
Do you have a question about the STSM1510 and is the answer not in the manual?
Questions and answers