Advertisement
Installation Manual
RADAR SENSOR
MODEL
(Product Name: SOLID STATE DOPPLER RADAR)
SAFETY INSTRUCTIONS ................................................................................................ i
SYSTEM CONFIGURATION .......................................................................................... iii
EQUIPMENT LISTS........................................................................................................ iv
FOREWORD .................................................................................................................... v
1. INSTALLATION.......................................................................................................... 1
1.1 Installation Considerations....................................................................................................1
1.2 Installation of the Radar Sensor............................................................................................4
1.3 Wiring....................................................................................................................................7
2. INITIAL SETUP........................................................................................................... 8
2.1 Check Points After Installation ..............................................................................................8
2.2 Initial Setup ...........................................................................................................................8
3. MAINTENANCE, TROUBLE- SHOOTING............................................................... 13
3.1 Maintenance .......................................................................................................................13
3.2 Replacement of Fuse..........................................................................................................13
3.3 Troubleshooting ..................................................................................................................14
SPECIFICATIONS ..................................................................................................... SP-1
PACKING LISTS ......................................................................................................... A-1
OUTLINE DRAWING ................................................................................................... D-1
INTERCONNECTION DIAGRAM ................................................................................ S-1
Declaration of Conformity
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Advertisement
Table of Contents
Related Manuals for Furuno DRS4D-NXT
Summary of Contents for Furuno DRS4D-NXT
-
Page 1: Table Of Contents
3.2 Replacement of Fuse......................13 3.3 Troubleshooting ........................14 SPECIFICATIONS ..................... SP-1 PACKING LISTS ......................A-1 OUTLINE DRAWING ....................D-1 INTERCONNECTION DIAGRAM ................S-1 Declaration of Conformity www.furuno.com All brand and product names are trademarks, registered trademarks or service marks of their respective holders. -
Page 2: Safety Instructions
SAFETY INSTRUCTIONS The installer of the equipment must read the safety instructions before attempting to install the equipment. Indicates a potentially hazardous situation which, if not avoided, WARNING could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, CAUTION can result in minor or moderate injury. - Page 3 Model 100W/m 50W/m 10W/m DRS4D-NXT 0.7 m WARNING LABEL A warning label is attached to the antenna unit. Do not remove the label. If the label is missing or damaged, contact your dealer about replacement. Name: Warning Label (2)
-
Page 4: System Configuration
SYSTEM CONFIGURATION RADAR SENSOR DRS4D-NXT Cable Assembly Power/LAN cable CP03-36400/ CP03-36410/ CP03-36420/ CP03-36430 (10/15/20/30 m, 15 m is set as standard.) Multi Function Display Power supply TZTL12F/TZTL15F 12/24 VDC TZT9/TZT14/TZTBB : Standard supply : Local supply Software upgrade to version 3.01 (Planned release: Middle of 2016) or later is required. -
Page 5: Equipment Lists
EQUIPMENT LISTS Standard supply Name Type Code No. Remarks Radar Sensor RSB-135-115 000-029-247 Installation Materials CP03-37001 001-426-200 CP03-36400 000-027-211 Select one Cable Assembly, 10 m CP03-36410 000-027-212 Cable Assembly, 15 m CP03-36420 000-027-213 Cable Assembly, 20 m CP03-36430 000-027-214 Cable Assembly, 30 m Spare Parts SP03-18101 001-426-190... -
Page 6: Foreword
FOREWORD General Information about DRS4D-NXT • TARGET ANALYZER* function displays targets which is moving and getting close to own ship in red and other targets in different colors. Speed analyzing range is ±50 kn. * Requires a GPS sensor. When you change the setting of [Target Analyzer Mode] to [Rain], rain clutter is displayed. -
Page 7: Installation
INSTALLATION Installation Considerations NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. • Do not paint the radome, radar wave emission may be affected. •... - Page 8 Typical installation on a sailboat and power boat Consideration for selecting a location for installation (multiple radars) • In case multiple radars are installed on a ship, DO NOT install the DRS4D-NXT within the range of beam area emitted from other radar(s). Use the illustration below for reference when selecting a suitable location for installation.
- Page 9 1. INSTALLATION Installation with the radiotelephone equipment • Install the radome away from radiocommunication antennas (SSB, VHF, Inmarasat) and GPS antenna to prevent radar interference. • Install the radome away from the radiotelephone equipment so that electrical noise does not affect the radiotelephone equipment. Cable routing •...
-
Page 10: Installation Of The Radar Sensor
1. INSTALLATION Installation on a platform There are 5 steps necessary to install the radar sensor. The illustration below summa- rizes the installation. STERN Align bow mark (Δ) on Power/LAN cable (1 m) radome with ship’s bow. Platform Flat washer Holes drilled referring to the outline drawing and the mounting template in this manual. - Page 11 1. INSTALLATION 4. Connect the power/ LAN cable to the cable assembly. Follow these guidelines for laying the power/LAN cable • The connectors must not strike any part of the vessel due to wind, etc. • Do not apply any load to the connectors. •...
- Page 12 1. INSTALLATION Installation with the radome mount The optional radome mount lets you fasten the radar sensor to a mast on a sailboat. Name, Type: Radome Mount, OP03-208 Code No.: 001-078-340 Name Type Code No. Mounting plate 03-018-9001-0 100-206-740-10 Support plate (1) 03-018-9002-3 100-206-753-10 Support plate (2)
-
Page 13: Wiring
1.3.1 Power requirement The DRS4D-NXT requires either 12 VDC or 24 VDC power. Connect the red cable to the positive terminal of ship’s battery; the blue cable to the negative terminal. The black cable is a shielding cable for grounding. -
Page 14: Initial Setup
• Turning the power on and initial setup Mechanical checks Check below points before switching on the DRS4D-NXT. • All washers are in place and bolts are fully fastened. • All connections are secure and network cable is connected to the multi function dis- play device. - Page 15 2. INITIAL SETUP 4. Drag the [Radar] menu display to show the menu item [Radar Initial Setup], then tap [Radar Initial Setup]. 5. Referring to the tables below, set up the radar. [Radar] menu - [Radar Initial Setup] Menu item Description [Antenna Rotation] Select the speed of antenna rotation.
- Page 16 2. INITIAL SETUP 2. Turn the vessel’s bow toward a target. 3. Tap the [Home] icon to show the home screen and display mode settings. 4. Tap [Radar] to show the [Radar] menu. 5. Drag the [Radar] menu to show the [RADAR INITAL SETUP] menu. 6.
- Page 17 2. INITIAL SETUP 5. Drag the [Menu Radar] sub menus to find the menu item [Radar Initial Setup]. Title Menu Radar (Radar Initial Setup) Menu item Description [Antenna Rotation] Select the speed of antenna rotation. [Antenna Heading See the topic of "How to align the antenna heading" on page 2-12. Align] [Main Bang Sup- If main bang appears at the screen center, slide the circle icon so...
- Page 18 2. INITIAL SETUP 1) Select a range between 0.125 and 0.25 NM and set the mode to “head up“. You can select a range by a pinch action. The range and range ring interval appear at the bottom left of the screen. Range Range ring interval Zoom in...
-
Page 19: Maintenance, Trouble- Shooting
MAINTENANCE, TROUBLE- SHOOTING WARNING DO NOT OPEN THE SENSOR. Electrical shock hazard There are no user-serviceable parts inside. Only qualified personnel are allowed to work inside the equipment. Maintenance Regular maintenance is important for good performance. Check the points mentioned below every 3 to 6 months to keep the radar sensor in good working order. -
Page 20: Troubleshooting
3. MAINTENANCE, TROUBLE- SHOOTING Troubleshooting The table below provides simple troubleshooting procedures to restore normal opera- tion. If you cannot restore normal operation, contact your dealer for advice. Trouble Remedy The radar type does not appear • Check if the Cable Assembly is connected to the on the multi function display de- power source and the power source is on. -
Page 21: Specifications
FURUNO DRS4D-NXT SPECIFICATIONS OF RADAR SENSOR DRS4D-NXT RADIATOR Antenna type Patch array antenna Antenna length 22-inch Horizontal beam width 3.9° typical (-3dB) Adjustable between 2.0° and 3.9° (effective with RezBoost control) Vertical beam width 25° (-3dB) Sidelobe attenuation -24 dB... - Page 23 C3649-M01-A...
- Page 24 SPARE PARTS LIST FOR U S E VESSEL QUANTITY REMARKS/CODE NO. DWG. NO. NAME OF ITEM WORKING OUTLINE PART TYPE NO. SPARE ﾋｭｰｽﾞ FUSE FRU-2P5S-FU- 5A-B 000-168-869-10 MFR'S NAME FURUNO ELECTRIC CO.,LTD. DWG NO. 03HR-X-9301 （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
- Page 27 When a claim is made, FURUNO has a right to choose whether with other electronic devices. The imported product may also be to repair the product or replace it.
- Page 28 24 months from installation date provided the work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius of 50 miles of the shop location.
- Page 32 ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A : DEC 2015 Printed in Japan All rights reserved. B1 : MAY 30, 2016 Pub. No. IME-36490-B1 (TASU ) DRS4D-NXT 0 0 0 1 9 1 0 8 2 1 1...