TABLE OF CONTENTS PAGE PAGE 1 Safety Precaution -------------------------------------------------3 1.1. General Guidelines ----------------------------------------3 1.2. Leakage Current Cold Check ---------------------------3 1.3. Leakage Current Hot Check (See Figure 1.)--------3 1.4. How to Discharge the Capacitor on Jack PCB -----4 2 Warning --------------------------------------------------------------5 2.1.
1 Safety Precaution 1.1. General Guidelines 1.3. Leakage Current Hot Check 1. IMPORTANT SAFETY NOTICE (See Figure 1.) There are special components used in this equipment 1. Plug the AC cord directly into the AC outlet. Do not use which are important for safety. These parts are marked by an isolation transformer for this check.
1.4. How to Discharge the Capacitor on Jack PCB When removal the jack P.C.B., it is protected with a capacitor cover. So do not have to discharge the capacitor. However, when replacement it, remove the capacitor cover with unscrew 2 points, and then discharge the capacitor as follows. CAUTION: 1.
2 Warning 2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
2.3.2.3. How to Replace the Fuse A replacement fuse cover can be purchased from your local Panasonic Dealer. 1. Remove the Fuse Cover with a screwdriver. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety.
2.4. How to Replace the Lithium Battery 2.4.1. Replacement Procedure 1. Remove the JACK PCB. (Refer to Disassembly Procedures.) 2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B4001” at foil side of JACK PCB) and remove the Lithium battery together with electric lead terminal.
3 Service Navigation 3.1. Introduction This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual. 3.2.
3.4. How to Define the Model Suffix (NTSC or PAL model) There are four kinds of HDC-SD1. • a) HDC-SD1S • b) HDC-SD1PP • c) HDC-SD1EG • d) HDC-SD1GC (HDC-SD1S is exclusively Japan domestic model.) What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main PCB.
6 Service Mode 1. Indication method of the service menu Set the mode dial other than PC connection mode. 2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to “[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed. Service mode menu Screen display Contents...
6.1. Lock Search History Indication 1. Set the mode dial other than PC connection mode. 2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to “[FOCUS]” position for more than 3 seconds until the top screen of the Service Menu being displayed. 3.
7 Service Fixture & Tools 7.1. When Replacing the Main PCB After replacing the MAIN PCB, be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in “TSN system”, together with Maintenance software. 7.2.
Page 19
CAUTION-1. (When servicing JACK PCB) 1. Be sure to discharge the capacitor on JACK PCB. Refer to “HOW TO DISCHARGE THE CAPACITOR ON JACK PCB”. The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed. 2.
8.3. Disassembly Procedure Item Removal Lens Unit Fig. D24 1 Screw (V) Item Removal 1 Screw (W) Lens Hood Unit Fig. D1 Lens Hood Unit 1 Locking tab Side Case (R) Unit Fig. D2 2 Screws (A) Lens Frame Unit Fig.
Page 22
8.3.1. Removal of the Lens Hood Unit Item Removal IRIS Unit Fig. D49 Solder (12 points) 1 Screw (l) OIS Unit IRIS Unit Master Frange Unit, Fig. D50 2 Side Yorks 4th Lens Frame Move Guide Pole (F) Unit 2 Guide Poles (Z) 4th Lens Frame Move Unit Master Frange Unit Fig.
Page 24
8.3.3. Removal of the Barrier Motor Unit Fig. D7 Fig. D9 8.3.4. Removal of the Side Case(L) Unit Fig. D8 Fig. D10...
Page 25
8.3.5. Removal of the Speaker Holder Unit Fig. D11 Fig. D13 8.3.6. Removal of the Top/Rear Operation Unit Fig. D12 Fig. D14...
Page 26
8.3.7. Removal of the Jack Board/Jack Heat Sink Fig. D17 Fig. D15 8.3.9. Removal of the Battery Case Unit 8.3.8. Removal of the Jack P.C.B. Unit Fig. D18 Fig. D16...
Page 27
Fig. D19 Fig. D21 8.3.10. Removal of the Main P.C.B. Fig. D22 Fig. D20 Fig. D23...
Page 28
8.3.11. Removal of the Lens Unit 8.3.12. Removal of the Sub P.C.B. Fig. D27 8.3.13. Removal of the LCD Unit Fig. D24 Fig. D28 Fig. D25 Fig. D29 Fig. D26...
Page 29
8.3.14. Removal of the Monitor P.C.B. Fig. D30 Fig. D32 Fig. D33 Fig. D31 Fig. D34...
Page 30
8.3.15. Removal of the LCD 8.3.16. Removal of the Battery Flex Unit Fig. D36 Fig. D37 8.3.17. Removal of the Battery Lock Fig. D35 Fig. D38...
Page 31
8.3.19. Removal of the Prism Unit and Optical Filter Fig. D39 8.3.18. Removal of the Battery Cover and Battery Cover Hinge Unit Fig. D42 Fig. D40 Fig. D43 Fig. D41...
Page 32
8.3.20. Removal of the Zoom Motor Unit Fig. D45 8.3.21. Removal of the 1st Lens Frame Move Unit Fig. D44 Fig. D46...
Page 33
8.3.22. Removal of the Main Frame and 8.3.24. Removal of the IRIS Unit 2nd Lens Frame Move Unit Fig. D47 8.3.23. Removal of the 2nd Lens Spring and OIS/IRIS Unit Fig. D49 Fig. D48...
Page 34
8.3.25. Removal of the Master Frange Unit and 4th Lens Frame Move Unit Fig. D50...
9 Measurements and Adjustments 9.1. Electric Adjustment • Adjustment method is different from a conventional SD video camera. • An exclusive jig and PC (including software for adjustment “Tatsujin”) are necessary for electric adjustment. • A USB driver for service is necessary to communication with PC. •...
Page 36
Adjustment Items • Adjustment item as follows. The adjustment instruction is available at "Software download" on the "Support Information from NWBG/VDBG-PAVC" web-site in "TSN System".
10 Factory Setting 10.1. HOW TO TURN ON THE FACTORY SETTINGS? 1. Set the mode dial other than PC connection mode. 2. While keep pressing the “[LEFT<] of cursor” button and “delete” button, hold down the Mode Select Switch towards to “[FOCUS]”...
Page 38
"Standard-Playback" mode when there is no specify mode is mentioned. Model No. HDC-SD1PP 4.Although the voltage and waveform available on here is measured with standard frame, it may be differ from actual measurement due to modification of circuit and so on.
S2. Voltage Chart Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. S2.1.
S4. Schematic Diagram S4.1. Interconnection Diagram SPEAKER FAN MOTOR P6902 EVF UNIT PW REG5V SIDE R PCB FAN FG D GND REAR OPERATION (FOIL SIDE) UNIT FP601 FP6902 FP6903 FLASH CLK3 M CKH2 P6901 CLK3 M CKH2 MAIN PCB M STH CLK3 M CKH1 UNIT M DSG...
S6. Replacement Parts List Note: 1.* Be sure to make your orders of replacement parts according to this list. 2. IMPORTANT SAFETY NOTICE Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. 3.
Page 65
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks LB4006 J0JYC0000059 FILTER VEP03H10C-5 MAIN P.C.B. 1 (RTL)(E.S.D.) (PP) LB4008 J0JYC0000061 FILTER LB4009 J0JYC0000059 FILTER VEP03H10B MAIN P.C.B. 1 (RTL)(E.S.D.) (EG) LB4010...
Page 66
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks S6392 EVQPQ6B55 SWITCH T7001 G5D1A0000040 TRANSFORMER S6394 K0H1BA000436 SWITCH S6395 K0L1AA000011 SWITCH VA4902 D4ED18R00008 VARISTORS VA4903 D4ED18R00008 VARISTORS VEP20C00A FRONT P.C.B. (RTL)(E.S.D.) VEP20B99A SIDE-R P.C.B.
Page 67
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VEP20C01A LCD DET P.C.B. (RTL)(E.S.D.) IC4801 NJM2115V 1 (E.S.D.) S6701 K0L1AA000011 SWITCH IC4802 NJM2115V 1 (E.S.D.) IC4803 NJM2115V 1 (E.S.D.) Q4801 2SD2216J0L TRANSISTOR 1 (E.S.D.)
Page 68
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VHD1904 SCREW 1 VQL1L86 CAUTION LABEL A 1 (PP) XQN16+B6FN SCREW 1 VQL1L84 CAUTION LABEL A 1 (EG) XQN16+BJ5FN SCREW ...
Page 69
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks XQN16+B5FN SCREW VSC5906 HEAT SINK FRAME 1 XQN16+B5FN SCREW VMG1772 DAMPER RUBBER XQN16+B5FN SCREW VMG1772 DAMPER RUBBER XQN16+B6FN SCREW VGQ9175 HEAT RADIATION SHEET A1...
Page 70
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks L5BDDXM00008 LCD VEP26293A MONITOR P.C.B. 1 (RTL) VGL1208 DIFFUSION SHEET VGL1209 PRISM SHEET A VGL1210 PRISM SHEET B VGL1211 REFLECTION SHEET VKW3321...
Page 71
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VXQ1463 PRISM UNIT 201-1 VEP22375A CCD FPC U VGQ9068 CCD HEAT SINK SHEET VXW0826 LENS UNIT (W/O CCD) L6HA66NC0010 STEPPING MOTOR VXP2687...
Page 72
HDC-SD1PP-S,EG-S,GC-S vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VPK3207 ACCESSORIES BOX 1 (PP) VPK3208 ACCESSORIES BOX 1 (EG),(GC) 302 ------------ BATTERY PACK 1 (PP) 302 ------------ BATTERY PACK...
Need help?
Do you have a question about the HDC-SD1PP and is the answer not in the manual?
Questions and answers