Unique UGP 22 Owner's Manual
  1. Manuals
  2. Brands
  3. Unique Manuals
  4. Refrigerator
  5. UGP 22
  6. Owner's manual

Unique UGP 22 Owner's Manual

Propane refrigerator 625.8 l / 22.1 cu. ft.
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
625.8 L / 22.1 cu. ft.
UGP 22
Propane Refrigerator
OWNER'S GUIDE
serial number:
March 2016

Advertisement

Table of Contents
loading

Related Manuals for Unique UGP 22

Summary of Contents for Unique UGP 22

  • Page 1 625.8 L / 22.1 cu. ft. UGP 22 Propane Refrigerator OWNER’S GUIDE serial number: March 2016...
  • Page 2 UNIQUE UGP-22 Propane Refrigerator Installation and Owners Manual The installation of the appliance must conform with local codes or, in the absence of local codes, to the national Fuel Gas Code, ANSI Z233.1 and in Canada B149.2 Propane Storage and Handling Code...
  • Page 3 M A N U F A C T U R E D A N D C E R T I F I E D B Y Unique Gas Products Ltd “Personal Service & Knowledge makes us “Personal Service & Knowledge makes us Unique”...

  • Page 4: Table Of Contents

    T able of Contents Chapters Welcome Safety & Warnings Appliance Installation General Operating Instructions How To Use The Refrigerator Maintenance & Service Troubleshooting & Suggested Spares Carbon Monoxide Instructions (CM Model) Door Reversal & Removal Instructions Temperature Controls & Food Storage and Cleaning Parts &...

  • Page 5: Chapters

    U N I Q U E U G P - 2 2 Chapter Welcome & Congratulations ongratulations on your purchase of a UNIQUE refrigerator!. We are very proud of our product and we are completely committed to providing you with the best service possible. Your satisfaction is our #1 priority. Please read this manual very carefully. It contains valuable information on how to properly maintain your new gas refrigerator. We know you will enjoy your new refrigerator and thank you for choosing one of our Unique Gas Products. We hope you will consider us for future purchases. PLEASE READ AND SAVE THESE INSTRUCTIONS This manual provides specific operation instructions for your model. Use your refrigerator only as instructed in this manual. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining the appliance Please record your model and serial # shown below for future reference. This information is found on your CSA rating/serial plate inside the refrigerator compartment. Please mail in the Warranty Registration Card included with your refrigerator or you can register online at www.uniqueoffgrid.com...

  • Page 6: Safety & Warnings

    U G P - 2 2 Safety & Warnings If you smell gas Open windows • Don’t touch electrical switches • Extinguish any open flame • Immediately call your gas supplier • For your Safety Due to the potential of carbon monoxide (CO) from many different sources • inside your dwelling, and to meet most building codes, the dwelling must have a separate wall-mounted CO alarming device. This is beyond any safety devices/construction inherent to the Unique appliance. Do not store or use gasoline or other flammable vapors and liquids in the • vicinity of this unit or any other appliance Warning Improper installation, adjustment, alteration, service or maintenance can • cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency or the gas supplier. This product can produce Carbon Monoxide. Carbon Monoxide has no • odour and can kill you. The burner and flue system must be kept clean. See owner’s manual for cleaning instructions. Installation Instructions The installation of the appliance must conform with •...
  • Page 7 U N I Q U E U G P - 2 2 Chapter Installation of Appliance For best performance at high ambient temperatures, there must be free air circulation over the cooling unit at the rear of the refrigerator. Ensure that there is a free air space above the refrigerator and that the flue (chimney) on top of the cabinet is not covered in any way. Do not place the refrigerator in a space where air circulation is restricted. Follow “clearance” instructions. This free-standing refrigerator requires accessibility to the back for servicing the gas equipment, which can be obtained by using a certified Flexible Metal Connector to allow the refrigerator to be withdrawn without disrupting the gas supply. “Where a flexible metal connector is used, it must comply with local authorities and in Canada with the provisions of the current Standard CAN 1-6.10, Metal Connectors for Gas Appliances”. However, if the Local Authorities require a rigid gas supply connector, the refrigerator should be located with sufficient space at the back for servicing or, if located against a wall a removable panel of a minimum size of 16” x 20” should be provided in the wall to allow access to the rear of the refrigerator. . If you purchased a CM (CO Monitor model) you must follow instructions in Section 6 - 5.0 onward. Heat Shield The heat shield must be installed before operating the appliance. This is a CSA requirement. Un-wrap the heat shield (located inside the box along with the appliance). Mount heat shield with the screws (supplied) to left side of the fridge. See diagram.
  • Page 8 U N I Q U E U G P - 2 2 Clearances Minimum clearances to combustible materials are: Top – 10” Sides – 2” Rear – 1” with left hand side rear shield mounted as shown in Figures. 1, 2 & 3. Note: DO NOT install the appliance directly on carpeting. Carpeting must be removed or protected by a metal or wood panel beneath the appliance, which extends at least the full width and depth of the appliance. Air Flow - to release heat trap Fig#1 - This is ideal as both top and sides are open • Fig#2 – During hot/humid weather this confined area will become very • warm. To reduce heat build-up, we recommend providing an area for two air vents to circulate the air. One placed 6” off the floor and the other at or above the appliance top. Cold air return vents with adjustable louvers, work very well. This will allow hot air to evacuate the area and assist in air flow across the fins (similar to air passing across a radiator) – See Fig #4 Fig#3 – If this is your opening you only need to stay the diagramed distance • from the wall and ceiling. There is no need for additional venting.
  • Page 9 U N I Q U E U G P - 2 2 Gas Connection Hook-up to the gas supply line: 3/8” SAE (UNF 5/8” - 18) male flare connection. A backup wrench must be used when tightening gas supply fitting. All completed connections should be checked for leaks with a non-corrosive leak detector and/or soap and water for a bubble check. – ARNING O NOT USE FLAME TO CHECK FOR GAS LEAKS The gas supply system must incorporate a pressure regulator to maintain a supply pressure of not more than 12” water column and no less than 11” water column. (Max setting) Make sure the refrigerator and any other high BTU appliances on your line are turned on when checking the gas pressure. The appliance and its individual shut- off valve must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of ½” psig. In case detailed instructions on the installation and connection of the gas supply are required, contact your dealer or distributor. Leveling Ensure the fridge is level by using a 2ft level. This is accomplished by adjusting the feet at the front, underneath the fridge.

  • Page 10: General Operating Instructions

    U N I Q U E U G P - 2 2 Chapter General Operating Instructions Importance of Leveling a Refrigerator The refrigerator must be adjusted to a vertical position in both directions. In an absorption refrigeration system, ammonia is liquefied in the finned condenser coil at the top rear of the refrigerator. The liquid ammonia then flows into the evaporator (inside the freezer section) and is exposed to circulating flow of hydrogen gas, which causes the ammonia to evaporate, creating a cold condition in the freezer. When starting this refrigerator for the very first time, the cooling cycle may require up to 8 hours of running time to begin cooling before the unit is fully operational. After 8 hours you can slowly begin loading the compartment. The tubing in the evaporator section is specifically sloped to provide a continuous movement of liquid ammonia, flowing downward by gravity through this section. If the refrigerator is operated when not level, liquid ammonia will accumulate in sections of the evaporator tubing. This will slow the circulation of hydrogen and ammonia gas, or in severe cases, completely block it, resulting in a loss of cooling. Warranty will not cover recharge/rebuild if caused by not running the fridge level. This refrigerator operates only on LP Gas (Propane) Note: After changing an LP tank, or after a long shut off period, the gas line is likely to be filled with air. You may have to repeat the lighting procedure several times to purge the air out of the gas lines.We suggest first turning off gas at the control panel, then the tank,this will reduce an air trap in the gas line.

  • Page 11: Gas Operation

    U N I Q U E U G P - 2 2 Gas Operation “Start Up” Procedure – see Figure # 5 on next page for control panel 1. Locate the control panel below at the bottom front of fridge 2. Turn the gas shut off valve C to the ON position – to the left 3. Turn thermostat button B fully clockwise (Max), start to spark igniter button A before depressing the gas control button E, there may be a period of time required for air to escape from the gas line and flow up to burner. Length of time will vary depending on distance of the fridge to propane tank. Continue pushing the igniter button while holding in the gas button until the needle in the flame indicator D moves into the green area (to the left). 4. When the needle starts to move into the green area, this means flame is now lit. Stop sparking and continue to hold gas button E down for an additional 10 seconds. Release gas button, fridge should now stay lit and the needle should remain in the green area. 5. Once all the above has been done and you are ready to re-start your fridge for use, leave the thermostat button at “4”. Setting the thermostat to "4" will allow the fridge to get to optimum cooling temperature. It may be necessary to adjust the temperature control on the thermostat knob to suit your needs. 6. The quantity of food in the refrigerator, the frequency with which the refrigerator doors are opened and the room temperature will all affect refrigerator temperatures. “Shut Down” Procedure 1. Turn knob C to Gas “Off” position – to the right.
  • Page 12 U N I Q U E U G P - 2 2 Figure #5 Thermostat A thermostat controls the refrigerator cooling temperature; it can be adjusted by turning knob B to different settings to maintain the desired refrigerator temperature. Knob E also incorporates a safety device, which automatically shuts off the supply of gas if the flame goes out. The piezo electric igniter discharges sparks onto the burner when the button is pushed. 1. “Defrost” Defrost Setting on the Gas Thermostat: In gas operation, the thermostat closes its main valve and the burner runs continuously at the bypass rate or pilot flame (counter clockwise turn). 2. “Max” Setting of the Thermostat: In gas operation, the thermostat allows the burner to remain on high flame continuously (clockwise turn). 3. The thermostat can be adjusted between “Max” and “Defrost” to obtain the desired fridge temperature. When the thermostat reaches the set temperature, it will cut the burner back to bypass operation. The setting of the thermostat is critical and recommend it be adjusted to maintain a dry frost on the cooling fins (approx 38° Freinhight or 3° Celcius) . Adjust the thermostat knob closer to “Max” (clockwise) when the outside temperature rises.

  • Page 13: How To Use The Refrigerator

    U N I Q U E U G P - 2 2 How to Use the Refrigerator FOOD STORAGE COMPARTMENT The food storage compartment is completely closed and unventilated, which is necessary to maintain the required low temperature for food storage. The coldest areas in the refrigerator are under the cooling fins and at the bottom of the refrigerator. The warmer areas are on the upper door shelves. This should be considered when placing different types of food in the refrigerator. FROZEN FOOD STORAGE COMPARTMENT Quick frozen soft fruits and ice cream should be placed in the coldest part of the compartment which is at the bottom of the aluminum liner. Frozen vegetables, may be stored in any part of the compartment. This compartment is not designed for deep or quick freezing of food. Meat or fish, whether raw or prepared, can be stored in the frozen food storage compartment provided they are pre-cooled in the refrigerator. To prevent food from drying out, keep it in covered dishes, containers, plastic bags or wrapped in aluminum foil. Defrosting Frost will gradually accumulate inside the refrigerator and freezer surfaces. It must not be allowed to grow too thick as it acts as an insulator and adversely affects the refrigerator performance. Check the formation of frost every week and when it exceeds 3/8” thick, defrost the refrigerator. It will not hurt the fridge to have the ice buildup. If it gets too thick it will act as an insulator and hamper the cooling ability of the fridge. Defrosting can be done with the fridge running if so desired. Simply open both doors and turn thermostat to defrost, or fully counter clockwise. Once the ice starts to melt a towel can be placed under the evaporator fins in the fridge, then pull off the ice. Wipe the fins clean and shut both doors. For the freezer, defrosting time can be reduced by filling a tray with hot water and placing it in the freezer...

  • Page 14: Cleaning

    U N I Q U E U G P - 2 2 RIDGE ECTION Inside the refrigerator compartment, the defrost water runs from a collector channel to a drip tray/cup at the rear of the refrigerator where it normally evaporates. If heavy frost has built up on the cooling fins creating a lot of defrost water, beware your water reservior may overflow, we suggest you inspect reservoir before and after cycle. REEZER ECTION This area must be wiped down with cloths to remove water after defrosting; there is no drain for this compartment Note: When all frost has melted in the freezer compartment and interior of the refrigerator it should be wiped up with a clean cloth. Set the thermostat to its Max position until the desired interior temperature has been achieved, approx 8 plus hrs dependant on room temperature, and then replace all food. Cleaning Cleaning the refrigerator is usually done after it is defrosted or put into storage. To clean the interior liner of the refrigerator, use lukewarm dish soap solution. Use only warm water to clean the finned evaporator, gasket, ice trays and shelves. Never use strong chemicals or abrasives to clean these parts as the protective surfaces will be damaged. It is important to always keep the refrigerator clean. Dish soap is recommended Interior Light The interior light is located inside the fridge compartment at the top. You can replace it by unscrewing counter clockwise. Four “D” size batteries operate the interior light. The battery compartment is located on the exterior back of the fridge, upper right side while facing the back of the fridge.
  • Page 15 Chapter U N I Q U E U G P - 2 2 Maintiance & Service The user should be aware of service that must be done on a regular schedule to keep the refrigerator operating properly. Installation must be by a licensed gas fitter in accordance with local codes or in the absence of local national Fuel Gas Code, ANSI Z233.1 and in Canada B149.2 Propane Storage and Handling Code (latest edition). REFRIGERATOR REMOVAL Before working on the refrigerator, shut off the gas supply. Disconnect the gas supply line at the rear of the refrigerator. Always use a back up wrench when loosening and tightening this connection. Cap the gas supply line and remove the refrigerator. Replacement is the reverse of removal. Check all connections for gas leaks. Refer to Chapter 2 INSTALLATION PERIODIC MAINTENANCE Before working on refrigerator, shut off the gas supply. Disconnect the gas line at the rear of the refrigerator. Always use a back up wrench when loosening and tightening this connection. Cap the gas supply line and remove refrigerator.
  • Page 16 U N I Q U E U G P - 2 2 Check all connectors in the complete refrigerator LP gas system for gas • leaks. The LP gas supply must be turned on. Apply a non corrosive bubble solution to all LP connections. The appearance of bubbles indicates a leak and should be repaired immediately by a qualified serviceman. – ARNING O NOT USE FLAME TO CHECK FOR GAS LEAKS Check burner flame for proper appearance. The flame should be light blue with no yellow at the tip. See figure #6 Fig. #6 Fig. #7 The LP gas pressure should be checked and the main regulator readjusted • if pressure is incorrect. The correct operating pressure is 11” W.C. (water column). Inspect the flue baffle, it should be clean and free of soot. Any soot • formation indicates improper functioning of the burner. The flue and burner both require cleaning in the following manner: Remove cover from the burner housing. Disconnect the wire from the spark electrode Remove the burner...
  • Page 17 U N I Q U E U G P - 2 2 Remove the wire and flue baffle from the top of flue tube. Clean the flue from the top using a flue brush, be sure to cover the burner if remaining intact to eliminate dirt falling into burner. Replace the flue baffle. Clean burner tube with compressed air, check for fluff or spider webs. Before removing burner orifice, clean burner area of any soot, scale or dirt. Remove the orifice and soak it in alcohol (isopropyl alcohol or thinners) and blow it out with compressed air. Re-install and tighten burner orifice. Re-install burner Warning - DO NOT use a pin or wire when cleaning the burner orifice as damage can occur to the precision opening. This can cause damage to the refrigerator or create a fire hazard. It will also create extremely dangerous levels of carbon monoxide. Be sure to reconnect the wire to the electrode. Check the electrode for proper location and gap. See figure #8 Fig. #8 The inlet & outlet gas fittings on the refrigerator need to be checked for leaks. Apply a non corrosive bubble solution to the fittings and observe for leaks. The safety valve will not allow gas pressure to any connections between it and the burner orifice. These fittings must be checked while burner is in operation (gas flow will be present between saftey valve and burner head). – The safety valve (“E” button Fig#5) must be ARNING manually depressed to allow gas pressure to flow to the burner orifice. Be sure to apply the leak check solution before...
  • Page 18 U N I Q U E U G P - 2 2 o If leak occurs, then allow ten minutes to dissipate from the burner area. Fix leak then light the burner according to the instructions under G – ENERAL PERATIONG NSTRUCTIONS AS OPERATION HAPTER...

  • Page 19: Maintenance & Service

    U N I Q U E U G P - 2 2 Chapter TROUBLESHOOTING INSTRUCTIONS & SUGGESTED SPARE PARTS TO KEEP ON HAND REFRIGERATOR DOES NOT COOL, CHECK LIKELY CAUSES: Burner orifice clogged. Clean. See section Maintenance & Service, C HAPTER Item #2. Periodic Maintenance, Items 1-9. Check to ensure refrigerator is level – (left to right and front to back). Restriction on air flow across cooling unit. Heavy frost build up on evaporator fins. Defrost. Flue baffle not inserted properly in flue tube. Improperly set thermostat. See paragraph on thermostat. In hot weather or heavy use the setting should be closer to “Max” than usual. Burner dirty. Clean. See Section M & AINTENANCE ERVICE HAPTER ERIODIC AINTENANCE LP gas pressure low at burner. Regulator pressure must not drop below 11 inches W.C (water column). C HAPTER...

  • Page 20: Spare Parts

    U N I Q U E U G P - 2 2 Spare Parts The following is a list of commonly used parts which are available: Burner orifice • Burner • Electrode • Thermocouple • Safety valve & thermostat • Piezo igniter (push button) • Baffle • Contact your dealer or an authorized service center for parts and repairs as needed. Quote Model & Serial # - See CSA rating/serial plate on inside left wall.
  • Page 21 U N I Q U E U G P - 2 2 Chapter Carbon Monoxide Monitor Instructions for Model UGP-22 OWNER’S MANUAL Model 9RV-SSO Carbon Monoxide Alarm for Appliance Safety Shutoff ATTENTION: PLEASE READ, FOLLOW AND SAVE! (See Additional Instruction Sheet for Safety Shutoff Connection) Dear New COSTAR 9RV-SSO Owner, Congratulations as you have taken steps to help ensure the health and safety of you and your family. We are proud to offer you our unique, patented CO Sensor technology that detects CO in a manner similar to the human body's response. Please read this owner's manual carefully so you will have a better understanding of the effects of CO poisoning and the COSTAR 9RV-SSO alarming device in conjunction with our UNIQUE propane refrigerator. To your good health and safety, Unique Gas Products...
  • Page 22 U N I Q U E U G P - 2 2 WARNING: Failure to replace this product by the “REPLACE BY DATE” printed on the alarm cover may result in death by Carbon Monoxide poisoning. Replace by date is six (6) years from date of manufacture WHAT YOU SHOULD KNOW ABOUT CO Carbon monoxide (CO) is an insidious poison. It is a colorless, odorless...
  • Page 23 U N I Q U E U G P - 2 2 Individuals with medical problems may consider using warning devices that provide audible and visual signals for carbon monoxide concentrations under 30 ppm. WHAT YOU SHOULD DO IF THE ALARM SOUNDS WARNING Activation of this device indicates the presence of carbon monoxide (CO) which can KILL YOU. If alarm sounds: For users in the United States, follow the protocol in steps 1 through 4 below: 1 Operate reset/silence button; 2 Call your emergency services (____ - ______) [fire department or 911]; 3 Immediately move to fresh air – outdoors or by an open door/window.
  • Page 24 U N I Q U E U G P - 2 2 30 seconds); contact Unique Gas Products for troubleshooting and/or instructions to return the unit: IMPORTANT CONSIDERATIONS: The COSTAR 9RV-SSO has been designed and is warranted to operate for six years. Never disconnect the battery to silence an alarm. The alarm will automatically sense when the level of CO in the air falls below the danger level. You should stay outside the residence, or unconditioned area and remain in fresh air until the alarm is silenced. When the alarm...
  • Page 25 U N I Q U E U G P - 2 2 safely. – Know where to go to call the Fire Department or professional assistance from outside your residence. – Know where to go to call the emergency service provider and or a qualified service technician.
  • Page 26 U N I Q U E U G P - 2 2 WALL LOCATION: Mount the alarm at least 3 feet (usually 5 – 6 feet) from the floor. Figure 1: Recommended CO alarm wall mounting location is 5 to 6 feet from floor 5.3 LOCATIONS TO AVOID: Nuisance alarms are caused by placing units where they will not operate properly. To avoid nuisance alarms, do not place units: – Within 5 feet (1.5m) of any cooking appliance or furnace. – Near an open window or door, because the fresh air entering the opening may delay CO from reaching the alarm. – In damp or very humid areas or next to bathrooms with showers. Install detectors at least 10 feet (3 meters) away from bathrooms. – In very cold or very hot environments or in unheated buildings or outdoor rooms where the temperature can go below or above the operating range of the alarm. Temperature limits for proper operation are -20° F to 120° F ( -29° C to 49° C); Operating Humidity is 10 – 95% RH. – Good ventilation is recommended when household cleaning supplies or similar contaminants are used. CONDITIONS WHICH CAN RESULT IN TEMPORARY CO SITUATIONS: 5.4.1 Excessive spillage or reverse venting of fuel burning appliances (woodstoves, etc) caused by outdoor ambient conditions, such as: 1 Wind direction and/or velocity, including high gusts of wind.
  • Page 27 U N I Q U E U G P - 2 2 3 Simultaneous operation of several fuel burning appliances competing for limited internal air. 4 Vent pipe connections vibrating loose from clothes dryers, furnaces, refrigerators, or water heaters. 5 Obstructions in or unconventional vent pipe designs which can amplify the above situations. 5.4.2 Extended operation of un-vented fuel burning devices (range, oven, fireplace, etc.) 5.4.3 Temperature inversions, which can trap, exhaust gasses near...
  • Page 28 U N I Q U E U G P - 2 2 Step B: Alarm Activation Step C: Removal and Installation Figure 2: Installation Instructions To insure aesthetic alignment of the alarm with the hallway or wall, the UP arrow on the mounting plate must be vertical when wall mounting: (See Step A in Figure 2) As described in Figure 2, attach the mounting plate on the wall. Use the screws and anchors provided to secure the mounting plate. The battery is INSTALLED REVERSED FOR SHIPPING. Remove and reinstall the battery in the correct orientation as noted on the inside of the battery door. When installing the battery, align the “+” and “-“...
  • Page 29 U N I Q U E U G P - 2 2 change the battery; this can be done easily with a long nose pliers. Using the long nose pliers pull the pin out of the hole, it is now possible to remove the alarm from the mounting plate. Figure 3: Tamper Resistant Locking Pin This box contains two self-adhesive labels. You should write the telephone numbers of the emergency service provider and a qualified technician in the space provided on the labels. Place one label next to the alarm, and the other label near a source of fresh air where you...
  • Page 30 U N I Q U E U G P - 2 2 8.2. To clean your alarm, remove it from the mounting bracket as outlined in Figure 2 Step D: Installation/Removal. IF TAMPER RESISTANT PIN HAS BEEN USED, REFER TO STEP 6.7 UNDER INSTALLATION INSTRUCTIONS FOR REMOVAL INSTRUCTIONS. (See Figure 3) 8.3 You can clean the interior of your alarm by using your vacuum cleaner hose and vacuuming through the openings around the perimeter of the alarm.
  • Page 31 U N I Q U E U G P - 2 2 9.3 USE ONLY THE FOLLOWING 9 VOLT BATTERY FOR CO ALARM REPLACEMENT: Alkaline type: DURACELL: MN1604 WARNING USE ONLY THE BATTERY SPECIFIED. USE OF DIFFERENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT ON THE CO ALARM. THE CONSTANT EXPOSURES TO HIGH OR LOW TEMPERATURES OR HIGH HUMIDITY MAY REDUCE BATTERY LIFE. CHECK THE BATTERY MANUFACTURERS SPECIFICATIONS FOR...
  • Page 32 U N I Q U E U G P - 2 2 Chapter Door Removal & Reversal Instructions NOTE: The direction in which your refrigerator doors open (door swing) can be reversed, from left to right or right to left, by moving the door hinges from one side to the other. A qualified person should perform reversing the door swing. Some earlier Stainless Steel models are not reversible, they had to be ordered as Left or Right hinged. 1. Remove toe grille and top hinge cover. 2. Remove top hinge with 3/8” hex driver and lift freezer door off of center hinge pin. Set door aside. 3. Unscrew center hinge pin using adjustable wrench and save for reassembly. Ensure plastic washer stays on hinge pin.
  • Page 33 U N I Q U E U G P - 2 2 9. Move freezer and refrigerator door stops to opposite side. Before starting screws, use an awl to puncture the foam. 10. Position refrigerator door onto bottom hinge pin and screw center hinge pin through center hinge into top of door. Close refrigerator door to help align hinge hole.
  • Page 34 U N I Q U E U G P - 2 2 To Remove Fridge or Freezer Handle (Handles may be easier to reverse while doors are off.) 1. Remove two screws attaching handle to bottom of freezer door. 2. Lift off handle from dovetail screw. To Attach Fridge or Freezer Handle 1. To reinstall handle on opposite side, first remove small plug on side of door. 2. Move dovetail screw from one side of the door to the opposite side 3. Slide the handle over the screw 4. Attach handle to bottom of door – two screws 5. Take removed plug and insert into same hole where you just removed the dovetail screw from...

  • Page 35: Temperature Controls

    U N I Q U E U G P - 2 2 Chapter Temperature Controls Note: Maximum setting is override; therefore the thermostat function is not operational at this setting. This setting is usually only required during very hot and humid days. COOL DOWN PERIOD To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 hours before loading it with food. REFRIGERATOR CONTROL NOTE: When first setting the controls or when changing a setting, wait 24 hours for the temperature to stabilize before making additional changes. TEMPERATURE ADJUSTMENT Adjust temperature gradually: move the knob in small increments, allowing • the temperature to stabilize. For colder interior temperatures, turn the knob clockwise. • For warmer interior temperatures, turn the knob towards counter-clockwise • Adjusting the refrigerator control will change temperatures in both compartments. Remember there is no fan to circulate the air in the refrigerator and freezer compartments as in an electric fridge. For good circulation, do not block the internal cooling fins on back-wall and try to maintain a temperature of 38° F or 4°C in the fridge NOTE: When first turning refrigerator on, move refrigerator controls to maximum, which is the recommended initial setting. After 24 hours, adjust the controls as needed.

  • Page 36: Looking Inside

    U N I Q U E U G P - 2 2 Looking Inside SHELF ADJUSTMENT Refrigerator shelves are easily adjusted to suit individual needs. Before adjusting the shelves, remove all food. Crispers & Deli Drawers The crispers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh produce. Wash items in clean water and remove excess water before placing them in the crispers. Items with strong odors or high moisture content should be wrapped before storing.
  • Page 37 U N I Q U E U G P - 2 2 Food Storage Ideas RESH OOD TORAGE The fresh food compartment should be kept between 38° F and 40° F • (3.3° C and 4.4° C) with an optimum temperature of 38° F (3.3°C). Avoid overcrowding the refrigerator shelves. This reduces the circulation • of air around the food and results in uneven cooling. RUITS AND EGETABLES Storage in the crisper drawers traps moisture to help preserve the fruit •...

  • Page 38: Care And Cleaning

    U N I Q U E U G P - 2 2 OADING THE REEZER Avoid adding too much warm food to the freezer at one time. This overloads • the freezer, slows the rate of freezing, and can raise the temperature of frozen foods. Leave a space between the packages, so cold air can circulate freely, allowing • food to freeze as quickly as possible. Avoid storing hard-to-freeze foods such as ice cream and orange juice on the • freezer door shelves. These foods are best stored in the freezer interior where the temperature varies less. Care and Cleaning Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills immediately and clean both sections at least twice a year. Never use metallic scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any...
  • Page 39 U N I Q U E U G P - 2 2 Chapter Parts Diagram and List...
  • Page 40 U N I Q U E U G P - 2 2...
  • Page 41 U N I Q U E U G P - 2 2...
  • Page 42 U N I Q U E U G P - 2 2 Burner Train Assembly UGP-22...
  • Page 43 U N I Q U E U G P - 2 2 UNIQUE UGP-22 Fridge Item# ESCRIPTION UGP22-01 REEZER ASKET HITE UGP22-02 – B REEZER ASKET LACK UGP22-03 RIDGE OOR GASKET HITE UGP22-04 RIDGE OOR GASKET LACK UGP22-05 HITE UGP22-06...
  • Page 44 U N I Q U E U G P - 2 2 Item# ESCRIPTION UGP22-25 RIDGE HITE UGP22-26 RIDGE TAINLESS TEEL UGP22-27 – B RIDGE LACK UGP22-28 CREW UGP22-29 – T & L RIDGE OWER UGP22-30 – M RIDGE IDDLE UGP22-31 AIRY OVER...
  • Page 45 U N I Q U E U G P - 2 2 Item# ESCRIPTION UGP22-51 INGE OVER LACK UGP22-52 INGE SCREWS UGP22-53 INGE UGP22-54 ORNER HITE UGP22-55 ORNER LACK UGP22-56 IDDLE INGE UGP22-57 YLON ASHER UGP22-58 IDDLE INGE PIN UGP22-59 IDDLE INGE HROME...
  • Page 46 U N I Q U E U G P - 2 2 Item# ESCRIPTION UGP18-52 URNER TUBE UGP18-53 LECTRODE WITH WIRE UGP18-54 RIFICE UGP18-50 HERMOCOUPLE UGP1518-5 NLET GAS UGP1518-4 UTLET UGP18-56 EIZO GNITOR UGP18-57 LAME NDICATOR UGP1518-9 AFETY ALVE UGP1518-2 HERMOSTAT UGP1518-1 ALVE...
  • Page 47 This UNIQUE Refrigerator must be serviced regularly as outlined in the Owner’s Manual. Unique Gas Products Ltd. the seller will not be liable for direct or indirect loss of foods caused by failure in operation. In case of damage, the owner must provide proof of purchase, Model, and Serial Number to the Seller or Unique Gas Products Ltd.

  • Page 48: Limited Warranty

    UNIQUE GAS PRODUCTS LTD offers you this limited warranty on your new carbon monoxide alarm, including all of its component parts except the battery. This limited warranty extends solely to the original end-user purchaser of this product, provided your purchase was made from an authorized vendor. Transfer or resale of this product will automatically terminate warranty coverage. UNIQUE GAS PRODUCTS LTD. warrants the enclosed carbon monoxide alarm to be free from defects in materials and workmanship under authorized use and service, as specified in the owner's manual, for a period of six (5) years from the date of manufacture. UNIQUE GAS PRODUCTS LTD. MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, EXCEPT AS REQUIRED BY LAW, AND IN NO CASE FOR A DURATION LONGER THAN...

Table of Contents