1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 536LiP4
  6. Operator's manual

Husqvarna 536LiP4 Operator's Manual

Hide thumbs Also See for 536LiP4:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Operator's manual
536LiP4 536LiPT5
Please read the operator's manual carefully and make sure you understand the instructions
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 536LiP4

Summary of Contents for Husqvarna 536LiP4

  • Page 1 Operator′s manual 536LiP4 536LiPT5 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols on the machine: that are touching them. If have to work within this safe distance you should always contact the relevant power Translation of the original Swedish operating instruction. company to make sure the power is switched off before you start work.
  • Page 3 KEY TO SYMBOLS The following symbols and decals can be found on your pole saw, battery and battery charger: S-561 82 Huskvarna, Sweden Typ QC 330 2014 Art.No. 966 73 06-01 PRI: 100V - 240V ~ 50-60Hz 330W max. SEC: 36V / 7A max WW/YY –...

  • Page 4: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols on the machine: ........2 Please read the operator's manual carefully. Symbols on the battery and/or on the battery charger: ..............2 WARNING! Long-term exposure to noise Symbols in the operator’s manual: ......2 can result in permanent hearing impairment.

  • Page 5: Introduction

    Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.

  • Page 6: What Is What

    WHAT IS WHAT? 21 17 What is what? Saw head 16 Battery (Accessory) Chain oil tank 17 Warning indicator (ERROR LED) Guide bar 18 Battery indicator button Bar nut 19 Battery status Shaft 20 Activate and deactivate button Harness support hook 21 SavE button Keypad 22 Harness...

  • Page 7: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS General power tool safety • Do not overreach. Keep proper footing and balance at all times. This enables better control of warnings the power tool in unexpected situations. • Dress properly. Do not wear loose clothing or Please read the operator’s manual carefully and make jewellery.
  • Page 8 GENERAL SAFETY PRECAUTIONS Battery tool use and care • Look out for spring back when cutting branches that are under tension. Once the tension in the wood • Recharge only with the charger specified by the fibers is released, the branch can hit the operator and/ manufacturer.

  • Page 9: Personal Protective Equipment

    GENERAL SAFETY PRECAUTIONS • Only use replacement bars and chains specified WARNING! Never allow children to use or by the manufacturer. Incorrect replacement bars be in the vicinity of the machine. Since and chains may cause chain breakage and/or the machine is easy to start, children kickback.

  • Page 10: Battery And Battery Charger

    Never clean the battery or the battery charger with charger from Husqvarna. The batteries are software water. See instructions under the Maintenance encrypted. heading. Use only a Husqvarna original BLi battery in your • Store the battery out of reach of children. machine. •...

  • Page 11: Machine's Safety Equipment

    • the battery in the battery charger outdoors. • the battery in the rain or in wet conditions. Only use Chargers, Husqvarna QC, for charging the • the battery in direct sunlight. Husqvarna replacement batteries, BLi. Use the battery charger only when the surrounding temperature is between 5 °C and 40 °C.

  • Page 12: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Flashing warning indicator (3) and green LED (2) is lit Cutting attachment guard could indicate that: Always use the recommended guard for the cutting • it is not possible to apply full power and, at the same attachment you are using.
  • Page 13 GENERAL SAFETY PRECAUTIONS • Keep the chain properly tensioned! If the chain is • Number of drive links. The number of drive links is slack it is more likely to jump off and lead to increased determined by the length of the bar, the chain pitch wear on the bar, chain and drive sprocket.

  • Page 14: Sharpening Your Chain And Adjusting Raker Clearance

    GENERAL SAFETY PRECAUTIONS • Number of drive links. - Cutting angle - File position Sharpening your chain and adjusting - Round file diameter raker clearance WARNING! The risk of kickback is increased with a badly sharpened chain! General information on sharpening cutting teeth It is very difficult to sharpen a chain correctly without the right equipment.

  • Page 15: Tensioning The Chain

    GENERAL SAFETY PRECAUTIONS teeth on one side of the bar first. Then turn the saw Setting the raker clearance over and file the remaining teeth from the other side. Li-ion Li-ion • Before setting the raker clearance the cutting teeth should be newly sharpened.

  • Page 16: Lubricating Cutting Equipment

    GENERAL SAFETY PRECAUTIONS - Undo the bar nut. • In areas where oil specifically for lubrication of saw chains is unavailable, ordinary EP 90 transmission oil may be used. • Never use waste oil! This is dangerous for yourself, the machine and the environment. Filling with chain oil Fill with oil once an hour or when the battery is dead.

  • Page 17: Checking Wear On Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Checking wear on cutting equipment • If the guide bar is abnormally worn or can be turned an abnormal amount back and forth on the shaft. Saw chain Replace the bar if necessary. • Whether the tip of the bar is uneven or badly worn. If a hollow forms on the underside of the bar tip this is Li-ion Li-ion...

  • Page 18: Assembly

    ASSEMBLY Fitting the bar and chain Rotating the saw head Li-ion Li-ion Li-ion Li-ion • Unscrew the bar nut and remove the protective cover. • Loosen the lock screw. • Fit the bar over the bar bolt. Place the bar in its rearmost position.

  • Page 19: Adjusting The Harness

    ASSEMBLY Adjusting the harness Li-ion Li-ion You should always use the harness with the machine to give maximum control over the machine and reduce the risk of fatigue in your arms and back. • Put on the harness. • Hook the harness onto the suspension loop. •...

  • Page 20: Battery Handling

    BATTERY HANDLING Battery Connect the battery to the battery charger. The display shows the battery capacity and if there are any problems with the battery. The battery capacity is Regularly check that the battery charger and the battery displayed for 5 seconds after the machine is switched off are intact.

  • Page 21: Transport And Storage

    BATTERY HANDLING • Ensure the machine is cleaned and that a complete LED display Charging status service is carried out before long-term storage. The battery is 0%-25% • Transport guard must always be used for storage and LED 1 flashes. charged.

  • Page 22: Starting And Stopping

    Only use the machine for the purpose it was intended for. Connect battery to the machine NOTE! When using Husqvarna BLi batteries and depending on Use the power trigger to control the speed. the battery capacity, there may be deifferences in cutting NOTE! perfomance.

  • Page 23: Working Techniques

    WORKING TECHNIQUES General working instructions • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment. IMPORTANT! • CAUTION! Do not use the machine unless you are This section takes up the basic safety precautions for able to call for help in the event of an accident.

  • Page 24: Stem Limbing

    WORKING TECHNIQUES • Cut large branches in sections so that you have better WARNING! Keep unauthorised persons control over where they fall. You should also pay at a distance. Children, animals, attention to the fact that falling branches can bounce onlookers and helpers should be kept in the direction of the user after hitting the ground.

  • Page 25: Maintenance

    MAINTENANCE Inspection and maintenance • Dismantle the clip holding the washer and the chain drive gear. • Remove the washer. Li-ion Li-ion • Remove the chain drive gear and replace it with a new one. Cleaning WARNING! Always remove the battery before any maintenance on the machine.

  • Page 26: Troubleshooting Schedule

    MAINTENANCE Troubleshooting schedule Keypad Troubleshooting takes place from the keypad. Control panel Possible faults Possible action Green activate LED flashing. Low battery voltage. Charging the battery The power trigger and the activate Release the power trigger and the button are pressed at the same time. machine is active.

  • Page 27: Maintenance Schedule

    Check that the saw head is not damaged. Replace the saw head All service on the saw head must be carried out by if it is damaged. an authorized Husqvarna dealer. Replace the chain drive gear after approx.: 100 Check condition of Drive Sprocket.

  • Page 28: Technical Data

    Driving time and temperature are measured without load according to the operating cycle of 3 seconds operating and 15 seconds of idling. Use only a Husqvarna original BLi battery in your machine. Approved chargers for the specified batteries, BLi. Battery charger...

  • Page 29: Ec Declaration Of Conformity

    Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500 declares that the battery-operated chain clearing saw Husqvarna 536LiP4 and 536LiPT5 with serial numbers dating 2016 and onwards (the year is clearly stated on the rating plate, followed by the serial number) comply with the requirements of the COUNCIL’S DIRECTIVE: - of May 17, 2006 ”relating to machinery”...
  • Page 30 1140199-26 ´®z+H3|¶6K¨ ´®z+H3|¶6K¨ 2016-03-08...

This manual is also suitable for:

536lipt5

Table of Contents