Accessories; Field Installed Options / Accessories - Lincoln Electric VANTAGE 400 Operator's Manual

VANTAGE 400

FIELD INSTALLED OPTIONS / ACCESSORIES

K2641-2 FOUR WHEELED STEERABLE YARD TRAILER
For in plant and yard towing. Comes standard with a Duo-Hitch™, a 2" Ball and
Lunette Eye combination Hitch.
K2636-1 TRAILER - Two-wheeled trailer with optional fender and light package.
For highway use, consult applicable federal, state, and local laws regarding pos-
sible additional requirements. Comes standard with a Duo-Hitch™, a 2" Ball and
Lunette Eye combination hitch. Order:
K2636-1 Trailer
K2639-1 Fender & Light Kit
K2640-1 Cable Storage Rack
K903-1 SPARK ARRESTOR - Includes a heavy gage steel, approved spark
arrestor, clamp and adapter for mounting to the muffler exhaust pipe.
K704 ACCESSORY SET - Includes 35 ft. (10m) of electrode cable and 30 ft.
(9.1m) of work cable, head shield, work clamp electrode holder. Cables are
rated at 400 amps, 100% duty cycle.
K857 25 ft (7.6m) or K857-1 100 ft. (30.4m) REMOTE CONTROL
Portable control provides same dial range as the output control on the welder.
Has a convenient 6 pin plug for easy connection to the welder.
K802N POWER PLUG KIT
Provides four 120 volt plugs rated at 20 amps each and one dual voltage, full
KVA plug rated at 120/240 volts, 50 amps.
K802R POWER PLUG KIT
Provides four 120 volt plugs rated at 15 amps each and one dual voltage, full
KVA plug rated at 120/240 volts, 50 amps.
T12153-9 50 AMP, 120/240V POWER PLUG (1-Phase)
T12153-10 50 AMP, 240V POWER PLUG (3-Phase)
K1816-1 FULL KVA ADAPTER KIT
Plugs into the 120/240V NEMA 14-50R receptacle on the case front (which
accepts 4-prong plugs) and converts it to a NEMA 6-50R receptacle, (which
accepts 3-prong plugs.) For connection of Lincoln equipment with NEMA 6-50
Plug.
K1858-1 SERVICE INDICATOR KIT- Provides a GO / NO-GO visual indication of
air cleaner element useful service life. Filter service based on restriction readings
allows the longest life possible from the filter and best engine protection.
K2679-1 COLD WEATHER HEATER AND TARP KIT
For engine starting and operation in extreme cold weather conditions down to -
40ºF / -40ºC (with the use of OW40 synthetic oil and arctic diesel fuel), includes
120VAC engine block heater, and radiator grill tarp.
WIRE FEEDER OPTIONS
K449 LN-25 - Includes internal contactor for across the arc operation
(no control cable). Provides "cold" electrode until gun trigger is pressed.
Includes gas solenoid.
K1870-1 LN-15 Across the Arc Wire Feeder.
Portable, lightweight, compact CC/CV unit for flux-cored and MIG weld-
ing. Includes Gas Solenoid, adjustable flow meter and internal contactor.
For 10-15 lb. (4.5-6.8kg) spools.
Magnum Gun and Magnum Gun Connector Kit are required for gas-
shielded welding. Innershield Gun is required for gasless welding.
K126-2 Magnum 350 Innershield Gun
K1802-1 Magnum 300 MIG Gun (for LN-25)
K470-2 Magnum 300 MIG Gun (for LN-15, Includes Connector Kit)
K466-10 Connector Kit (for LN-15, K470-2)
K1500-1 Gun Receiver Bushing (for LN-15 & K126-2)
K487-25 Magnum SG Spool Gun
Hand held semiautomatic wire feeder. Requires SG Control Module and
Input Cable.
K488 SG Control Module (For Magnum Spool Gun)
The Interface between the power source and the spool gun. Provides
control of the wire speed and gas flow. For use with a K487-25 spool
gun.
K691-10 Input Cable (For SG Control Module)
For Lincoln engine power sources with 14-pin MS-type connection, sep-
arate 115V NEMA receptacles and output stud connections.
Note: See Wire Feeder IM manuals for appropriate Drive Roll and Guide
Tubes.
TIG OPTIONS
K1783-9 Pro -Torch® PTA-26V TIG Torch
Air Cooled 200 amp torch (2 piece) equipped with valve for gas flow
control. 25 ft. (7.6m) length.
KP509 Magnum Parts Kit for PTA-26V TIG Torch
Magnum Parts Kit provides all the torch accessories you need to start
welding. Parts kit provides collets, collet bodies, a black cap, alumina
nozzles and tungstens in a variety of sizes, all packaged in an easy to
carry reclosable sack.
K870 Foot Amptrol®
K963-3 Hand Amptrol®
K2347-1 Precision TIG 185 Ready-Pak(For AC TIG)
K2350-1 Invertec® V205-T AC/DC One-Pak™ Package
(For AC TIG)
PLASMA CUTTING
K1580-1 Pro-Cut 55
Cuts metal using the 3-phase AC generator power from the engine dri-
ven welder. Accepts 3-phase or 1-phase input power. Requires the
K1816-1 Full KVA adapter kit, if connected for 1-phase input
power.
C-1

ACCESSORIES