Vido.at AU-G65-SC18 User Manual page 12

6.OSD - Alarm Setting
Privacy Mask ( Window Blanking)
W I N DO W B L A NK I N G
Privacy Mask is used to protect the privacy area not to be
WINDOW NUMBER 01
displayed once the camera is pointed on, such asu
EDIT WINDOW
levatory area or the operation desk of an ATM machine. It
ENABLE WINDOW OFF
might be required for video surveillance application
CLEAR WINDOW
depends on the local law regulation. The G65 and G70
BACK
supports up to 24 private masks. ( depends on installed
EXIT
camera module, please contact your local sales
representative for more information)
Hitachi camera modules
Sony Camera modules:
the 45 series provides only 8)
LG,CNB Camera modules:
ALARMS
WINDOW NUMBER:
Resume OFF
SEQUENCE 001 EDIT WINDOW:
the keyboard. presse IRIS-OPEN to save.
RESET DELEY 030
ALARM CONTACT N/O
ENABLE WINDOW:
ALARM SETTING
CLEAR WINDOW:
ARM SETTING
BACK
EXIT
Alarms
RESUME: Continue the function on the camera , if it
ALARM SETTING
was setting before the alarms.
ALARM NUMBER 001
RESET DELAY: How long the camera stay in Alarm
position.
ALARM ACTION TOUR
ALARM CONTACT: Setting between N/C (normal
ACTIVATE AUX AUX1
Close) or N/O (normal Open).
ALARM PRIORITY LOW
ALARM NUMBER: curent Alarm number.
BACK
EXIT
ALARM ACTION: Setting for PRESET, SCAN, TOUR,
PAT 1-4, or NONE, if the camere in Alarm position.
ARM S ETTING
ACTIVATE AUX:
activate. Select between AUX1, AUX2 (not connected)
DAY SUN or BOTH.
ARM STATE OFF
ALARM PRIORITY:
ARM TIME N/A
UNARM TIME N/A
BACK
EXIT
ARM SETTING: define the operation timer of the alarm
19
Some products may not be available in your country, please contact our distributor for more details
: 8 masking area.
up to 24 masking area( except
no masking function.
Mask number
Edit position of the mask by joystick of
shows the mask on screen OFF
Delete the mask
Setting Alarm Output, when Alarm is
define the priority of the alarm input.
7. Dome Address & Protocol
Protocol setting
In order to establish a connection for
telemetric control with keyboard device. you
need to setup the dome address and protocol.
The G65 and G70 series are capable with
multiple communication protocol. The setting
can be changed through the DIP-Switches on
the rear side of the connector boards as
Illustrated.
Sw1 Sw2
please use the following table for details setup.
current pattern.
SW 1:
represent the domes address in binary form.
please refer to the list on next page for reference.
SW 2:
Used for protocol settting and baud rate.
DIP 1 to 6 : Protocol setting
DIP 7 and 8: Baud rate setting
Baud rate DIP 7 DIP8
2400 bps 0 0
4800 bps 1 0
9600 bps 0 1
19200 bps 1 1
Note: VIDO B02 Protocol is fully
compatible with VIDO B01. For
previous version of Vido products
please set to B02
Protocol / DIP 1 2 3 4 5 6
VIDO B02 0 0 1 1 0 0
DIAMOND 1 0 0 1 0 0
HUNDA 1 0 1 1 0 0
KALATEL 0 1 0 1 0 0
LILIN 1 1 0 1 0 0
MOLYNX 0 0 1 0 0 0
PANASONIC 1 1 1 0 0 0
PELCO (D/P) 1 0 0 0 0 0
PHILIPS 0 0 0 0 0 1
SAE 0 1 0 0 0 0
SAMSUNG 0 0 0 1 0 0
SANTACHI 0 1 1 0 0 0
UNIVISION 0 1 0 0 0 1
VCL 1 1 0 0 0 0
VICON 1 0 1 0 0 0
AD 0 0 1 1 0 0