CONTENTS GENERAL RECOMMENDATIONS............Pag. HANDLING ........................Pag. UNPACKING ........................Pag. DISPOSAL........................Pag. TECHNICAL DATA......................Pag. INSTRUCTIONS FOR THE INSTALLER/MAINTENANCE PERSON ..Pag. WATER CONNECTION ....................Pag. ELECTRICAL CONNECTION ..................Pag. WARNING MESSAGES DISPLAYED ON THE CONTROL PANEL ........ Pag. DETERGENT/RINSE-AID DISPENSERS AND SETTINGS..........Pag. SETTING THE DISPENSERS..................
GENERAL RECOMMENDATIONS Lift the appliance using a lift truck, remove the base WARNING and position the appliance CAREFULLY READ THE INSTALLATION, OPERAT- ING AND MAINTENANCE INSTRUCTIONS BEFORE INSTALLING THIS APPLIANCE. INCORRECT INSTALLATION, ADAPTATIONS ALTERNA- TIONS COULD CAUSE DAMAGE TO PROPERTY OR INJURY TO PERSONS.
TECHNICAL DATA MODEL LU7 / LU700 / WTU40 Supply voltage: 400...415- 3N~ - convertible to 220...240- 3~ - single-phase version 220...240 1N~ Frequency 50 or 60 Max. power input 9.9 / 12.1 (*) Boiler heating elements Tank heating elements Water supply press. for atmospheric boiler versions kPa [bar] 50...700 [0,5...7]...
Page 4
Fig. 4 Legend Fig. 4 A - Water inlet pipe with ø 3/4” G fittings C - Outlet pipe øi 40 mm (^) – øi 20 mm (*). - Power supply S - Pipe inlet for detergents Q - Unipotential screw (^) - Only for model with free-fall drainage (*) - Only for model with drain pump...
B INSTRUCTIONS FOR THE INSTALLER/MAINTENANCE PERSON Install a disconnecting switch with a capacity at pressure is too high, fit a suitable pressure least equal to that given in the technical data table, reducer on the inlet pipe. a 30mA residual current circuit breaker and an overcurrent device (magnetothermal cut-out with On the model with free-fall drainage: manual reset or fuse) between the appliance and...
Power supply 400…415V (standard Connections provided for energy control configuration) This appliance is designed for an external energy con- sumption control. Fig. 8 Open the power supply terminal board and insert the Fig. 11 jumpers provided as follows: one jumper between termi- Connect the energy peak controller across terminals 11 nals 2 and 4 and another between terminals 4 and 6.
Connections for automatic detergent dispenser C1..C8 CALL THE SERVICE CENTRE (Fig. 12) E1..E8 CALL THE SERVICE CENTRE The appliance continues to operate, but appropri- ate checks by a technician are recommended. DETERGENT/RINSE-AID DISPENSERS AND SETTINGS If the appliance is connected to a water softener or osmotic device, contact the detergent supplier for a specific product.
Display of programming mode: Initial amount of detergent: Fig. 14 Setting the activation time: • Connect the rinse-aid dispenser between termi- nals 8 and 9. These connection points are live dur- ing filling of the tank and at the end of the rinse cycle for a set time (see “setting the dispensers”...
• Completely drain the tank. the detergent dispenser only oper- • Remove and carefully clean the filters. ates during filling electrovalve operation for • Completely drain incorporated dispenser restoring the boiler level; terminals 7-9 of the main hoses, removing them from the containers. Repeat terminal board are powered at the same time.
INSTRUCTIONS FOR THE USER Our appliances have been studied and optimised to give high performance. This appliance must be used exclusively for the purpose for which it has been designed, i.e. for washing dishes with water and specific detergents. Any other use is to be considered improper.
To display the boiler temperature during heating of the - Cycle III tank, open the door and press the button “J” (Fig. 15). For very dirty dishes: press button “F” (Fig. 15) (see table of times). • To stop the wash cycle, just press the selected WASH CYCLES cycle button or open the door.
• BLUE rack for glasses: the glasses should be • Switch off the dishwasher by pressing button “A” placed upside down. (Fig. 15). • Switch off at the mains. • Close the water supply cock. • Replace the filter and the overflow. Fig.
FRONT LOADING DISHWASHER WITH How to fill the salt container INCORPORATED CONTINUOUS WATER • Switch off the dishwasher by pressing button “A” SOFTENER (Fig. 15). These models have a continuous softener in the dish- washer water circuit. By means of special resins, this device removes the calcareous substances from the feed water, supplying decalcified water for washing.
Rinse-aid container RESIDUAL RISKS In models with incorporated continuous water softener, The machine has several risks that were not com- the rinse-aid container is located in the front panel of pletely eliminated from a design standpoint or with the the appliance (Fig. 25). installation of adequate protection devices.
TROUBLESHOOTING DISHWASHER DOES NOT WASH 1. Check if the suction filter is dirty and clean it thoroughly. WELL 2. Check if the wash jets are clogged by solid food remains. 3. Check that the initial amount of detergent or subsequent additions are correct.