Related Manuals for Toro 30823
Summary of Contents for Toro 30823
- Page 1 Form No. 3350–961 Debris Blower 200 Series GroundsmasterR Model No. 30823—Serial No. 250000001 and Up Operator’s Manual English (EN, GB)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and Contents serial numbers of your product ready. The numbers can be found on a plate that is mounted on the blower housing. -
Page 3: Safety
Safety – Do not fill tank while engine is hot or running. – Do not smoke while handling gasoline. Safe Operating Practices – Fill fuel tank outdoors and up to about one inch from top of the tank, not the filler neck. Hazard control and accident prevention are dependent –... -
Page 4: Sound Pressure Level
– Set the parking brake and disengage the PTO. purchase genuine TORO replacement parts and accessories to keep the Toro all TORO. NEVER USE – Shut the engine off and remove the key from the “WILL–FIT” REPLACEMENT PARTS AND ignition switch. -
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-6674 1. Crushing hazard, hand—read the instructions before servicing or performing maintenance. -
Page 6: Specifications
98-3114 98-3137 1. Entanglement hazard—stay away from moving parts. 1. Read the Operator’s 2. Grease Manual. 3. Grease every 8 hours. 98-3115 1. Rotating shaft 98-3112 1. Warning—read the instructions before servicing or performing maintenance on the electrical wiring. Specifications Blower Specifications Backward curved, cast aluminum fan. -
Page 7: Setup
70001 or prior and is equipped with old style bracket, part no. 92–9786, a new bracket must be obtained from your Toro Distributor. 1. Park the machine on a level surface, lower the cutting unit to the floor, engage the parking brake, be sure the... -
Page 8: Install Castor Wheel Assemblies
9. Install wheel and tire assembly. Torque wheel nuts to 3. Assure both castor wheels are set at same height. 45–55 ft–lbs. Install Stand 10. Repeat procedure on left side of machine. Note: Install drive shaft to traction unit before installing 1. -
Page 9: Install Drive Shaft
ANSI B71.4–1990 Standard when (4) 35 lb. weights are Install Drive Shaft installed. Order two Weight Kits, Part No. 24–5780 from your Toro Distributor. 1. Remove (3) capscrews, (6) washers and (3) nuts securing belt guard to blower frame (Fig. 5). -
Page 10: Operation
Operation Adjust Discharge Opening The discharge opening is adjustable to increase or decrease air output velocity and volume. Decreasing discharge Operating Tips opening size will increase velocity. 1. Loosen discharge opening deflector mounting screws Warning (Fig. 6). Discharged air has considerable force and could cause injury or loss of footing. -
Page 11: Maintenance
Maintenance The (2) mount frame pivots (Fig. 9) must be lubricated after every 8 hours of operation with a No. 2 Lithium based grease. Lubrication The Idler arm bearing (Fig. 7) must be lubricated after every 8 hours of operation with a No. 2 Lithium based grease. -
Page 12: Adjusting Blower Belt
Adjusting Blower Belt 3. When belt stretches it can be adjusted as follows: A. Loosen nut securing belt tensioner to blower Make sure belt is properly tensioned to assure proper housing (Fig. 13). operation of the machine and unnecessary wear. Check belt frequently. -
Page 13: Troubleshooting
Troubleshooting Problem Possible Causes Corrective Action Fan quit turning 1. Belt may be loose or broken. 1. Replace belt or adjust the tension of the belt. 2. Bearing pressed in the bearing 2. Replace the bearing, use #609 mount may be damaged. Loctite when replacing. -
Page 14: Storage
Storage Thoroughly clean the blower. The fan housing should be free of dirt, leaves and debris. Lubricate all grease fittings. Wipe off any excess lubricant. Place a light coat of grease on the splines of the PTO adapter. Tighten all fasteners. -
Page 16: The Toro General Commercial Products Warranty
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.