Related Manuals for Toro 30393
Summary of Contents for Toro 30393
- Page 1 Form No. 3388-972 Rev A Debris Blower Groundsmaster ® 7200/7210 Traction Unit Model No. 30393—Serial No. 315000001 and Up *3388-972* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
You are responsible for operating the product properly and safely. Safety ................3 Before Operating ............ 3 You may contact Toro directly at www.Toro.com for product While Operating............3 and accessory information, help finding a dealer, or to register Maintenance ............3 your product. -
Page 3: Safety
A free replacement manual is available by sending the • Do not operate the machine under the influence of complete Model and Serial Number to The Toro® alcohol or drugs. Company, 8111 Lyndale Avenue South, Bloomington, Minnesota 55420-1196. -
Page 4: Safety And Instructional Decals
Toro replacement parts and accessories hydraulic system, all pressure in the system must be to keep the machine all Toro. Never use “will-fit” relieved by stopping the engine and lowering the blower replacement parts and accessories made by other to the ground. - Page 5 105-4593 1. Entanglement hazard, shaft—do not remove cover while parts are moving, keep all guards in place. 114–4054 1. Warning—read the Operator’s Manual, do not operate the machine without the cross pin in place.
-
Page 6: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Mount the castor wheel. Debris blower assembly Mount the debris blower to the traction Locking pin unit. Hair pin cotter –... -
Page 7: Mounting The Debris Blower To The Traction Unit
3. Make sure the castor wheel assembly tire is inflated to 5. Insert the locking pin through the adapters and secure 35 to 50 psi. with a hairpin cotter (Figure 5). Mounting the Debris Blower to the Traction Unit Parts needed for this procedure: Debris blower assembly Locking pin Hair pin cotter... -
Page 8: Greasing The Blower
Installing the Front Weight No Parts Required Procedure CAUTION When an attachment is not installed on the machine, loose weights must be removed. Never operate the machine with no attachment installed and front weights on the machine. Use the following weight charts to determine the correct amount of front weight required for your machine. - Page 9 72-inch width of cut Groundsmaster 7200/7210 with NO hard canopy Additional front weight Attachment Weight part number(s) Weight description required Rear QAS and no 0 kg (0 lb) attachment (Model 30377) QAS finish grader / box 0 kg (0 lb) rake (Model 08754) Steel drag mat (Model 0 kg (0 lb)
- Page 10 62-inch width of cut Groundsmaster 7200/7210 with NO hard canopy Additional front weight Attachment required Weight part number(s) Weight description Rear QAS and no 30.4 kg (67 lb) 114-4090 and front weight bracket and attachment (Model 114-4096 19 kg (42 lb) front weight 30377) 114-4090 and QAS finish grader / box...
-
Page 11: Product Overview
A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. G003812 Figure 7 1. -
Page 12: Operating Tips
Figure 8 1. Float 3. Lift/Lower 2. Power-down Operating Tips G003783 WARNING Figure 9 Discharged air has considerable force and could cause injury or loss of footing. 1. Pry slot • Stay away from discharge opening when machine is operating. •... -
Page 13: Maintenance
Maintenance Greasing the Attachment Adapter If the locking lever on the attachment adapter does not pivot Lubrication freely and easily, apply a light coat of grease to the area shown in Figure 12. The debris blower has bearings and bushings that must be lubricated regularly. -
Page 14: Torquing Fasteners
G003815 Figure 14 1. Motor coupler 3. Set screw (2 each) G003817 2. Fan coupler 4. Coupler spider Figure 16 1. Fan mounting nut 3. Tighten the capscrews and the nuts securing the mounting brackets together and to the blower housing. 4. -
Page 15: Servicing The Castor Wheels And Bearings
Figure 17 1. Bushings 2. Castor arm tube Figure 18 1. Locknut 4. Castor fork 5. Apply grease to the inside and outside of the new 2. Washer 5. Castor wheel bushings. Using a hammer and flat plate, drive the 3. - Page 16 Notes:...
- Page 17 Notes:...
- Page 18 Notes:...
- Page 19 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.