Vitek Winx Club WX 4001 MS Manual Instruction page 6

ENGLISH
4. To move to the previous or to the next track,
if the playback is stopped, press the
buttons once.
Moving to a certain fragment of the disc
Press and hold the
the certain fragment of the track in the forward or
backward direction (Sound will not be played back
until the / buttons are pressed). Press and hold
the -10/FOL- or +10/FOL+ button on the remote
control to move to the previous/next folder.
Use the / buttons to select the desired track
in the selected folder.
Repeated playback of a track or a disc
1. To repeat one track press the REP/RAN but-
ton once, "REP" will appear on the LCD-dis-
play.
2. To repeat all tracks on the disc press the REP/
RAN button twice, "REP ALL" will appear on
the LCD-display
3. To repeat the album press the REP/RAN but-
ton thrice, "REP ALBUM" will appear on the
LCD-display
Note: These functions are active only in the
playback or pause mode.
Random playback
1. To random playback all tracks on the disc,
press the REP/RAN button four times in the
playback mode, "PLAY RANDOM" will appear
on the LCD-display.
2. To cancel random playback of all tracks, press
the REP/RAN button once again, "PLAY RAN-
DOM" will disappear from the LCD-display.
Note: These functions are active only in the
playback or pause mode.
PROGRAMMING THE PLAYBACK
You can program playback of tracks in the de-
sired order.
In the CD or MP3-disc playback mode:
1. When the playback of a disc is stopped, press
the PROG button once. "PROGRAM", track
number "P01" will appear on the LCD-dis-
play.
2. Select the desired track, consequently press-
ing the or buttons.
3. To store the selected track press the PROG
button. The number of the track will change
to "Р02".
4001Instruk_ital.indd 6 4001Instruk_ital.indd 6
/
/ buttons to quickly move to
4. Programming of the next track: select the next
track, consequently pressing the
tons. Then press the PROG button to store
the selected track in memory.
5. To playback programmed tracks, press the
PLAY/PAUSE button.
6. To cancel programmed playback mode press
the STOP button or open the disc slot lid, or
set the FUNCTION switch to another position.
Note: You can program up to 99 tracks.
Playback of МР3 files from a USB-device
This unit can playback most of MP3 discs but
there are cases when the disc is not played back
due to the settings of the software used for re-
cording this disc. (For instance, if the finalization
of a disc is absent.)
1. Switch on the unit. Set the FUNCTION switch
to the AUX(MP3) position.
2. Press and hold the PLAY/PAUSE button on
the unit to move to the USB mode.
3. Insert a USB device into the corresponding
jack. The reading will start, and then total
number of tracks will appear on the display.
4. If a USB device is not connected to the USB
jack, "NOd" will appear on the LCD-display.
5. To exit the USB mode, press and hold the
PLAY/PAUSE button.
6. To move 10 tracks forward or backward,
press and hold the -10/FOL- and +10/FOL+
buttons (to select album press and hold the
buttons).
7. Use the or buttons to select the desired
track.
8. Press and hold the
speed playback in the forward or backward
direction.
9. Press the PLAY/PAUSE button to playback
the selected track.
10. Press the PLAY/PAUSE button to pause play-
back.
11. To resume playback press the PLAY/PAUSE
button once again.
12. To stop playback press the STOP button.
Note: This unit does not support playback
from HDD discs and some MP3 players.
Repeated playback of a track or a folder (al-
bum)
1. To repeat one track press the REP/RAN but-
ton once in the USB mode, the current track
will be constantly repeated.
6
or but-
/ buttons for increased
22.08.2011 12:00:51 22.08.2011 12:00:51