Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for iSolution iMove 350 Beam
Summary of Contents for iSolution iMove 350 Beam
- Page 1 User M anual ...
-
Page 2: Table Of Contents
CONTENTS 1. S afety I nstruction .....................2 2. T echnical S pecifications....................3 3. H ow T o S et T he U nit....................4 3.1 C ontrol P anel ......................4 3.2 ... -
Page 3: S Afety I Nstruction
1. S afety I nstruction Please r ead t he i nstruction c arefully w hich i ncludes i mportant information a bout t he i nstallation, u sage a nd m aintenance. WARNING ... -
Page 4: T Echnical S Pecifications
moisture. The h ousing a nd t he l enses m ust b e r eplaced i f t hey a re v isibly d amaged. Installation: ... -
Page 5: H Ow T O S Et T He U Nit
3. H ow T o S et T he U nit 3.1 C ontrol P anel 1. F unction D isplay: Shows ... -
Page 6: M Ain F Unction
UP To g o f orward i n t he s elected f unctions ENTER To c onfirm t he s elected f unctions 4. ... - Page 7 ...
- Page 8 DMX A ddress To select the DMX Address, press the ENTER button to show DMX ADDRESS on the display. Use the DOWN/UP buttons to adjust the address from 001 to 512. Once the address has been selected, ...
- Page 9 Slave M ode To select the Slave Mode, press the ENTER button to show SLAVE MODE on the display. Use the DOWN a nd U P b uttons t o s elect t he S lave 1 o r S lave 2 m ode. O nce t he m ode h as b een s elected, press ...
- Page 10 Pan I nverse To select the Pan Inverse, press the ENTER button to show PAN INVERSE on the display. Use the DOWN a nd U P b uttons t o s elect t he Yes ( pan i nversion) o r N o ( normal) m ode. O nce t he m ode h as been ...
- Page 11 MENU button again. Press and hold the MENU button for about one second or wait for one minute t o e xit t he m enu m ode. ...
- Page 12 minute t o e xit t he m enu m ode. Firmware V ersion To select the Firmware Version, press the ENTER button to show FIRMWARE VERSION on the display and the display will show the version of software of the unit. To go back to the functions ...
-
Page 13: H Ome P Osition A Djustment
Press the ENTER button and the corresponding functions will be set to the defaults setting, to go back to the functions without any changes press the MENU button again. Press and hold the MENU ... -
Page 14: H Ow T O C Ontrol T He U Nit
Press t he M ENU b utton t o e xit. TILT O FFSET — Tilt h ome p osition a djustment To s elect t he T ilt O ffset, p ress t he E NTER b utton t o s how T ILT O FFSET o n t he d isplay. U se t he DOWN ... -
Page 15: M Aster/Slave B Uilt I N P Re--Program F Unction
to their ‘home’ position and you may hear some movement noises for about 20 seconds. After that t he u nit w ill b e r eady t o r eceive a D MX s ignal o r r un t he b uilt i n p rograms. ... -
Page 16: D Mx C Ontroller
(LED O FF) (LED S low B linking) 4.3 D MX C ontroller By u sing a u niversal D MX c ontroller t o c ontrol t he u nits, y ou n eed t o s et a D MX a ddress f rom 1 t o 512 ... -
Page 17: D Mx512 C Onfiguration
5. D MX512 C onfiguration 8 C hannels M ode: ... - Page 18 11 C hannels M ode: ...
-
Page 19: D Mx C Onnection
6. D MX C onnection Unit 1 Unit 2 Unit 3 Unit 4 ... -
Page 20: T Roubleshooting
7. T roubleshooting Following a re a f ew c ommon p roblems t hat m ay o ccur d uring o peration. H ere a re s ome suggestions ... -
Page 21: F Ixture C Leaning
8. F ixture C leaning The c leaning m ust b e c arried o ut p eriodically t o o ptimize l ight o utput. C leaning f requency depends ... - Page 22 ...
- Page 23 Declaration o f C onformity We d eclare t hat o ur p roducts ( lighting e quipments) c omply w ith t he following ...
- Page 24 Innovation, Q uality, P erformance ...
Need help?
Do you have a question about the iMove 350 Beam and is the answer not in the manual?
Questions and answers