Convection Motor Removal; Turntable Motor Removal - Viking VHSO205SS Service Manual

mounting angle to the bottom plate from under the bottom
plate.
30. R emove the thirteen (13) screws holding the convection
duct to the oven cavity and the heater duct upper.
31. R emove the convection duct assembly from the oven
1. Disconnect the power supply cord.
. Remove the outer case cabinet, referring to "OUTER
CASE CABINET REMOVAL".
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to "BACK
PLATE REMOVAL".
6. Remove the heater duct left assembly from the oven cavity,
referring to "HEATER DUCT LEFT ASSEMBLY, HEATER
1. Disconnect the power supply cord.
. Remove the outer case cabinet, referring to "OUTER
CASE CABINET REMOVAL".
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to "BACK
PLATE REMOVAL".
6. Remove the convection duct assembly from the oven
cavity, referring to "HEATER DUCT LEFT ASSEMBLY,
HEATER D UCT U PPER A SSEMBLY A ND C ONVECTION
DUCT ASSEMBLY REMOVAL
1. Disconnect the power supply cord.
. Remove the outer case cabinet, referring to "OUTER
CASE CABINET REMOVAL".
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to "BACK
PLATE REMOVAL".
6. Remove the heater duct left assembly from the oven cavity,
referring to "HEATER DUCT LEFT ASSEMBLY, HEATER
1. Disconnect the power supply cord.
. Wait for 60 seconds to discharge the high voltage
capacitor.
3. Remove the turntable tray and the turntable support from
the oven cavity.
4. Lay the oven on its backside.
5. Remove the turntable motor cover by snipping off the
material in four corners.
6. Where the corners have been snipped off, bend corner
areas flat. No sharp edges must be evident after removal
of the turntable motor.
DOOR SENSING SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH
Removal
1. Disconnect the power supply cord.
3. N ow, the convection duct assembly is free.
33. R emove the nine (9) screws holding the heater duct
34. R emove the heater duct upper from the oven cavity.
35. N ow, the heater duct upper assembly is free.
SIDE HEATING ELEMENT REMOVAL
7. Remove the one (1) screw holding the heater mounting
8. Remove the two () nuts holding the side heating element
9. Now, the side heating element is free.

CONVECTION MOTOR REMOVAL

7. Loosen the one (1) screw holding the convection fan
8. Remove the four (4) screws holding the convection motor
9. Remove the six (6) screws holding the convection motor
10. R emove the convection motor from the convection motor
11. N ow, the convection motor is free.
TOP HEATING ELEMENT REMOVAL
7. Remove the one (1) screw holding the heater mounting
8. Remove the two () nuts holding the top heating element
9. Now, the top heating element is free.

TURNTABLE MOTOR REMOVAL

7. Disconnect the wire leads from the turntable motor.
8. Remove the one (1) screw holding the turntable motor
9. Now, the turntable motor is free.
10. A fter replacement, use the one (1) screw to fit the turntable
REPLACEMENT
. Remove the outer case cabinet, referring to "OUTER
37
cavity.
upper to the oven cavity.
DUCT UPPER ASSEMBLY AND CONVECTION DUCT
ASSEMBLY REMOVAL
angle B to the heater duct left.
to the heater duct left.
assembly to the convection fan motor shaft with a hexagon
key wrench, and remove the convection fan.
mounting angle to the convection duct.
to the convection motor mounting angle.
mounting angle.
DUCT UPPER ASSEMBLY AND CONVECTION DUCT
ASSEMBLY REMOVAL
angle A to the heater duct upper.
to the heater duct upper.
to the oven cavity bottom plate.
motor cover.
CASE CABINET REMOVAL".
VHSO205SS