Door Disassembly - Viking VHSO205SS Service Manual

5. Close the door.
6. Remove the two () door springs from the door cam right,
oven hinge right, door com left and oven hinge left.
7. Release the door cams right and left from the right and
left door cam pins of the door.
8. Remove the door cams right and left from the oven cavity
front plate.
9. Open the door assembly at an angle of more than 90½
with the oven cavity front plate.
10. T o release the right and left door hinge pins of the door
assembly from the oven hinges right and left, slide the door
assembly leftward. When removing the door assembly,
hold the door assembly to prevent it from falling.
11. N ow, the door assembly is free.
NOTE: When the individual parts are replaced, refer to

"Door Disassembly"

Door assembly reinstallation
1. On reinstalling the door assembly, insert the oven hinges
right and left into the right and left door hinge pins.
. Insert and hook the door cams right and left to the right
and left door cam pins.
3. Reinstall the two () door springs between the door cams
and the oven hinges right and left.
NOTE: After any service to the door;
(A) Make sure that the door sensing switch and the
secondary interlock switch are operating properly.
(Refer to chapter "Test Procedure".)
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
Door adjustment
When removing and/or loosening the oven hinges such as
in door replacement, the following adjustment criteria are
taken.
Door adjustment is performed with the door properly installed
and closed and while the oven hinges are loose.
1. Loosen the screws holding the oven hinge right and the
oven hinge left to the bottom plate with screwdriver.
. Adjust the door by moving it so that the door is parallel
with the oven cavity front plate lines (right and left side
lines) and the door latch heads pass through the latch
holes correctly.
3. Tighten the screws holding the oven hinge right and the
oven hinge left to the bottom plate.
After adjustment, make sure of the following:
1. The door latch heads smoothly catch the latch hooks
through latch holes and the latch heads goes through
center of latch holes.
1. Disconnect the power supply cord.
. Remove the outer case cabinet, referring to "OUTER
CASE CABINET REMOVAL".
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the door assembly, referring to "Door
Replacement".
. The door is positioned with its face pressed toward oven
cavity front plate.
3. Reinstall the outer case cabinet and check for microwave
leakage around the door with an approved microwave
survey meter. (Refer to Microwave Measurement
Procedure.)
NOTE: The door on a microwave oven is designed to act
as an electronic seal preventing the leakage of
microwave energy from the oven cavity during
cook cycle. This function does not require that the
door be airtight, moisture (condensation)-tight
or light-tight. Therefore, occasional appearance
of moisture, light or sensing of gentle warm air
movement around the oven door is not abnormal
and do not of themselves indicate a leakage of
microwave energy from the oven cavity. If such
were the case, your oven could not be equipped
with a vent, the very purpose of which is exhaust
the vapor-laden air from the oven cavity.
Door spring
Oven hinge
left
Left door
hinge pin
DOOR DISASSEMBLY
6. Place the door assembly on a soft cloth with latch heads
facing up.
NOTE: As the engaging parts of the choke cover and the
door panel assembly are provided at 16 places,
do not force any particular part.
7. Replacement of the door components are as follows:
39
Door cam left
Door
assembly
Figure C-4(a). Door Replacement
Left door
cam pin
Door cam left
Oven hinge
left
Door
assembly
Right door
hinge pin
Figure C-4(b). Door Replacement
VHSO205SS
Door cam right
Door
spring
Oven hinge
right
Right door
cam pin
Door cam right
Oven hinge
right