Using The Wall-Mounted Door Control; To Open The Door Manually - Craftsman 139.18489D Owner's Manual

Using the Wall-Mounted
Door Control
THE MOTION DETECTING CONTROL
CONSOLE
Press the lighted push button to open or
close the door. Press again to reverse
the door during the closing cycle or to
stop the door while it's opening.
This door control contains a motion
detector that will automatically turn on
the light when it detects a person entering the garage. This
feature can be easily turned off for extended work light
use.
Light feature
Press the Light button to turn the opener light on or off. It
will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the
light will remain on for 4-1/2 minutes. Press again to turn it
off sooner. The 4-1/2 minute interval can be changed to
1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold
the Lock button until the light blinks (about 10 seconds). A
single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
Automatic Light Feature: The opener light will turn on
automatically when a person enters the garage. When a
person walks in front of the door control, the light will come
on for five minutes, then shut off. This feature works by
detecting body heat and may not work in temperatures
around 100˚F (37.7˚C).
To disable this feature, slide the Detector Switch on the
right side of the door control down (off).
We recommend that you disable the motion sensor when
using the opener lights as working lights. Otherwise, they
will turn off automatically if you are working beyond the
sensors range.
Lock feature
Designed to prevent operation of the door from hand-held
remote controls. However, the door will open and close
from the Door Control, the Outdoor Key Switch and the
Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
The push button light will flash as long as the Lock feature
is on.
To turn off, press and hold the Lock button again for
2 seconds. The push button light will stop flashing. The
Lock feature will also turn off whenever the "learn" button
on the motor unit panel is activated.
Additional feature when used with the 3-Function
hand-held remote
To control the opener lights:
In addition to operating the door, you
Push
may program the remote to operate the
Bar
lights.
Lock
1. With the door closed, press and hold a small remote
Button
button that you want to control the light.
Light
Button
2. Press and hold the Light button on the door control.
3. While holding the Light button, press and hold the Lock
button on the door control.
4. After the opener lights flash, release all buttons.

To Open the Door Manually

To prevent possible SERIOUS INJURY or DEATH from a falling
garage door:
• If possible, use emergency release handle to disengage
trolley ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If rope knot
becomes untied, you could fall.
DISCONNECT THE TROLLEY:
The door should be fully closed if
possible. Pull down on the
emergency release handle (so
that the trolley release arm snaps
into a vertical position) and lift
the door manually. The lockout
feature prevents the trolley from
reconnecting automatically, and
the door can be raised and
lowered manually as often as
necessary.
TO RE-CONNECT THE TROLLEY:
Pull the emergency release
handle toward the opener at an
angle so that the trolley release
arm is horizontal. The trolley will
reconnect on the next UP or
DOWN operation, either
manually or by using the door
control or remote.
31
Trolley
Trolley
Release Arm
(In Manual
Disconnect
Position)
Lockout position
(Manual disconnect)
Trolley
Trolley
Release
Arm
Emergency
Release Handle
(Down and Back)
To reconnect