Table of Contents

Advertisement

Available languages

Available languages

Owner's Manual
1/2 HP
GARAGE DOOR OPENER
For Residential Use Only
Models • 139.18451DM • 139.18452DM • 139.18453DM • 139.18473DM • 139.18490DM
Read and follow all safety rules and
operating instructions before first use
of this product.
Fasten the manual near the garage
door after installation.
Periodic checks of the opener are
required to ensure safe operation.
Sears Canada, Inc., Toronto, Ontario M5B 2B8
®
Safety Precautions
Assembly
Installation
Adjustment
Maintenance
Operation
Troubleshooting
Parts List

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman 139.18451DM

  • Page 1 Owner’s Manual ® 1/2 HP GARAGE DOOR OPENER For Residential Use Only Models • 139.18451DM • 139.18452DM • 139.18453DM • 139.18473DM • 139.18490DM Read and follow all safety rules and Safety Precautions ■ operating instructions before first use Assembly ■...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Introduction Adjustment 27-29 Safety symbol and signal word review ....2 Adjust the travel limits ..... . 27 Preparing your garage door .
  • Page 3: Preparing Your Garage Door

    Preparing your garage door Before you begin: To prevent possible SERIOUS INJURY or DEATH: • Disable locks. • ALWAYS call a trained door systems technician if garage door • Remove any ropes connected to garage door. binds, sticks, or is out of balance. An unbalanced garage door •...
  • Page 4: Planning

    Planning SECTIONAL DOOR INSTALLATIONS Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your • Do you have a steel, aluminum, fi berglass or glass panel installation.
  • Page 5: Planning

    Planning (Continued) ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons • Generally, a one-piece door does not require reinforcement. (particularly small children) could be SERIOUSLY INJURED or If your door is lightweight, refer to the information relating to KILLED by a closing garage door.
  • Page 6: Carton Inventory

    Carton Inventory Your garage door opener is packaged in one carton which contains check the packing material. Hardware for assembly and installation the motor unit and all parts illustrated below. Accessories will is shown on the next page. Save the carton and packing material depend on the model purchased.
  • Page 7: Hardware Inventory

    Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Lock Nut Lock Washer 3/8" Washer 5/8" Nut 3/8" 1/4"-20 Chain Extension Link Parts Bolt 1/4"-20x2-1/2 Idler Bolt Master Link (2) Spacer (2) Trolley Threaded Shaft INSTALLATION HARDWARE Ring...
  • Page 8: Assembly

    ASSEMBLY STEP 1 Assemble the Rail & Install the Trolley To prevent INJURY from pinching, keep hands and fi ngers To avoid installation diffi culties, do not run the garage door away from the joints while assembling the rail. opener until instructed to do so. The front rail has a cut out “window”...
  • Page 9 ASSEMBLY STEP 2 Fasten the Rail to the Motor Unit To avoid SERIOUS damage to garage door opener, use ONLY 1. Insert a 1/4"-20x2-1/2 bolt, washer and spacer into the cover those bolts/fasteners mounted in the top of the opener. protection bolt hole on the back end of the rail as shown.
  • Page 10: Install The Chain/Cable

    ASSEMBLY STEP 4 Install the Chain/Cable To avoid possible SERIOUS INJURY to fi ngers from moving 1. Pull the cable around the idler pulley and toward the trolley. garage door opener: 2. Connect the cable to the retaining slot on the trolley, as shown •...
  • Page 11: Tighten The Chain

    ASSEMBLY STEP 5 Tighten the Chain Figure 1 1. Spin the inner nut and lock washer down the trolley threaded Trolley shaft, away from the trolley. Outer Lock Threaded Washer Shaft 2. To tighten the chain, turn outer nut in the direction shown To Tighten Outer Nut (Figure 1).
  • Page 12: Determine The Header Bracket Location

    Unfinished INSTALLATION STEP 1 Ceiling OPTIONAL Determine the Header Bracket Location CEILING MOUNT HEADER BRACKET Header Wall To prevent possible SERIOUS INJURY or DEATH: Vertical Centerline • Header bracket MUST be rigidly fastened to structural of Garage Door support on header wall or ceiling, otherwise garage door Structural might NOT reverse when required.
  • Page 13: Install The Header Bracket

    Wall Mount INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall.
  • Page 14: Attach The Rail To The Header Bracket

    INSTALLATION STEP 3 Attach the Rail to the Header Bracket 1. Position the opener on the garage fl oor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring.
  • Page 15: Position The Opener

    INSTALLATION STEP 4 Position the Opener To prevent damage to garage door, rest garage door opener Follow instructions which apply to your door type as illustrated. rail on 2x4 placed on top section of door. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid fl...
  • Page 16: Hang The Opener

    INSTALLATION STEP 5 Hang the Opener To avoid possible SERIOUS INJURY from a falling garage Three representative installations are shown. Yours may be door opener, fasten it SECURELY to structural supports of different. Hanging brackets should be angled (Figure 1) to provide the garage.
  • Page 17: Install The Door Control

    INSTALLATION STEP 6 Install the Door Control To prevent possible SERIOUS INJURY or DEATH from Locate door control within sight of door, at a minimum height electrocution: of 5 feet (1.5 m) where small children cannot reach, away from • Be sure power is NOT connected BEFORE installing door moving parts of door and door hardware.
  • Page 18: Install The Light

    INSTALLATION STEP 7 Install the Light To prevent possible OVERHEATING of the endpanel or light 1. Press the release tabs on both sides of lens. Gently rotate lens socket: back and downward until the lens hinge is in the fully open •...
  • Page 19: Electrical Requirements

    INSTALLATION STEP 9 Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from To avoid installation diffi culties, do not run the opener at this electrocution or fi re: time. • Be sure power is NOT connected to the opener, and To reduce the risk of electric shock, your garage door opener has disconnect power to circuit BEFORE removing cover to a grounding type plug with a third grounding pin.
  • Page 20: Install The Protector System

    INSTALLATION STEP 10 Install The Protector System ® Be sure power is NOT connected to the garage door opener The safety reversing sensor must be connected and aligned BEFORE installing the safety reversing sensor. correctly before the garage door opener will move in the down To prevent SERIOUS INJURY or DEATH from a closing garage direction.
  • Page 21 INSTALLING THE BRACKETS Figure 1 DOOR TRACK MOUNT (RIGHT SIDE) Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage Door door, with the beam no higher than 6" (15 cm) above the fl oor. Track They may be installed in one of three ways, as follows.
  • Page 22 MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Figure 5 1. Slide a 1/4"-20x1/2" carriage bolt head into the slot on each Wing Nut sensor. Use wing nuts to fasten sensors to brackets, with 1/4"-20 lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5).
  • Page 23: Fasten The Door Bracket

    INSTALLATION STEP 11 Fasten the Door Bracket Fiberglass, aluminum or lightweight steel garage doors WILL Follow instructions which apply to your door type as illustrated REQUIRE reinforcement BEFORE installation of door bracket. below or on the following page. Contact your door manufacturer for reinforcement kit. A horizontal reinforcement brace should be long enough to be secured to two vertical supports.
  • Page 24 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.
  • Page 25 INSTALLATION STEP 12 Connect Door Arm to Trolley Pulley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY • Make sure garage door is fully closed. Pull the emergency Outer release handle to disconnect the outer trolley from the inner Inner Trolley...
  • Page 26: Connect The Door Arm To The Trolley

    ALL ONE-PIECE DOORS Figure 5 CORRECT INCORRECT 1. Assemble the door arm, Figure 5: Straight IMPORTANT: The groove on the straight door arm MUST face Straight Door Arm Door Arm away from the curved door arm. Curved • Fasten the straight and curved door arm sections together (Groove Curved Door...
  • Page 27: Adjustment

    ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Without a properly installed safety reversal system, persons Limit adjustment settings regulate the points at which the door (particularly small children) could be SERIOUSLY INJURED or will stop when moving up or down. KILLED by a closing garage door.
  • Page 28: Adjust The Force

    ADJUSTMENT STEP 2 Adjust the Force Without a properly installed safety reversal system, persons Force adjustment controls are located on the back panel of the (particularly small children) could be SERIOUSLY INJURED or motor unit. Force adjustment settings regulate the amount of KILLED by a closing garage door.
  • Page 29: Test The Safety Reversal System

    ADJUSTMENT STEP 3 Test the Safety Reversal System Without a properly installed safety reversal system, persons TEST (particularly small children) could be SERIOUSLY INJURED or 1. With the door fully open, place a 1-1/2" (3.8 cm) board KILLED by a closing garage door. (or a 2x4 laid fl...
  • Page 30: Operation

    WARNING OPERATION IMPORTANT SAFETY INSTRUCTIONS WARNING WARNING To reduce the risk of SEVERE INJURY or DEATH: READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS. If one control (force or travel limits) is adjusted, the other control may also need adjustment. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door 10.
  • Page 31: Using The Wall-Mounted Door Control

    Using the Wall-Mounted Door Control To Open the Door Manually Lighted Press the lighted push button to open or Push Button close the door. Press again to reverse the door during the closing cycle or to stop the To prevent possible SERIOUS INJURY or DEATH from a falling door while it's opening.
  • Page 32 THE REMOTE CONTROL BATTERY Care of Your Opener LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some FORCE CONTROLS minor changes in door operation To prevent possible SERIOUS INJURY or DEATH: requiring some re-adjustments, • NEVER allow small children near batteries. particularly during the fi...
  • Page 33: Having A Problem

    Having a Problem? 1. My door will not close and the light bulbs blink on my motor Bell Wire unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. •...
  • Page 34: Diagnostic Chart

    Bell Wire Installed Safety Reversing Diagnostics Sensor Located On Motor Unit Your garage door opener is programmed with self-diagnostic LED or capabilities. The “Learn” button/diagnostic LED will fl ash a number Diagnostic of times then pause signifying it has found a potential issue. Consult “Learn”...
  • Page 35: Programming

    PROGRAMMING NOTICE: If this Security ✚ ® garage door opener is operated with a non-rolling code transmitter, the technical measure in the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code transmitter to circumvent that technical measure.
  • Page 36: To Add, Reprogram Or Change A Keyless Entry Pin

    To Add, Reprogram or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener. USING THE “LEARN” BUTTON To set a temporary PIN You may authorize access by visitors or service people with a temporary 4-digit PIN.
  • Page 37: Repair Parts

    REPAIR PARTS Rail Assembly Parts PART DESCRIPTION 4A1008 Master link kit 41C5141-1 Complete trolley assembly 41A5665 Complete rail 144C56 Idler pulley 41A5807 Chain and cable 12D598-1 “U” bracket NOT SHOWN 183A163 Wear pads Installation Parts PART DESCRIPTION 41A4899 Standard control console 41A4166 Door control button 10A20...
  • Page 38: Motor Unit Assembly Parts

    Motor Unit Assembly Parts (Down) LIMIT SWITCH Brown Contact ASSEMBLY Wire Grey Wire Drive Gear Center Limit (Up) Yellow Contact Contact Wire PART PART DESCRIPTION DESCRIPTION 41A5615 Chain Spreader 41A5525-28 Cover 41C4220A Gear and sprocket assembly 41A2818 Limit switch drive & retainer Complete with: Spring washer, 41D3452 Limit switch assembly...
  • Page 39: Accessories

    CRAFTSMAN GARAGE DOOR OPENER LIMITED WARRANTY GENERAL: Craftsman garage door openers (“GDO”) are warranted to be free from defects in materials or workmanship for a specifi c time period as set-out below (the “Warranty Period”). Warranties extend to the original purchaser of a Craftsman product only and is non-transferable. Purchases made through an online auction or through any website other than www.sears.ca are excluded.
  • Page 40 ® Registered Trademark / ™ Trademark / Service Mark of Sears, Roebuck and Co. ® Marca Registrada / ™ Marca de Fábrica / Marca de Servicio de Sears, Roebuck and Co. Marque de commerce / Marque déposée de Sears, Roebuck and Co. 114A3608E ©...
  • Page 41 Manuel d’instructions ® 1/2 HP OUVRE-PORTE DE GARAGE Pour résidences seulement Modèles • 139.18451DM • 139.18452DM • 139.18453DM • 139.18473DM • 139.18490DM Consignes de sécurité Lire attentivement ce manuel ainsi que toutes ■ les consignes de sécurité avant d'utiliser Montage ■...
  • Page 42 TABLE DES MATIÈRES Réglages 27-29 Introduction Réglage des courses........27 Revue des symboles de sécurité...
  • Page 43: Préparation De Votre Porte De Garage

    AVERTISS Préparation de votre porte de garage AVERTISSEMENT AVERTISSEMENT Avant de commencer : Pour prévenir d’éventuelles BLESSURES GRAVES ou LA MORT : • Désactiver les serrures. • TOUJOURS appeler un technicien formé en systèmes de porte si • Retirer toute corde raccordée à la porte de garage. ATTENTION la porte de garage force ou est déséquilibrée.
  • Page 44: Planifi Cation

    Planifi cation Identifi er le type et la hauteur de votre porte de garage. Examiner la région POSE DE PORTES ARTICULÉES du garage pour noter si l’une des conditions ci-après s’applique à votre • Les panneaux de la porte sont-ils en acier, en aluminium, en fi bre installation.
  • Page 45 AVERTISS Planifi cation (Suite) AVERTISSEMENT AVERTISSEMENT POSE DE PORTE RIGIDE Sans système d’inversion de sécurité en bon état de marche, des • En règle générale, une porte rigide ne nécessite aucun renfort. Pour personnes (particulièrement les petits enfants) pourraient être une porte légère, prière de se reporter aux informations ayant trait aux ATTENTION GRIÈVEMENT BLESSÉES ou TUÉES par une porte de garage qui se...
  • Page 46: Inventaire De La Boîte D'emballage

    Inventaire de la boîte d’emballage Votre ouvre-porte de garage est emballé dans un boîte qui contiennent Les fi xations nécessaires au montage et à la pose apparaissent sur la le moteur et les pièces illustrées ci-après. Les accessoires dépendront page suivante. Conserver la boîte et le matériel d’emballage jusqu’au du modèle acheté.
  • Page 47: Inventaire Des Fi Xations

    Inventaire des fi xations Séparer toutes les fi xations et les regrouper comme illustré ci-après aux fi ns des opérations de montage et de pose. FIXATIONS POUR LE MONTAGE Contre-écrou de Rondelle-frein Écrou de Rondelle 5/8 po 1/4 de po-20 de 3/8 de po 3/8 de po Pièces d'extension de la chaîne...
  • Page 48: Montage

    AVERTISSEMENT MONTAGE - 1 OPÉRATION ATTENTION ATTENTION Montage du rail et pose du chariot Afi n de prévenir une BLESSURE occasionnée par un pincement, tenir Pour éviter les diffi cultés pendant la pose, ne faire fonctionner les mains et les doigts loin des joints lors de l’assemblage du rail. l'ouvre-porte de garage que lorsque cela est expressément indiqué.
  • Page 49 AVERTISSEMENT MONTAGE - 2 OPÉRATION ATTENTION ATTENTION Fixation du rail au moteur Afi n d’éviter d’endommager SÉRIEUSEMENT l’ouvre-porte de garage, 1. Insérer un boulon 1/4 po - 20 x 2-1/2, une rondelle et une entretoise utiliser UNIQUEMENT les boulons et les fi xations montés sur le à...
  • Page 50: Pose De La Chaîne Et Du Câble

    AVERTISS MONTAGE - 4 OPÉRATION AVERTISSEMENT AVERTISSEMENT Pose de la chaîne et du câble Pour éviter d’éventuelles BLESSURES GRAVES aux doigts par suite du 1. Tirer le câble autour de la poulie et vers le chariot. mouvement de l’ouvre-porte : ATTENTION 2.
  • Page 51: Tension De La Chaîne

    MONTAGE - 5 OPÉRATION Tension de la chaîne Figure 1 1. Dévisser l’écrou intérieur de la tige fi letée du chariot et éloigner la rondelle. Écrou Rondelle- Pour visser extérieur frein Arbre du 2. Pour tendre la chaîne, tourner l’écrou extérieur dans le sens illustré l'écrou extérieur chariot (Figure 1).
  • Page 52: Déterminer L'emplacement Du Support De Linteau

    POSE – 1 OPÉRATION AVERTISSEMENT Déterminer l’emplacement du support de linteau Plafond non fini MONTAGE DU SUPPORT DE AVERTISSEMENT AVERTISSEMENT AVERTISSEMENT LINTEAU AU PLAFOND EN OPTION Pour prévenir d’éventuelles BLESSURES GRAVES ou LA MORT : Linteau 2 X 4 • Le support de linteau DOIT être fi xé DE MANIÈRE RIGIDE à la solive Ligne du centre ATTENTION AVERTISSEMENT...
  • Page 53: Pose Du Support De Linteau

    POSE - 2 OPÉRATION Montage mural Pose du support de linteau Le support de linteau peut être fi xé soit sur le mur, au-dessus de la porte, soit sur le plafond. Suivre les instructions qui répondent le mieux aux besoins particuliers. Ne pas poser le support de linteau sur des plaques de placoplâtre.
  • Page 54: Fixation Du Rail Sur Le Support De Linteau

    POSE - 3 OPÉRATION Fixation du rail sur le support de linteau 1. Positionner l'ouvre-porte de garage sur le plancher, juste sous le support de linteau. Utiliser une des boîtes d'emballage pour le protéger. REMARQUE : Si le ressort de la porte gêne, il faudra demander de l’aide.
  • Page 55: Positionnement De L'ouvre-Porte

    AVERTISSEMENT POSE - 4 OPÉRATION ATTENTION ATTENTION Positionnement de l'ouvre-porte Pour prévenir les dommages à la porte de garage, faire reposer le rail Suivre les instructions qui se rapportent à la porte de garage particulière, de l’ouvre-porte de garage sur un 2 x 4 placé sur la section supérieure en se rapportant aux illustrations.
  • Page 56: Accrochage De L'ouvre-Porte

    POSE - 5 OPÉRATION AVERTISSEMENT AVERTISSEMENT Accrochage de l'ouvre-porte Pour éviter d’éventuelles BLESSURES GRAVES par suite de la chute Les illustrations représentent trois poses types. La pose peut toutefois d’un ouvre-porte de garage, fi xer l’ouvre-porte SOLIDEMENT aux AVERTISSEMENT AVERTI être différente.
  • Page 57: Pose De La Commande De Porte

    AVERTISSEMENT AVERTISSEMENT POSE - 6 OPÉRATION ATTENTION AVERTISSEMENT AVERTISSEMENT Pose de la commande de porte Pour prévenir d’éventuelles BLESSURES GRAVES ou LA MORT par Poser la commande murale dans un endroit où on pourra la voir de la suite d’électrocution : porte, à...
  • Page 58: Pose De L'ampoule

    AVERTISSEMENT POSE - 7 OPÉRATION ATTENTION ATTENTION Pose de l’ampoule Pour éviter toute SURCHAUFFE éventuelle du panneau d’éclairage, 1. Appuyer sur les pattes de dégagement des deux côtés du diffuseur. • NE PAS utiliser d’ampoules à col court ou de forme spéciale. Faire pivoter le diffuseur délicatement vers l’arrière et le bas jusqu’à...
  • Page 59: Exigences Électriques

    AVERTISSEMENT POSE - 9 OPÉRATION AVERTISSEMENT AVERTISSEMENT AVERTISSEMENT Exigences électriques Pour prévenir d’éventuelles BLESSURES GRAVES ou LA MORT par suite d’électrocution ou d’un incendie : Pour éviter les diffi cultés pendant la pose, ne pas faire fonctionner ATTENTION AVERTISSEMENT l'ouvre-porte pour le moment. •...
  • Page 60: Pose Du Système Protector

    POSE - 10 OPÉRATION AVERTISSEMENT AVERTISSEMENT ® Pose du Système Protector S’assurer que l’ouvre-porte de garage est hors tension AVANT de Les détecteurs inverseurs de sécurité doivent être bien branchés et poser le détecteur inverseur de sécurité. AVERTISSEMENT AVERTI bien alignés avant que l'ouvre-porte de garage puisse fermer la porte. Pour prévenir des BLESSURES GRAVES ou LA MORT par suite d’une porte de garage qui se ferme : INFORMATIONS IMPORTANTES AU SUJET DU DÉTECTEUR INVERSEUR...
  • Page 61 POSE DES SUPPORTS Figure 1 Figure 1 S’assurer que l’ouvre-porte est hors tension. MONTAGE SUR GUIDES DE PORTE (CÔTÉ DROIT) Poser et aligner les supports de manière à ce que les détecteurs se fassent face l’un l’autre de part et d’autre de la porte du garage, le Guide faisceau n’étant pas à...
  • Page 62 Figure 5 MONTAGE ET CÂBLAGE DES DÉTECTEURS INVERSEURS DE SÉCURITÉ 1. Faire glisser un boulon à tête bombée et collet carré de 1/4 po-20 x Écrou à oreilles 1/4 de po x 20 1/2 po dans la fente de chaque détecteur. Utiliser des écrous à oreilles pour fi...
  • Page 63 AVERTISSEMENT POSE - 11 OPÉRATION ATTENTION ATTENTION Fixation du support de porte Les portes de garage en fi bre de verre, en aluminium ou en acier léger Suivre les instructions qui correspondent au type de porte, comme ont BESOIN d’être renforcées AVANT la fi xation du support de porte. illustré...
  • Page 64 PORTES RIGIDES Prière de lire et de suivre les avertissements et les instructions de renforcements à la page précédente. Ils s’appliquent également aux portes rigides. • Centrer le support de porte sur le dessus de la porte, en l’alignant avec le support de linteau, comme il est illustré.
  • Page 65 Poulie POSE - 12 OPÉRATION Fixation de la biellette au chariot Suivre uniquement les instructions se rapportant au type de porte, comme illustré ci-dessous et à la page suivante. Chariot extérieur PORTE ARTICULÉE SEULEMENT Chariot intérieur Axe de chape de •...
  • Page 66 Figure 5 POUR TOUTES LES PORTES RIGIDES MAUVAIS 1. Assemblage des biellettes, Figure 5 : IMPORTANT : La rainure sur la biellette droite DOIT faire face a Biellette Biellette droite l’oppose de la biellette courbée. droite • Assembler les biellettes droite et courbée à leur plus grande Biellette (Rainure faisant longueur (2 ou 3 trous se chevauchant).
  • Page 67: Réglages

    AVERTISS RÉGLAGES - 1 OPÉRATION AVERTISSEMENT AVERTISSEMENT Réglage des courses d’ouverture et de fermeture Sans un système d’inversion de sécurité bien installé, des personnes Le réglage de ces courses fi xe les points où la porte s'arrêtera lors de son (plus particulièrement les petits enfants) pourraient être GRIÈVEMENT ouverture ou de sa fermeture.
  • Page 68: Réglage De La Force

    AVERTISS RÉGLAGES - 2 OPÉRATION AVERTISSEMENT AVERTISSEMENT Réglage de la force Sans un système d’inversion de sécurité bien installé, des personnes Les commandes de réglage de la force sont situées sur le panneau arrière (plus particulièrement les petits enfants) pourraient être GRIÈVEMENT du moteur.
  • Page 69: Essai Du Système Protector

    AVERTISS RÉGLAGES - 3 OPÉRATION AVERTISSEMENT AVERTISSEMENT Essai du système d’inversion de sécurité Sans un système d’inversion de sécurité bien installé, des personnes ESSAI (plus particulièrement les petits enfants) pourraient être GRIÈVEMENT ATTENTION 1. La porte étant entièrement ouverte, placer une planche de 1-1/2 po BLESSÉES ou TUÉES par une porte de garage qui se referme.
  • Page 70: Fonctionnement

    FONCTIONNEMENT IMPORTANTES CONSIGNES DE SÉCURITÉ AVERTISSEMENT AVERTISSEMENT Pour réduire le risque de BLESSURES GRAVES ou de MORT : 1. LIRE ET SUIVRE TOUS LES AVERTISSEMENTS ET INSTRUCTIONS. 9. Après avoir réglé une commande (force ou course), il peut être nécessaire de régler l’autre commande. 2.
  • Page 71: Utilisation De La Commande De Porte Murale

    Utilisation de la commande de porte mural Ouverture manuelle de la porte Appuyer sur le bouton-poussoir éclairé Bouton-poussoir éclairé AVERTISSEMENT AVERTISSEMENT pour ouvrir ou fermer la porte. Appuyer à nouveau pour inverser la porte durant le cycle de fermeture ou pour arrêter la porte Pour prévenir d’éventuelles BLESSURES GRAVES ou LA MORT par suite de la chute d’une porte de garage : pendant son ouverture.
  • Page 72: Entretien De Votre Ouvre-Porte De Garage

    Entretien de l’ouvre-porte de garage LA PILE DE LA TÉLÉCOMMANDE RÉGLAGES DE COURSE ET DE FORCE: AVERTISSEMENT AVERTISSEMENT Les conditions climatiques risquent de COMMANDES DE FORCE causer de petites modifi cations dans le Pour prévenir d’eventuelles BLESSURES GRAVES ou LA MORT : fonctionnement de la porte qui devra •...
  • Page 73: Défauts De Fonctionnement

    Défauts de fonctionnement 1. Ma porte ne se ferme pas et les ampoules de l’éclairage du moteur clignotent : Le détecteur inverseur de sécurité doit être raccordé et Fil de sonnerie aligné correctement avant que l’ouvre-porte de garage n’entame la procédure de fermeture.
  • Page 74: Fiche Diagnostique

    Fil de sonnerie Diagnostic situé Montage du sur le moteur détecteur inverseur de sécurité Voyant LED ou LED de Des fonctions d’autodiagnostic ont été programmées dans votre ouvre-porte de diagnostic garage. Le bouton « learn » ou le voyant LED de diagnostic émettra un certain Bouton nombre d’éclairs avant de faire une pause pour indiquer la découverte d’un Détecteur inverseur de sécurité...
  • Page 75: Programmation

    PROGRAMMATION REMARQUE : Si cet ouvre-porte de garage Security ✚ ® est utilisé avec une télécommande émettrice à code fi xe, le dispositif technique que contient le récepteur de l’ouvre-porte et qui procure une protection contre les vols de code, se trouvera contourné. Le détenteur des droits d’auteur de cet ouvre- porte de garage n’autorise pas l’acheteur ni le fournisseur de la télécommande émettrice à...
  • Page 76: Pour Ajouter, Reprogrammer Ou Modifi Er Un Nip D'entrée Sans Clé

    Pour ajouter, reprogrammer ou modifi er un NIP d’entrée sans clé REMARQUE : Votre nouvelle entrée sans clé doit être programmée de manière à faire fonctionner votre ouvre-porte de garage. UTILISATION DU BOUTON « LEARN » Pour défi nir un NIP temporaire Vous pouvez autoriser l’accès aux visiteurs ou aux techniciens de service à...
  • Page 77: Pièces De Réparation

    PIÈCES DE RÉPARATION Pièces d’assemblage du rail N° DE RÉF PIÈCE DÉSIGNATION 4A1008 Maillon de raccord 41C5141-1 Chariot complet 41A5665 Rail complet 144C56 Poulie de la chaîne 41A5807 Chaîne et câble 12D598-1 Support en U NON ILLUSTRÉS 183A163 Coussinets d’usure Pièces pour la pose N°...
  • Page 78: Pièces D'assemblage Du Moteur

    Pièces d’assemblage du moteur Contact INTERRUPTEUR DE (fermeture) FIN DE COURSE Fil brun Fil gris Pignon menant Contact de milieu Contact Fil jaune du course (ouverture) N° DE N° DE RÉF. PIÈCE DÉSIGNATION RÉF. PIÈCE DÉSIGNATION 41A5615 Écarteur de chaîne 41A5525-28 Couvercle 41C4220A...
  • Page 79: Accessoires

    GÉNÉRALITÉS : Les ouvre-portes de garage Craftsman sont garantis contre tout défaut de matériau ou de fabrication pendant une période de temps précise, telle qu’établie ci-dessous (la « période de garantie »). Cette garantie est offerte uniquement à l’acheteur initial du produit Craftsman et n’est pas transférable. Les achats effectués par l’entremise d’un encan en ligne ou sur tout site Web autre que www.sears.ca sont exclus.
  • Page 80 Faites-le réparer, à domicile ou à l’atelier! Téléphonez au: 1-800-LE-FOYER 1-800-533-6937) 24 heures par jour, 7 jours par semaine Pour la réparation des appareils électromémagers de grandes marques à votre domicile … peu importe le fabricant ou le détaillant! Pour connaître l’emplacement du Service des pièces et de l’entretien Sears le plus proche afin d’apporter à...

This manual is also suitable for:

139.18473dm139.18490dm139.18452dm139.18453dm

Table of Contents