Speaker Setup - Onkyo PR-SC5508 Instruction Manual

Speaker Setup

Main menu
Some of the settings in this section are set automatically
by Audyssey MultEQ
Speaker Setup (➔
Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup, or set them manually, which is useful if you change
one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup.
Note
• These settings are disabled when:
– a pair of headphones is connected, or
– the "Audio TV Out" setting is set to "On"
input selector other than HDMI is selected.
Speaker Settings
If you change these settings, you must run
Audyssey MultEQ XT32 Room Correction and
Speaker Setup again
If you bi-amp the front speakers, you must change the
"Speakers Type(Front)" setting
speaker wire connection, see "Bi-amping the Front Speak-
ers" (➔ 16).
Note
• When bi-amping is used, the AV controller is able to drive up to
7.2 speakers in the main room.
• Before you change these settings, turn down the volume.
■
Speakers Type(Front)
Normal:
Select this if you've connected your front speakers
normally.
Bi-Amp:
Select this if you've connected your front speakers
for bi-amped operation. The Bi AMP indicator will
light (➔ 9).
Note
• Surround back speakers cannot be used if you select "Bi-Amp".
• If the "Front High + Front Wide" setting is set to "Yes", the
"Speakers Type(Front)" setting is fixed at "Normal".
■
Front High + Front Wide
Yes:
Front High + Front Wide on.
No:
Front High + Front Wide off.
Listening mode that make use of "Front High + Front
Wide" setting is as follows;
Audyssey DSX (PLII/Neo:6 + Audyssey DSX included),
Orchestra, Unplugged, Studio-Mix, TV Logic, Game-
RPG, Game-Action, Game-Rock, Game-Sports, All Ch
Stereo, Full Mono.
En
48
Speaker Setup
® XT32 Room Correction and
29).
60) and an
(➔
(➔ 29).
(➔ 48). For details on
Note
• When you have selected "Yes",
– the "Surround Back" setting is set to "None".
– the "Front High" or "Front Wide" setting is set to
"80Hz(THX)" if set to "None".
• When you have selected "No", the "Front Wide" setting is set
to "None" if "Front High" and "Front Wide" settings are set to
anything other than "None".
• The "Front High + Front Wide" setting cannot be used if
"Speakers Type(Front)" is set to "Bi-Amp".
Speaker Configuration
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
29).
Setup function (➔
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify "Full Band" for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies.
If you set up your speakers using Audyssey MultEQ XT32
Room Correction and Speaker Setup, please make sure
manually that any THX speakers are set to "80Hz(THX)"
crossover.
■
Subwoofer
1ch:
Audio signal is outputted from SW1 jack only.
2ch:
Audio signal is outputted from SW1 and SW2
jacks.
No:
Select if no subwoofer is connected.
■
Front
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed at "Full Band".
■
Center *1 , Surround *1 , Surround Back
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None:
Select if no speaker is connected.
■
Front Wide *1*2*6 , Front High
Full Band
40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
None:
Select if no speaker is connected.
*2*3*4*5
*1*2*6