General Safety Rules; Additional Safety Instructions For Planers - Black & Decker 7698 Instruction Manual

PORTUGUÊS
BISEL DAS BORDAS
A ranhura em forma de "V" na ponta da peça da base possibilita chanfrar as bordas em ângulos de 45º.
• Segure a ferramenta em um ângulo com a ranhura sobre a borda da peça de trabalho e realize a passada de corte.
• Recomenda-se a realização de um teste em um pedaço de madeira antes de fazer o trabalho de acabamento.
ESVAZIAMENTO DO SACO COLETOR DE REBARBAS
O saco coletor de rebarbas deve ser esvaziado regularmente durante o uso.
• Abra o fecho do saco e esvazie-o antes de continuar o trabalho.
DICAS PARA UMA OPERAÇÃO OTIMIZADA
• Mova a ferramenta no sentido dos veios da madeira.
• Se os veios forem transversais ou ondulados, ou se o material da peça de trabalho for de um tipo duro,
ajuste a profundidade do corte para retirar apenas uma rebarba muito fina a cada passada. Além disso,
passe várias vezes para obter o resultado desejado.
• Para manter a ferramenta em linha reta, pressione para baixo a parte frontal da ferramenta quando iniciar o trabalho,
e pressione para baixo a parte posterior da ferramenta no final da passada de corte.
TROCA DA CORREIA DE TRANSMISSÃO (FIG. G)
• Solte os parafusos (20) e remova a cobertura (21).
• Remova a correia de transmissão antiga.
• Instale correia nova (22) sobre as roldanas. Coloque primeiro a correia sobre a roldana maior (23),
depois sobre a roldana menor (24), enquanto gira manual e regularmente a correia.
• Coloque a cobertura novamente no lugar e aperte os parafusos.
MANUTENÇÃO
Sua ferramenta foi desenhada para funcionar durante um período longo de tempo, necessitando de uma manutenção
mínima. Seu funcionamento contínuo e satisfatório dependerá do cuidado devido da ferramenta, que são eles:
• Limpe regularmente as entradas de ventilação de sua ferramenta com uma escova suave ou um panoseco.
• Limpe regularmente a caixa protetora do motor com um pano úmido.
• Não utilize materiais abrasivos ou que tenham em sua fórmula solventes para limpar a ferramenta. Nunca deixe entrar
ou escorrer líquidos para dentro da ferramenta ou mergulhe quaisquer peças da ferramenta em produtos líquidos.
PROTEÇÃO AO MEIO AMBIENTE
Coleta Seletiva.
Este produto não deve ser descartado junto com o lixo doméstico normal.
Caso ache necessário que seu produto Black & Decker seja substituído, ou caso não seja mais útil para você, não
jogue-o fora junto com o lixo doméstico normal. Disponibilize este produto para coleta seletiva.
A coleta seletiva de produtos e embalagens usadas permite que os materiais sejam reciclados e
utilizados novamente. A reutilização de materiais reciclados ajuda a prevenir poluição ambiental e reduz
a demanda de matéria prima.
Regulamentos locais podem prever a coleta seletiva de produtos elétricos domésticos, em lixeiras municipais ou
pelo vendedor ao comprar um produto novo.
ASSISTÊNCIA TÉCNICA
A Black & Decker possui uma das maiores Redes de Serviços do País, com técnicos treinados para manter e reparar
toda a linha de produtos Black & Decker. Ligue: 0800-703 4644 ou consulte nosso site: http://www.blackedecker.com.br,
para saber qual é a mais próxima de sua localidade.
ESPECIFICAÇÕES
Voltagem
AR 220V ~ 50Hz
B2C 220V ~ 50-60Hz
B3 120V ~ 60Hz
B2 220V ~ 60Hz
BR 127V ~ 60Hz
Potência 650W
0
Velocidade Sem Carga n 16500/min
16500 rpm
KEY INFORMATION YOU SHOULD KNOW:
• For aggressive material removal, use several controlled passes at a shallow depth of cut.
• For optimum results use smooth uninterrupted passes.

GENERAL SAFETY RULES

WARNING:
Read and understand all instructions. Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS
General power tool safety warnings
Warning! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk
of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable
for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
NOTE: The term "Residual Curent Device (RCD)" can be replaced by "Ground Fault Circuit Interrupter (GFCI)"
or by "Earth Leakage Circuit Breaker (ELCB)".
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool.
Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye, ear and respiratory protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch
or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before making
any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the power tools operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into
account the working conditions and the work to be performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
6. Electrical Safety
Your charger is double insulated; therefore no earth wire is required. Always check that the mains voltage
corresponds to the voltage on the rating plate. Never attempt to replace the charger unit with a regular mains
plug.
Warning! If the power cord is damaged, it must be replaced by the manufacturer, authorized Black & Decker
Service Center or an equally qualified person in order to avoid damage or injury. If the power cord is replaced
by an equally qualified person, but not authorized by Black & Decker, the warranty will not be valid.
7. Labels on Tool
The label on your tool may include the following symbols:
Read Instruction Manual
Use Eye Protection
Use Ear Protection
V...............................Volts
A.............................. Amperes
Hz............................ Hertz
W..............................Watts
min...........................minutes
...........................Alternating current

ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERS

• Read instruction manual thoroughly before using this tool.
• Be sure the switch is in OFF position before connecting tool to power supply.
• Switch OFF immediately if tool is jammed in work.
• Disconnected from power source when cleaning or making adjustments to the tool.
• Be sure tool is properly held or set for right use before turning switch to ON.
• Maintain tool with care. Follow instructions for lubricating and changing accessories.
• Store tool in a clean dry place after disconnecting from power source.
• Keep air vents unobstructed for proper motor cooling.
• DO NOT lay tool down on shoe when the blades are exposed. This can chip the blades.
ENGLISH
...........................Direct current
n ............................. No load speed
0
...........................Class II Construction
...........................Earthing terminal
...........................Safety alert symbol
.../min...................... Revolutions or reciprocations
per minute