Related Manuals for Phil & Teds Evolution BS01-B
Summary of Contents for Phil & Teds Evolution BS01-B
- Page 1 evolution ™ Group 0+I (0-25kg) SUITABLE FOR BS01-B/S The product has been approved according to the strictest BS01-BE/SE European safety standards (ECE R 44/04) and is suitable BS01-BC/SC for Group 0+I+11(0-25KG). BS01-BCE/SCE...
- Page 2 Introduction The evolution complies with requirements applicable in market ™ of sale Dear parents Thank you very much for purchasing our product. The function and design of this seat delivers the highest For rights & remedies, refer www.philandteds.com/warranty levels of safety and comfort when your child is in this child restraint.
-
Page 3: Table Of Contents
Content children weight between 0-13kg Introduction 4.2 Installation of Group I and it is for the Important children weight between 9-18kg Know your car seat 4.3 Installation of Group II and it is for the 1. Suitability children weight between 15-25kg 1.1 Certification 5. -
Page 4: Important
Important /03 R16 or an equivalent standard. Important The product may be used on either the front or WARNING: Read this instruction manual carefully. the back seat. WARNING: The correct fitting of the seat belt, However, we recommend that it is fitted on the along the red marking between the shell and back seat. - Page 5 Important /04 It is recommended that the car seat should not Use the seat even in a short journey, as this is be used more than 5 years from the date of when most accidents occur. production. The properties of the products may Before the purchase, please check that the seat is deteriorate due to, for example, ageing of the properly in your car.
-
Page 6: Know Your Car Seat
Know your car seat /05 Cover 2. Group II guide hook 3. Shell 4. Belt guard door 5. Hole 6. Base 7. Belt Yoke 8. Hooks for lap belt 9. Lock-off device 10. Upper shaft and lock 11. Shoulder strap connector 12. - Page 7 Know your car seat /06 16. Head pillow 17. Belt pads 18. Shoulder belt 19. Cushion 20. Adjusting cover 21. Adjuster belt 22. Positioning handle 23. Adjusting device 24. Buckle pad 25. Buckle 26. Belt slots 27. Belt clip 28. Belt clip slot 29.
-
Page 8: Suitability
Suitability /07 1. Suitability 1.1 Certification as a child safety seat installed The child safety seat has been designed, tested in a vehicle and certified according to the requirements of the European Standard for Child Safety Equipment (ECE R 44/04). Tested and certified according to ECE* R 44/04 Child Safety Seat... -
Page 9: Use In The Vehicle
Use in the vehicle /08 2. Use in the vehicle DO NOT use on a passenger DO NOT use with a 2-point belt - seat with a front airbag! use with a vehicle’s 3-point seatbelt. Danger! An airbag hitting a child safety seat can Please observe the regulations applicable to your cause serious injuries to your child, possibly particular country. -
Page 10: With The Vehicle's 3-Point Seatbelt
Use in the vehicle /09 2.1 With the vehicle's 3-point seatbelt 1. The use of a 2-point belt substantially You can use your child safety seat as follows: increases the risk of injury to your child in the event of an accident. 2. -
Page 11: Securing Your Baby
Securing your baby /10 Securing your baby 3.1 Securing your baby using the Always secure your baby in the car seat using the baby insert harness. Never leave your baby unattended in the car seat For the protection of your baby when placing it on elevated surfaces (e.g. -
Page 12: Five Positions Of The Car Seat
Securing your baby /11 3.2 Five Positions of the Car Seat • The shoulder harnesses can be set to four heights and must be passed through the holes closest to the shoulders of your child. If the The car seat can be used in five positions: shoulders of your child are between two pairs • Lift the handle under the front of the seat up and of holes, use the higher ones. - Page 13 Securing your baby /12 • Make sure that the buckle remains fixed to prevent the belts twisting. • Close the belt guard door (3-H), insert the lower shaft in to the seat (3-I) and latch in place. • If you wish to alter the belts from or to the lowest position, place the baby car seat in the sleeping position.
-
Page 14: Securing Your Baby Using The Harness
Securing your baby /13 3.4 Securing your baby using the harness The car seat can be used in five positions: • Loosen the shoulder belts by pressing the release button and pulling the shoulder belts as far as you can. Note! Do not pull the belt pads (3-J). -
Page 15: Tightening The Harness
Securing your baby /14 • The shoulder straps of the car seat are 3.5 Tightening the harness comfortable but firm fit around your child. • The shoulder straps are adjusted correctly. • The shoulder straps are not twisted. • Pull the strap end. •... -
Page 16: Installation In The Vehicle
Installation in the vehicle /15 Installation in the vehicle Please do not leave your child unattended in the child safety seat in the vehicle. For the protection of all vehicle occupants To protect your vehicle Some vehicle seat covers of sensitive materials •... -
Page 17: Children Weight Between 0-13Kg
Installation in the vehicle /16 4.1 Installation of Group 0+ for children weight 0-13kg. Children with a body weight of under 9 kg must be secured with this car seat rearward facing. We recommend using the seat rearward facing until your child has reached a body weight of 13kg. Place the seat rearward facing in your car: • Clip out the leg support (4-A). - Page 18 Installation in the vehicle /17 4.2 Installation of Group I for children 9-18kg. • Adjust the baby car seat into the sleeping position (3-B). • Take the lower shaft out of the seat, then pull the seat back (4-G). • Install the safety belt through the seat back from the middle of top and fix into the buckle on the car seat (4-H).
-
Page 19: Installation In The Vehicle
Installation in the vehicle /18 4.3 Installation of Group II for children 15-25kg. • Before the installation, please remove the belt system of baby car seat (see section 5.1) (including belt pads, shoulder belt, buckle & crotch strap jacket (4-L). •... -
Page 20: Care Instructions
Care Instructions /19 5. Care Instructions 5.1 Removing the 5-point harness system and cover • Loosen the belts and the belt pads, see fig. 3-C to 3-E under section 3.3 • Loosen the bottom part of the cover and pull the belt clip through the belt clip slot (5-A). -
Page 21: Refitting The 5-Point Harness System And Cover
Care Instructions /20 5.2 Refitting the 5-point harness system and cover • After washing, place the cover on the shell (5-D). • Loosen the bottom part of the cover and pull the belt clip through the belt clip slot (5-E). •... -
Page 22: Cleaning
Care Instructions /21 5.3 Cleaning The harness can be removed and washed in lukewarm soapy water. Caution! Never remove the buckle tongues from Please be sure to use only original replacement the straps. seat covers, as the seat cover is important to the proper functioning of the system. -
Page 23: Warranty
Care Instructions /22 Make sure that you have the following details to the manufacturer. Repairs do not constitute an hand: extension to the warranty term. The manufacturer is not liable for any damages other than those on • Serial number underneath. products supplied. -
Page 24: Additional Instruction
Additional Instruction /23 Additional Instruction BS02-BE/SE BS02-BC/SC BS02-BCE/SCE Side Armor gives you more “CuddleMe” is a very Owning all of the premium protection against side cozy and human-oriented features of “Cuddle Me” and impact. When you wash the designed foam. Please “Side Armor”, brings you cover, please firstly take off don't wash this foam when... - Page 26 Notice AU/NZ 1. This is a Universal child restraint. It is approved to phil&teds Regulation No.44,04 series of amendments, for general 102-112 Daniell Street use in vehicles and it will fit most, but not all, car seats. Newtown, Wellington 6021 2.