Connecting A Turntable; Connecting A Tv Or Other Component With An Audio Output; Connecting A Preamp; Connecting Another Component's Power Cord - Onkyo A-933 Instruction Manual

*En_A933_02.fm Page 15 Tuesday, January 25, 2005 1:46 PM
Connecting the A-933 —Continued

Connecting a Turntable

The A-933's PHONO input jacks are for use with mov-
ing-magnet (MM) type cartridges.
Use an analog audio cable to connect the A-933's
PHONO L/R jacks to the audio output jacks on the turn-
table, as shown.
L
GND GND
L L L
B
R R R
R
PHONO (MM) PHONO (MM) TUNER CD
L L L
SUBWOOFER
PREOUT
R R R
REMOTE
OUT IN OUT IN CONTROL
MAIN IN MD
TAPE/CDR
AUDIO OUT
L
R
PHONO (MM)
Ground wire
Notes:
• If the turntable has a ground wire, connect it to
A-933's GND terminal. With some turntables, con-
necting the ground wire may cause hum, in which
case it should be disconnected.
• If the turntable has a moving-coil (MC) type car-
tridge, you'll need a commercially available MC
phono preamp. In this case, connect the turntable to
the phono preamp's input, and connect the phono
preamp's output to the A-933's PHONO L/R jacks.
Connecting a TV or Other Component with
an Audio Output
Use an analog audio cable to connect the A-933's LINE
L/R jacks to the analog audio output jacks on the TV or
other component, as shown.
L L
GND
L L
R R
R R
PHONO (MM) TUNER CD
L L L
SUBWOOFER
PREOUT
R R R
REMOTE
OUT IN OUT IN CONTROL
MAIN IN MD
TAPE/CDR
Note:
If your TV has no audio output, you can connect the
A-933 to an audio output on your VCR and use its tuner.
SPEAKERS
A
AC OUTLET
AC 230-240 V
R L R L 50 Hz
UNSWITCHED
TOTAL 100 W MAX.
CAUTION: SPEAKER IMPEDANCE
INTEGRATED AMPLIFIER A or B : 4 OHMS MIN. /SPEAKER
A- 933 A + B : 8 OHMS MIN. /SPEAKER
MODEL NO.
L
R
L
SPEAKERS
R
B A
AC OUTLET
LINE
AC 230-240 V
R L R L 50 Hz
UNSWITCHED
TOTAL 100 W MAX.
CAUTION: SPEAKER IMPEDANCE
INTEGRATED AMPLIFIER A or B : 4 OHMS MIN. /SPEAKER
MODEL NO. A- 933 A + B : 8 OHMS MIN. /SPEAKER
AUDIO OUT
L
R

Connecting a Preamp

The A-933 can be used as a power amplifier with a sep-
arate preamp.
In this case, use an analog audio cable to connect the
A-933's MAIN IN jacks to the preamp's output jacks.
Connect the speakers to the A-933, and connect the
playback components to the preamp.
GND
L L
R R
PHONO (MM) TUNER
L
L L L
SUBWOOFER
PREOUT
R
R R R
OUT
MAIN IN MAIN IN MD
MAIN IN
PRE OUT
L
R
Notes:
• Do not connect a component that does not have an
output volume control, because the sound will be out-
put at maximum volume and may damage the A-933
and your speakers.
• To turn on the MAIN IN function, press the [MAIN
IN] button for 3 seconds until the indicator lights up
blue (page 19).
• When the A-933 is used as a power amplifier, the
remote controller and the following functions are dis-
abled: Volume control, Muting,
Tone/Direct function, subwoofer output, and Record-
ing. Some of these functions can be performed on the
connected preamp.
Connecting Another Component's Power
Cord
The A-933 has an AC OUTLET on its rear panel. This
can be used to connect the power cord of another audio
component that you intend to use with the A-933.
L
SPEAKERS
B A
R
CD
AC OUTLET
L AC 230-240 V
R L R L 50 Hz
UNSWITCHED
TOTAL 100 W MAX.
R
REMOTE
OUT IN CONTROL
CAUTION: SPEAKER IMPEDANCE
TAPE/CDR
INTEGRATED AMPLIFIER A or B : 4 OHMS MIN. /SPEAKER
A- 933 A + B : 8 OHMS MIN. /SPEAKER
MODEL NO.
Caution:
• Make sure that the maximum power requirement of
the component connected to the AC OUTLET does
not exceed the capacity printed on the A-933's rear
panel (100W).
L
SPEAKERS
B A
R
CD
L
R L R L
R
REMOTE
IN OUT IN
CONTROL
TAPE/CDR
INTEGRATED AMPLIFIER
A- 933
MODEL NO.
system functions,
AC OUTLET
AC 230-240 V
50 Hz
UNSWITCHED
TOTAL 100 W MAX.
15